diff --git a/arch/arm/mach-keystone/config.mk b/arch/arm/mach-keystone/config.mk
index 3fcda92398..ff2fa68327 100644
--- a/arch/arm/mach-keystone/config.mk
+++ b/arch/arm/mach-keystone/config.mk
@@ -15,8 +15,10 @@ OBJCOPYFLAGS_u-boot-spi.gph = -I binary -O binary --pad-to=$(CONFIG_SPL_PAD_TO)
 u-boot-spi.gph: spl/u-boot-spl.gph u-boot.img FORCE
 	$(call if_changed,pad_cat)
 
-MKIMAGEFLAGS_u-boot-nand.gph = -A $(ARCH) -T gpimage -C none \
+ifndef CONFIG_SPL_BUILD
+MKIMAGEFLAGS_MLO = -A $(ARCH) -T gpimage -C none \
 	-a $(CONFIG_SYS_TEXT_BASE) -e $(CONFIG_SYS_TEXT_BASE) -n U-Boot
-u-boot-nand.gph: u-boot.bin FORCE
+MLO: u-boot.bin FORCE
 	$(call if_changed,mkimage)
 	@dd if=/dev/zero bs=8 count=1 2>/dev/null >> $@
+endif
diff --git a/board/ti/ks2_evm/README b/board/ti/ks2_evm/README
index 6586faba32..b8247256e9 100644
--- a/board/ti/ks2_evm/README
+++ b/board/ti/ks2_evm/README
@@ -61,7 +61,7 @@ Supported image formats:
  - u-boot.bin: for loading and running u-boot.bin through Texas instruments
                code composure studio (CCS)
  - u-boot-spi.gph: gpimage for programming SPI NOR flash for SPI NOR boot
- - u-boot-nand.gph: gpimage for programming AEMIF NAND flash for NAND boot
+ - MLO: gpimage for programming AEMIF NAND flash for NAND boot
 
 Build instructions:
 ===================
@@ -76,9 +76,9 @@ To build u-boot-spi.gph
   >make k2hk_evm_defconfig
   >make u-boot-spi.gph
 
-To build u-boot-nand.gph
+To build MLO
   >make k2hk_evm_defconfig
-  >make u-boot-nand.gph
+  >make MLO
 
 Load and Run U-Boot on keystone EVMs using CCS
 =========================================
@@ -157,12 +157,12 @@ instructions:
 1. Start CCS and run U-boot as described above.
 2. Suspend Target. Select Run -> Suspend from top level menu
    CortexA15_1 (Free Running)"
-3. Load u-boot-nand.gph binary from build folder on to DDR address 0x87000000
+3. Load MLO binary from build folder on to DDR address 0x87000000
    through CCS as described in step 2 of "Load and Run U-Boot on K2HK EVM
    using CCS", but using address 0x87000000.
 4. Free Run the target as described earlier (step 4) to get u-boot prompt
 5. At the U-Boot console type following to setup u-boot environment variables.
-   setenv filesize <size in hex of u-boot-nand.gph rounded to hex 0x10000>
+   setenv filesize <size in hex of MLO rounded to hex 0x10000>
    run burn_uboot_nand
    Once u-boot prompt is available, Power OFF the EVM. Set the SW1 dip switch
    to "ARM NAND Boot mode" as per instruction at