u-boot/board/xilinx/common/board.c

659 lines
15 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2014 - 2020 Xilinx, Inc.
* Michal Simek <michal.simek@xilinx.com>
*/
#include <common.h>
#include <efi.h>
#include <efi_loader.h>
#include <env.h>
#include <image.h>
#include <lmb.h>
#include <log.h>
#include <asm/global_data.h>
#include <asm/sections.h>
#include <dm/uclass.h>
#include <i2c.h>
#include <linux/sizes.h>
#include <malloc.h>
#include "board.h"
#include <dm.h>
#include <i2c_eeprom.h>
#include <net.h>
#include <generated/dt.h>
#include <soc.h>
xilinx: common: Enabling generic function for DT reselection U-Boot support board detection at run time and based on it change DT. This feature is implemented for SOM Kria platforms which contain two eeproms which contain information about SOM module and CC (Carrier card). Full U-Boot starts with minimal DT file defined by CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image. It is using default setup of board_name variable initializaed to DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option. When DTB_RESELECT is enabled board_detection() is called. Keep it your mind that this code is called before relocation. board_detection() is calling xilinx_read_eeprom() which fills board_info (xilinx_board_description) structure which are parsed in board_name_decode(). Based on DT configuration and amount of nvmemX aliases name of the board is composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev" <board_revision> "-" <cc_name> "-rev" <cc_revision>. If CC is not present or more are available it keeps going. When board name is composed and returned from board_name_decode() it is assigned to board_name variable which is used by board_fit_config_name_match() which is called via fdtdec_setup() when it goes over config options in multi dtb FIT image. From practical point of view multi DTB image is key point here which has to contain configs for detected combinations. Unfortunately as of now they have to be full DTBs and DTBOs are not supported. That's why configuration like: config_X { description = "zynqmp-board-cc"; fdt = "board", "cc"; }; needs to be squashed together with: fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \ arch/arm/dts/zynqmp-cc.dtbo and only one dtb is in fit: config_X { description = "zynqmp-board-cc"; fdt = "board-cc"; }; For creating multi DTBs fit image use mkimage -E, e.g.: mkimage -E -f all.its all.dtb When DTB_RESELECT is enabled xilinx_read_eeprom() is called before relocation and it uses calloc for getting a buffer. Because this is dynamic memory it is not relocated that's why xilinx_read_eeprom() is called again as the part of board_init(). This second read with calloc buffer placed in proper position board_late_init_xilinx() can setup u-boot variables as before. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-11 12:23:54 +00:00
#include <linux/ctype.h>
#include <linux/kernel.h>
#include <uuid.h>
#include "fru.h"
#if CONFIG_IS_ENABLED(EFI_HAVE_CAPSULE_SUPPORT)
struct efi_fw_image fw_images[] = {
#if defined(XILINX_BOOT_IMAGE_GUID)
{
.image_type_id = XILINX_BOOT_IMAGE_GUID,
.fw_name = u"XILINX-BOOT",
.image_index = 1,
},
#endif
#if defined(XILINX_UBOOT_IMAGE_GUID)
{
.image_type_id = XILINX_UBOOT_IMAGE_GUID,
.fw_name = u"XILINX-UBOOT",
.image_index = 2,
},
#endif
};
struct efi_capsule_update_info update_info = {
.images = fw_images,
};
u8 num_image_type_guids = ARRAY_SIZE(fw_images);
#endif /* EFI_HAVE_CAPSULE_SUPPORT */
#if defined(CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET)
int zynq_board_read_rom_ethaddr(unsigned char *ethaddr)
{
int ret = -EINVAL;
struct udevice *dev;
ofnode eeprom;
eeprom = ofnode_get_chosen_node("xlnx,eeprom");
if (!ofnode_valid(eeprom))
return -ENODEV;
debug("%s: Path to EEPROM %s\n", __func__,
ofnode_read_chosen_string("xlnx,eeprom"));
ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom, &dev);
if (ret)
return ret;
ret = dm_i2c_read(dev, CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET, ethaddr, 6);
if (ret)
debug("%s: I2C EEPROM MAC address read failed\n", __func__);
else
debug("%s: I2C EEPROM MAC %pM\n", __func__, ethaddr);
return ret;
}
#endif
#define EEPROM_HEADER_MAGIC 0xdaaddeed
#define EEPROM_HDR_MANUFACTURER_LEN 16
#define EEPROM_HDR_NAME_LEN 16
#define EEPROM_HDR_REV_LEN 8
#define EEPROM_HDR_SERIAL_LEN 20
#define EEPROM_HDR_NO_OF_MAC_ADDR 4
#define EEPROM_HDR_ETH_ALEN ETH_ALEN
#define EEPROM_HDR_UUID_LEN 16
struct xilinx_board_description {
u32 header;
char manufacturer[EEPROM_HDR_MANUFACTURER_LEN + 1];
char name[EEPROM_HDR_NAME_LEN + 1];
char revision[EEPROM_HDR_REV_LEN + 1];
char serial[EEPROM_HDR_SERIAL_LEN + 1];
u8 mac_addr[EEPROM_HDR_NO_OF_MAC_ADDR][EEPROM_HDR_ETH_ALEN + 1];
char uuid[EEPROM_HDR_UUID_LEN + 1];
};
static int highest_id = -1;
static struct xilinx_board_description *board_info;
#define XILINX_I2C_DETECTION_BITS sizeof(struct fru_common_hdr)
/* Variable which stores pointer to array which stores eeprom content */
struct xilinx_legacy_format {
char board_sn[18]; /* 0x0 */
char unused0[14]; /* 0x12 */
char eth_mac[6]; /* 0x20 */
char unused1[170]; /* 0x26 */
char board_name[11]; /* 0xd0 */
char unused2[5]; /* 0xdc */
char board_revision[3]; /* 0xe0 */
char unused3[29]; /* 0xe3 */
};
static void xilinx_eeprom_legacy_cleanup(char *eeprom, int size)
{
int i;
char byte;
for (i = 0; i < size; i++) {
byte = eeprom[i];
/* Remove all ffs and spaces */
if (byte == 0xff || byte == ' ')
eeprom[i] = 0;
/* Convert strings to lower case */
if (byte >= 'A' && byte <= 'Z')
eeprom[i] = byte + 'a' - 'A';
}
}
static int xilinx_read_eeprom_legacy(struct udevice *dev, char *name,
struct xilinx_board_description *desc)
{
int ret, size;
struct xilinx_legacy_format *eeprom_content;
bool eth_valid = false;
size = sizeof(*eeprom_content);
eeprom_content = calloc(1, size);
if (!eeprom_content)
return -ENOMEM;
debug("%s: I2C EEPROM read pass data at %p\n", __func__,
eeprom_content);
ret = dm_i2c_read(dev, 0, (uchar *)eeprom_content, size);
if (ret) {
debug("%s: I2C EEPROM read failed\n", __func__);
free(eeprom_content);
return ret;
}
xilinx_eeprom_legacy_cleanup((char *)eeprom_content, size);
printf("Xilinx I2C Legacy format at %s:\n", name);
printf(" Board name:\t%s\n", eeprom_content->board_name);
printf(" Board rev:\t%s\n", eeprom_content->board_revision);
printf(" Board SN:\t%s\n", eeprom_content->board_sn);
eth_valid = is_valid_ethaddr((const u8 *)eeprom_content->eth_mac);
if (eth_valid)
printf(" Ethernet mac:\t%pM\n", eeprom_content->eth_mac);
/* Terminating \0 chars ensure end of string */
strcpy(desc->name, eeprom_content->board_name);
strcpy(desc->revision, eeprom_content->board_revision);
strcpy(desc->serial, eeprom_content->board_sn);
if (eth_valid)
memcpy(desc->mac_addr[0], eeprom_content->eth_mac, ETH_ALEN);
desc->header = EEPROM_HEADER_MAGIC;
free(eeprom_content);
return ret;
}
static bool xilinx_detect_legacy(u8 *buffer)
{
int i;
char c;
for (i = 0; i < XILINX_I2C_DETECTION_BITS; i++) {
c = buffer[i];
if (c < '0' || c > '9')
return false;
}
return true;
}
static int xilinx_read_eeprom_fru(struct udevice *dev, char *name,
struct xilinx_board_description *desc)
{
int i, ret, eeprom_size;
u8 *fru_content;
u8 id = 0;
/* FIXME this is shortcut - if eeprom type is wrong it will fail */
eeprom_size = i2c_eeprom_size(dev);
fru_content = calloc(1, eeprom_size);
if (!fru_content)
return -ENOMEM;
debug("%s: I2C EEPROM read pass data at %p\n", __func__,
fru_content);
ret = dm_i2c_read(dev, 0, (uchar *)fru_content,
eeprom_size);
if (ret) {
debug("%s: I2C EEPROM read failed\n", __func__);
goto end;
}
fru_capture((unsigned long)fru_content);
xilinx: common: Enabling generic function for DT reselection U-Boot support board detection at run time and based on it change DT. This feature is implemented for SOM Kria platforms which contain two eeproms which contain information about SOM module and CC (Carrier card). Full U-Boot starts with minimal DT file defined by CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image. It is using default setup of board_name variable initializaed to DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option. When DTB_RESELECT is enabled board_detection() is called. Keep it your mind that this code is called before relocation. board_detection() is calling xilinx_read_eeprom() which fills board_info (xilinx_board_description) structure which are parsed in board_name_decode(). Based on DT configuration and amount of nvmemX aliases name of the board is composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev" <board_revision> "-" <cc_name> "-rev" <cc_revision>. If CC is not present or more are available it keeps going. When board name is composed and returned from board_name_decode() it is assigned to board_name variable which is used by board_fit_config_name_match() which is called via fdtdec_setup() when it goes over config options in multi dtb FIT image. From practical point of view multi DTB image is key point here which has to contain configs for detected combinations. Unfortunately as of now they have to be full DTBs and DTBOs are not supported. That's why configuration like: config_X { description = "zynqmp-board-cc"; fdt = "board", "cc"; }; needs to be squashed together with: fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \ arch/arm/dts/zynqmp-cc.dtbo and only one dtb is in fit: config_X { description = "zynqmp-board-cc"; fdt = "board-cc"; }; For creating multi DTBs fit image use mkimage -E, e.g.: mkimage -E -f all.its all.dtb When DTB_RESELECT is enabled xilinx_read_eeprom() is called before relocation and it uses calloc for getting a buffer. Because this is dynamic memory it is not relocated that's why xilinx_read_eeprom() is called again as the part of board_init(). This second read with calloc buffer placed in proper position board_late_init_xilinx() can setup u-boot variables as before. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-11 12:23:54 +00:00
if (gd->flags & GD_FLG_RELOC || (_DEBUG && CONFIG_IS_ENABLED(DTB_RESELECT))) {
printf("Xilinx I2C FRU format at %s:\n", name);
ret = fru_display(0);
if (ret) {
printf("FRU format decoding failed.\n");
goto end;
}
}
if (desc->header == EEPROM_HEADER_MAGIC) {
debug("Information already filled\n");
ret = -EINVAL;
goto end;
}
/* It is clear that FRU was captured and structures were filled */
strlcpy(desc->manufacturer, (char *)fru_data.brd.manufacturer_name,
sizeof(desc->manufacturer));
strlcpy(desc->uuid, (char *)fru_data.brd.uuid,
sizeof(desc->uuid));
strlcpy(desc->name, (char *)fru_data.brd.product_name,
sizeof(desc->name));
for (i = 0; i < sizeof(desc->name); i++) {
if (desc->name[i] == ' ')
desc->name[i] = '\0';
}
strlcpy(desc->revision, (char *)fru_data.brd.rev,
sizeof(desc->revision));
for (i = 0; i < sizeof(desc->revision); i++) {
if (desc->revision[i] == ' ')
desc->revision[i] = '\0';
}
strlcpy(desc->serial, (char *)fru_data.brd.serial_number,
sizeof(desc->serial));
while (id < EEPROM_HDR_NO_OF_MAC_ADDR) {
if (is_valid_ethaddr((const u8 *)fru_data.mac.macid[id]))
memcpy(&desc->mac_addr[id],
(char *)fru_data.mac.macid[id], ETH_ALEN);
id++;
}
desc->header = EEPROM_HEADER_MAGIC;
end:
free(fru_content);
return ret;
}
static bool xilinx_detect_fru(u8 *buffer)
{
u8 checksum = 0;
int i;
checksum = fru_checksum((u8 *)buffer, sizeof(struct fru_common_hdr));
if (checksum) {
debug("%s Common header CRC FAIL\n", __func__);
return false;
}
bool all_zeros = true;
/* Checksum over all zeros is also zero that's why detect this case */
for (i = 0; i < sizeof(struct fru_common_hdr); i++) {
if (buffer[i] != 0)
all_zeros = false;
}
if (all_zeros)
return false;
debug("%s Common header CRC PASS\n", __func__);
return true;
}
static int xilinx_read_eeprom_single(char *name,
struct xilinx_board_description *desc)
{
int ret;
struct udevice *dev;
ofnode eeprom;
u8 buffer[XILINX_I2C_DETECTION_BITS];
eeprom = ofnode_get_aliases_node(name);
if (!ofnode_valid(eeprom))
return -ENODEV;
ret = uclass_get_device_by_ofnode(UCLASS_I2C_EEPROM, eeprom, &dev);
if (ret)
return ret;
ret = dm_i2c_read(dev, 0, buffer, sizeof(buffer));
if (ret) {
debug("%s: I2C EEPROM read failed\n", __func__);
return ret;
}
debug("%s: i2c memory detected: %s\n", __func__, name);
if (CONFIG_IS_ENABLED(CMD_FRU) && xilinx_detect_fru(buffer))
return xilinx_read_eeprom_fru(dev, name, desc);
if (xilinx_detect_legacy(buffer))
return xilinx_read_eeprom_legacy(dev, name, desc);
return -ENODEV;
}
__maybe_unused int xilinx_read_eeprom(void)
{
int id;
char name_buf[8]; /* 8 bytes should be enough for nvmem+number */
struct xilinx_board_description *desc;
highest_id = dev_read_alias_highest_id("nvmem");
/* No nvmem aliases present */
if (highest_id < 0)
return -EINVAL;
board_info = calloc(1, sizeof(*desc) * (highest_id + 1));
if (!board_info)
return -ENOMEM;
debug("%s: Highest ID %d, board_info %p\n", __func__,
highest_id, board_info);
for (id = 0; id <= highest_id; id++) {
snprintf(name_buf, sizeof(name_buf), "nvmem%d", id);
/* Alloc structure */
desc = &board_info[id];
/* Ignoring return value for supporting multiple chips */
xilinx_read_eeprom_single(name_buf, desc);
}
/*
* Consider to clean board_info structure when board/cards are not
* detected.
*/
return 0;
}
#if defined(CONFIG_OF_BOARD)
void *board_fdt_blob_setup(int *err)
{
void *fdt_blob;
*err = 0;
if (!IS_ENABLED(CONFIG_SPL_BUILD) &&
!IS_ENABLED(CONFIG_VERSAL_NO_DDR) &&
!IS_ENABLED(CONFIG_ZYNQMP_NO_DDR)) {
fdt_blob = (void *)CONFIG_XILINX_OF_BOARD_DTB_ADDR;
if (fdt_magic(fdt_blob) == FDT_MAGIC)
return fdt_blob;
debug("DTB is not passed via %p\n", fdt_blob);
}
if (IS_ENABLED(CONFIG_SPL_BUILD)) {
/*
* FDT is at end of BSS unless it is in a different memory
* region
*/
if (IS_ENABLED(CONFIG_SPL_SEPARATE_BSS))
fdt_blob = (ulong *)&_image_binary_end;
else
fdt_blob = (ulong *)&__bss_end;
} else {
/* FDT is at end of image */
fdt_blob = (ulong *)&_end;
}
if (fdt_magic(fdt_blob) == FDT_MAGIC)
return fdt_blob;
debug("DTB is also not passed via %p\n", fdt_blob);
*err = -EINVAL;
return NULL;
}
#endif
#if defined(CONFIG_BOARD_LATE_INIT)
static int env_set_by_index(const char *name, int index, char *data)
{
char var[32];
if (!index)
sprintf(var, "board_%s", name);
else
sprintf(var, "card%d_%s", index, name);
return env_set(var, data);
}
int board_late_init_xilinx(void)
{
u32 ret = 0;
int i, id, macid = 0;
struct xilinx_board_description *desc;
phys_size_t bootm_size = gd->ram_top - gd->ram_base;
if (!CONFIG_IS_ENABLED(MICROBLAZE)) {
ulong scriptaddr;
scriptaddr = env_get_hex("scriptaddr", 0);
ret |= env_set_hex("scriptaddr", gd->ram_base + scriptaddr);
}
if (CONFIG_IS_ENABLED(ARCH_ZYNQ) || CONFIG_IS_ENABLED(MICROBLAZE))
bootm_size = min(bootm_size, (phys_size_t)(SZ_512M + SZ_256M));
ret |= env_set_hex("script_offset_f", CONFIG_BOOT_SCRIPT_OFFSET);
ret |= env_set_addr("bootm_low", (void *)gd->ram_base);
ret |= env_set_addr("bootm_size", (void *)bootm_size);
for (id = 0; id <= highest_id; id++) {
desc = &board_info[id];
if (desc && desc->header == EEPROM_HEADER_MAGIC) {
if (desc->manufacturer[0])
ret |= env_set_by_index("manufacturer", id,
desc->manufacturer);
if (desc->name[0])
ret |= env_set_by_index("name", id,
desc->name);
if (desc->revision[0])
ret |= env_set_by_index("rev", id,
desc->revision);
if (desc->serial[0])
ret |= env_set_by_index("serial", id,
desc->serial);
if (desc->uuid[0]) {
char uuid[UUID_STR_LEN + 1];
char *t = desc->uuid;
memset(uuid, 0, UUID_STR_LEN + 1);
sprintf(uuid, "%02x%02x%02x%02x-%02x%02x-%02x%02x-%02x%02x-%02x%02x%02x%02x%02x%02x",
t[0], t[1], t[2], t[3], t[4], t[5],
t[6], t[7], t[8], t[9], t[10], t[11],
t[12], t[13], t[14], t[15]);
ret |= env_set_by_index("uuid", id, uuid);
}
if (!CONFIG_IS_ENABLED(NET))
continue;
for (i = 0; i < EEPROM_HDR_NO_OF_MAC_ADDR; i++) {
if (!desc->mac_addr[i])
break;
if (is_valid_ethaddr((const u8 *)desc->mac_addr[i]))
ret |= eth_env_set_enetaddr_by_index("eth",
macid++, desc->mac_addr[i]);
}
}
}
if (ret)
printf("%s: Saving run time variables FAILED\n", __func__);
return 0;
}
#endif
static char *board_name = DEVICE_TREE;
int __maybe_unused board_fit_config_name_match(const char *name)
{
debug("%s: Check %s, default %s\n", __func__, name, board_name);
if (!strcmp(name, board_name))
return 0;
return -1;
}
#if CONFIG_IS_ENABLED(DTB_RESELECT)
xilinx: common: Enabling generic function for DT reselection U-Boot support board detection at run time and based on it change DT. This feature is implemented for SOM Kria platforms which contain two eeproms which contain information about SOM module and CC (Carrier card). Full U-Boot starts with minimal DT file defined by CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image. It is using default setup of board_name variable initializaed to DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option. When DTB_RESELECT is enabled board_detection() is called. Keep it your mind that this code is called before relocation. board_detection() is calling xilinx_read_eeprom() which fills board_info (xilinx_board_description) structure which are parsed in board_name_decode(). Based on DT configuration and amount of nvmemX aliases name of the board is composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev" <board_revision> "-" <cc_name> "-rev" <cc_revision>. If CC is not present or more are available it keeps going. When board name is composed and returned from board_name_decode() it is assigned to board_name variable which is used by board_fit_config_name_match() which is called via fdtdec_setup() when it goes over config options in multi dtb FIT image. From practical point of view multi DTB image is key point here which has to contain configs for detected combinations. Unfortunately as of now they have to be full DTBs and DTBOs are not supported. That's why configuration like: config_X { description = "zynqmp-board-cc"; fdt = "board", "cc"; }; needs to be squashed together with: fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \ arch/arm/dts/zynqmp-cc.dtbo and only one dtb is in fit: config_X { description = "zynqmp-board-cc"; fdt = "board-cc"; }; For creating multi DTBs fit image use mkimage -E, e.g.: mkimage -E -f all.its all.dtb When DTB_RESELECT is enabled xilinx_read_eeprom() is called before relocation and it uses calloc for getting a buffer. Because this is dynamic memory it is not relocated that's why xilinx_read_eeprom() is called again as the part of board_init(). This second read with calloc buffer placed in proper position board_late_init_xilinx() can setup u-boot variables as before. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-11 12:23:54 +00:00
#define MAX_NAME_LENGTH 50
char * __maybe_unused __weak board_name_decode(void)
{
xilinx: common: Enabling generic function for DT reselection U-Boot support board detection at run time and based on it change DT. This feature is implemented for SOM Kria platforms which contain two eeproms which contain information about SOM module and CC (Carrier card). Full U-Boot starts with minimal DT file defined by CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image. It is using default setup of board_name variable initializaed to DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option. When DTB_RESELECT is enabled board_detection() is called. Keep it your mind that this code is called before relocation. board_detection() is calling xilinx_read_eeprom() which fills board_info (xilinx_board_description) structure which are parsed in board_name_decode(). Based on DT configuration and amount of nvmemX aliases name of the board is composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev" <board_revision> "-" <cc_name> "-rev" <cc_revision>. If CC is not present or more are available it keeps going. When board name is composed and returned from board_name_decode() it is assigned to board_name variable which is used by board_fit_config_name_match() which is called via fdtdec_setup() when it goes over config options in multi dtb FIT image. From practical point of view multi DTB image is key point here which has to contain configs for detected combinations. Unfortunately as of now they have to be full DTBs and DTBOs are not supported. That's why configuration like: config_X { description = "zynqmp-board-cc"; fdt = "board", "cc"; }; needs to be squashed together with: fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \ arch/arm/dts/zynqmp-cc.dtbo and only one dtb is in fit: config_X { description = "zynqmp-board-cc"; fdt = "board-cc"; }; For creating multi DTBs fit image use mkimage -E, e.g.: mkimage -E -f all.its all.dtb When DTB_RESELECT is enabled xilinx_read_eeprom() is called before relocation and it uses calloc for getting a buffer. Because this is dynamic memory it is not relocated that's why xilinx_read_eeprom() is called again as the part of board_init(). This second read with calloc buffer placed in proper position board_late_init_xilinx() can setup u-boot variables as before. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-11 12:23:54 +00:00
char *board_local_name;
struct xilinx_board_description *desc;
int i, id;
board_local_name = calloc(1, MAX_NAME_LENGTH);
if (!board_info)
return NULL;
for (id = 0; id <= highest_id; id++) {
desc = &board_info[id];
/* No board description */
if (!desc)
goto error;
/* Board is not detected */
if (desc->header != EEPROM_HEADER_MAGIC)
continue;
/* The first string should be soc name */
if (!id)
strcat(board_local_name, CONFIG_SYS_BOARD);
/*
* For two purpose here:
* soc_name- eg: zynqmp-
* and between base board and CC eg: ..revA-sck...
*/
strcat(board_local_name, "-");
if (desc->name[0]) {
/* For DT composition name needs to be lowercase */
for (i = 0; i < sizeof(desc->name); i++)
desc->name[i] = tolower(desc->name[i]);
strcat(board_local_name, desc->name);
}
if (desc->revision[0]) {
strcat(board_local_name, "-rev");
/* And revision needs to be uppercase */
for (i = 0; i < sizeof(desc->revision); i++)
desc->revision[i] = toupper(desc->revision[i]);
strcat(board_local_name, desc->revision);
}
}
/*
* Longer strings will end up with buffer overflow and potential
* attacks that's why check it
*/
if (strlen(board_local_name) >= MAX_NAME_LENGTH)
panic("Board name can't be determined\n");
if (strlen(board_local_name))
return board_local_name;
error:
free(board_local_name);
return NULL;
}
bool __maybe_unused __weak board_detection(void)
{
xilinx: common: Enabling generic function for DT reselection U-Boot support board detection at run time and based on it change DT. This feature is implemented for SOM Kria platforms which contain two eeproms which contain information about SOM module and CC (Carrier card). Full U-Boot starts with minimal DT file defined by CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image. It is using default setup of board_name variable initializaed to DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option. When DTB_RESELECT is enabled board_detection() is called. Keep it your mind that this code is called before relocation. board_detection() is calling xilinx_read_eeprom() which fills board_info (xilinx_board_description) structure which are parsed in board_name_decode(). Based on DT configuration and amount of nvmemX aliases name of the board is composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev" <board_revision> "-" <cc_name> "-rev" <cc_revision>. If CC is not present or more are available it keeps going. When board name is composed and returned from board_name_decode() it is assigned to board_name variable which is used by board_fit_config_name_match() which is called via fdtdec_setup() when it goes over config options in multi dtb FIT image. From practical point of view multi DTB image is key point here which has to contain configs for detected combinations. Unfortunately as of now they have to be full DTBs and DTBOs are not supported. That's why configuration like: config_X { description = "zynqmp-board-cc"; fdt = "board", "cc"; }; needs to be squashed together with: fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \ arch/arm/dts/zynqmp-cc.dtbo and only one dtb is in fit: config_X { description = "zynqmp-board-cc"; fdt = "board-cc"; }; For creating multi DTBs fit image use mkimage -E, e.g.: mkimage -E -f all.its all.dtb When DTB_RESELECT is enabled xilinx_read_eeprom() is called before relocation and it uses calloc for getting a buffer. Because this is dynamic memory it is not relocated that's why xilinx_read_eeprom() is called again as the part of board_init(). This second read with calloc buffer placed in proper position board_late_init_xilinx() can setup u-boot variables as before. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-11 12:23:54 +00:00
if (CONFIG_IS_ENABLED(DM_I2C) && CONFIG_IS_ENABLED(I2C_EEPROM)) {
int ret;
ret = xilinx_read_eeprom();
return !ret ? true : false;
}
return false;
}
bool __maybe_unused __weak soc_detection(void)
{
return false;
}
char * __maybe_unused __weak soc_name_decode(void)
{
return NULL;
}
int embedded_dtb_select(void)
{
if (soc_detection()) {
char *soc_local_name;
soc_local_name = soc_name_decode();
if (soc_local_name) {
board_name = soc_local_name;
printf("Detected SOC name: %s\n", board_name);
/* Time to change DTB on fly */
/* Both ways should work here */
/* fdtdec_resetup(&rescan); */
return fdtdec_setup();
}
}
if (board_detection()) {
char *board_local_name;
board_local_name = board_name_decode();
if (board_local_name) {
board_name = board_local_name;
xilinx: common: Enabling generic function for DT reselection U-Boot support board detection at run time and based on it change DT. This feature is implemented for SOM Kria platforms which contain two eeproms which contain information about SOM module and CC (Carrier card). Full U-Boot starts with minimal DT file defined by CONFIG_DEFAULT_DEVICE_TREE which is available in multi DTB fit image. It is using default setup of board_name variable initializaed to DEVICE_TREE which corresponds to CONFIG_DEFAULT_DEVICE_TREE option. When DTB_RESELECT is enabled board_detection() is called. Keep it your mind that this code is called before relocation. board_detection() is calling xilinx_read_eeprom() which fills board_info (xilinx_board_description) structure which are parsed in board_name_decode(). Based on DT configuration and amount of nvmemX aliases name of the board is composed by concatenating CONFIG_SYS_BOARD "-" <board_name> "-rev" <board_revision> "-" <cc_name> "-rev" <cc_revision>. If CC is not present or more are available it keeps going. When board name is composed and returned from board_name_decode() it is assigned to board_name variable which is used by board_fit_config_name_match() which is called via fdtdec_setup() when it goes over config options in multi dtb FIT image. From practical point of view multi DTB image is key point here which has to contain configs for detected combinations. Unfortunately as of now they have to be full DTBs and DTBOs are not supported. That's why configuration like: config_X { description = "zynqmp-board-cc"; fdt = "board", "cc"; }; needs to be squashed together with: fdtoverlay -o zynqmp-board-cc -i arch/arm/dts/zynqmp-board.dtb \ arch/arm/dts/zynqmp-cc.dtbo and only one dtb is in fit: config_X { description = "zynqmp-board-cc"; fdt = "board-cc"; }; For creating multi DTBs fit image use mkimage -E, e.g.: mkimage -E -f all.its all.dtb When DTB_RESELECT is enabled xilinx_read_eeprom() is called before relocation and it uses calloc for getting a buffer. Because this is dynamic memory it is not relocated that's why xilinx_read_eeprom() is called again as the part of board_init(). This second read with calloc buffer placed in proper position board_late_init_xilinx() can setup u-boot variables as before. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-11 12:23:54 +00:00
printf("Detected name: %s\n", board_name);
/* Time to change DTB on fly */
/* Both ways should work here */
/* fdtdec_resetup(&rescan); */
fdtdec_setup();
}
}
return 0;
}
#endif
#if defined(CONFIG_LMB)
phys_size_t board_get_usable_ram_top(phys_size_t total_size)
{
phys_size_t size;
phys_addr_t reg;
struct lmb lmb;
if (!total_size)
return gd->ram_top;
if (!IS_ALIGNED((ulong)gd->fdt_blob, 0x8))
panic("Not 64bit aligned DT location: %p\n", gd->fdt_blob);
/* found enough not-reserved memory to relocated U-Boot */
lmb_init(&lmb);
lmb_add(&lmb, gd->ram_base, gd->ram_size);
boot_fdt_add_mem_rsv_regions(&lmb, (void *)gd->fdt_blob);
size = ALIGN(CONFIG_SYS_MALLOC_LEN + total_size, MMU_SECTION_SIZE);
reg = lmb_alloc(&lmb, size, MMU_SECTION_SIZE);
if (!reg)
reg = gd->ram_top - size;
return reg + size;
}
#endif