Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-18 02:38:56 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/configs/syzygy_hub_defconfig

84 lines
2.1 KiB
Text
Raw Normal View History

arm: zynq: Add support for SYZYGY Hub board Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-09-28 00:53:26 +00:00
CONFIG_ARM=y
CONFIG_SYS_VENDOR="opalkelly"
CONFIG_SYS_CONFIG_NAME="syzygy_hub"
CONFIG_SPL_SYS_[DI]CACHE_OFF: add While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances where these configuration items are conditional on SPL. This commit adds SPL variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates the configurations as required. Acked-by: Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Trevor Woerner <trevor@toganlabs.com> [trini: Make the default depend on the setting for full U-Boot, update more zynq hardware] Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-03 13:41:00 +00:00
CONFIG_SPL_SYS_DCACHE_OFF=y
Convert CONFIG_CONS_INDEX et al to Kconfig This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-11 19:55:51 +00:00
CONFIG_SYS_L2CACHE_OFF=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-26 18:45:25 +00:00
CONFIG_ARCH_ZYNQ=y
arm: zynq: Add support for SYZYGY Hub board Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-09-28 00:53:26 +00:00
CONFIG_SYS_TEXT_BASE=0x4000000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22 18:38:00 +00:00
CONFIG_DM_GPIO=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-06-28 14:17:29 +00:00
CONFIG_DEFAULT_DEVICE_TREE="zynq-syzygy-hub"
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2019-04-29 19:54:04 +00:00
CONFIG_SPL_STACK_R_ADDR=0x200000
xilinx: Sync defconfigs with latest Kconfig updates Make defconfigs up2date with current location. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-03-23 08:34:00 +00:00
CONFIG_SPL=y
xilinx: Sync symbols location in defconfigs CONFIG_DEBUG_UART_BASE and CONFIG_DEBUG_UART_CLOCK have changed that's why this sync. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-04 06:33:30 +00:00
CONFIG_DEBUG_UART_BASE=0xe0000000
CONFIG_DEBUG_UART_CLOCK=50000000
xilinx: common: Move ZYNQ_GEM_I2C_MAC_OFFSET to board Kconfig There is no reason to have ZYNQ specific Kconfig macro in generic location to be visible for all other SoCs. That's why move it to Xilinx common location to be visible only for us. Also introduce new bool entry ZYNQ_MAC_IN_EEPROM to have also an option to disable it or enable. This has connection to code which is reading the whole content of i2c and also work with the rest of date not just with MAC address. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-10-14 15:08:14 +00:00
CONFIG_ZYNQ_MAC_IN_EEPROM=y
CONFIG_ZYNQ_GEM_I2C_MAC_OFFSET=0xFA
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 17:36:51 +00:00
CONFIG_SYS_LOAD_ADDR=0x0
arm: zynq: Add support for SYZYGY Hub board Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-09-28 00:53:26 +00:00
CONFIG_DEBUG_UART=y
arm: zynq: Enable distro defaults setting BOOTCOMMAND is composed with distro_bootcmd but this variable is not present. Enabling distro defaults setting is fixing it. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-09 18:31:16 +00:00
CONFIG_DISTRO_DEFAULTS=y
Convert CONFIG_REMAKE_ELF to Kconfig This converts the following to Kconfig: CONFIG_REMAKE_ELF Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
2022-01-29 15:25:30 +00:00
CONFIG_REMAKE_ELF=y
configs: Migrate CONFIG_SYS_LDSCRIPT to Kconfig In order to migrate this symbol to Kconfig introduce a new symbol to guard it, CONFIG_SYS_CUSTOM_LDSCRIPT. When that is set we can then provide the exact final location o the script. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-06-02 12:57:32 +00:00
CONFIG_SYS_CUSTOM_LDSCRIPT=y
CONFIG_SYS_LDSCRIPT="arch/arm/mach-zynq/u-boot.lds"
arm: zynq: Add support for SYZYGY Hub board Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-09-28 00:53:26 +00:00
CONFIG_FIT=y
CONFIG_FIT_SIGNATURE=y
CONFIG_FIT_VERBOSE=y
configs: Rename CONFIG_IMAGE_FORMAT_LEGACY to CONFIG_LEGACY_IMAGE_FORMAT The name CONFIG_LEGACY_IMAGE_FORMAT reads slightly better along with allowing us to avoid a rather nasty Kbuild/Kconfig issue down the line with CONFIG_IS_ENABLED(IMAGE_FORMAT_LEGACY). In a few places outside of cmd/ switch to using CONFIG_IS_ENABLED() to test what is set. Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-23 11:14:07 +00:00
CONFIG_LEGACY_IMAGE_FORMAT=y
Convert CONFIG_USE_PREBOOT and CONFIG_PREBOOT to Kconfig This converts the following to Kconfig: CONFIG_USE_PREBOOT CONFIG_PREBOOT Both are together in one commit, since otherwise the former causes kconfig to define the latter, which gives duplicate symbol errors. Includes a manual fixup for CONFIG_PREBOOT in ids8313_defconfig since the backslash lands in the wrong place. Similarly with socfpga_vining_fpga. Signed-off-by: Simon Glass <sjg@chromium.org>
2019-07-21 02:51:14 +00:00
CONFIG_USE_PREBOOT=y
Convert CONFIG_CLOCKS to Kconfig This converts the following to Kconfig: CONFIG_CLOCKS Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-23 21:20:08 +00:00
CONFIG_CLOCKS=y
Convert CONFIG_SPL_PAD_TO et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE CONFIG_TPL_PAD_TO CONFIG_TPL_MAX_SIZE Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the existing places. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-16 21:20:26 +00:00
CONFIG_SPL_MAX_SIZE=0x30000
Convert CONFIG_SPL_BSS_START_ADDR to Kconfig This converts the following to Kconfig: CONFIG_SPL_BSS_START_ADDR Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-27 14:19:45 +00:00
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
CONFIG_SPL_BSS_START_ADDR=0x100000
Convert CONFIG_SPL_BSS_MAX_SIZE et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_BSS_MAX_SIZE CONFIG_SPL_MAX_FOOTPRINT Note that the da850evm platforms were violating the "only use one" rule here, and so now hard-code their BSS limit. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-19 19:09:22 +00:00
CONFIG_SPL_BSS_MAX_SIZE=0x100000
Convert CONFIG_SPL_STACK to Kconfig This converts the following to Kconfig: CONFIG_SPL_STACK Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-26 17:13:21 +00:00
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
CONFIG_SPL_STACK=0xfffffe00
arm: zynq: Fix SPL SD boot mode This patch is fixing two issues: 1. Insufficient stack size for fat fs buffers 2. Insufficient space in malloc area Tested on zc702 and zc706. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-12-01 12:50:33 +00:00
CONFIG_SPL_STACK_R=y
Convert CONFIG_SYS_SPL_MALLOC_SIZE et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_SPL_MALLOC_START We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to control if we have a malloc pool or not. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-27 16:48:32 +00:00
CONFIG_SYS_SPL_MALLOC=y
CONFIG_SYS_SPL_MALLOC_SIZE=0x2000000
Convert CONFIG_SPL_FS_LOAD_PAYLOAD_NAME et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_FS_LOAD_ARGS_NAME CONFIG_SPL_FS_LOAD_KERNEL_NAME CONFIG_SPL_FS_LOAD_PAYLOAD_NAME Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-13 21:12:35 +00:00
CONFIG_SPL_FS_LOAD_ARGS_NAME="system.dtb"
arm: zynq: Add support for SYZYGY Hub board Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-09-28 00:53:26 +00:00
CONFIG_SPL_OS_BOOT=y
Convert CONFIG_SYS_SPL_ARGS_ADDR to Kconfig This converts the following to Kconfig: CONFIG_SYS_SPL_ARGS_ADDR In doing so, we also consistently use this variable for SPL_OS_BOOT and not CONFIG_SYS_FDT_BASE in some cases. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-28 02:06:52 +00:00
CONFIG_SYS_SPL_ARGS_ADDR=0x10000000
Convert CONFIG_SYS_MAXARGS to Kconfig This converts the following to Kconfig: CONFIG_SYS_MAXARGS Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-11 20:21:06 +00:00
CONFIG_SYS_MAXARGS=32
Convert CONFIG_SYS_PBSIZE to Kconfig This converts the following to Kconfig: CONFIG_SYS_PBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-11 21:38:09 +00:00
CONFIG_SYS_PBSIZE=2071
arm: zynq: Add support for SYZYGY Hub board Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-09-28 00:53:26 +00:00
CONFIG_CMD_FPGA_LOADBP=y
CONFIG_CMD_FPGA_LOADFS=y
CONFIG_CMD_FPGA_LOADMK=y
CONFIG_CMD_FPGA_LOADP=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
CONFIG_CMD_USB=y
# CONFIG_CMD_SETEXPR is not set
Convert CONFIG_BOOTP_MAY_FAIL et al to Kconfig This converts the following to Kconfig: CONFIG_BOOTP_MAY_FAIL CONFIG_BOOTP_VENDOREX CONFIG_BOOTP_BOOTFILESIZE CONFIG_BOOTP_NISDOMAIN CONFIG_BOOTP_TIMEOFFSET Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-02-25 16:19:50 +00:00
CONFIG_BOOTP_MAY_FAIL=y
arm: zynq: Add support for SYZYGY Hub board Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-09-28 00:53:26 +00:00
CONFIG_CMD_TFTPPUT=y
CONFIG_CMD_CACHE=y
CONFIG_CMD_EXT4_WRITE=y
Convert CONFIG_ENV_OVERWRITE to Kconfig This converts the following to Kconfig: CONFIG_ENV_OVERWRITE Signed-off-by: Adam Ford <aford173@gmail.com> [trini: Rerun migration, remove some comments] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-03 11:48:56 +00:00
CONFIG_ENV_OVERWRITE=y
env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-13 03:46:36 +00:00
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
Convert CONFIG_SYS_FAULT_ECHO_LINK_DOWN to Kconfig This converts the following to Kconfig: CONFIG_SYS_FAULT_ECHO_LINK_DOWN Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18 12:38:21 +00:00
CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
arm: zynq: Add support for SYZYGY Hub board Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-09-28 00:53:26 +00:00
CONFIG_SPL_DM_SEQ_ALIAS=y
arm: zynq: Enable FPGA/FPGA_XILINX via Kconfig Enabling fpga via Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-11-03 14:53:56 +00:00
CONFIG_FPGA_XILINX=y
arm: zynq: fpga: Added Kconfig support for CONFIG_FPGA_ZYNQPL This patch added Kconfig support for CONFIG_FPGA_ZYNQPL and migrates the values over to the defconfigs. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
2018-02-16 12:32:51 +00:00
CONFIG_FPGA_ZYNQPL=y
ARM: zynq: Convert Syzygy to DM_I2C Boards have only one controller enabled that's why move to DM_I2C is easy. Add also i2c alias for not to be shown as i2c bus -1 because alias doesn't exist. Config file points to MAC stored in eeprom but it is not listed that's why I have added 24c08 part. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Heiko Schocher <hs@denx.de>
2019-01-22 13:12:54 +00:00
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_CADENCE=y
arm: zynq: Add support for SYZYGY Hub board Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-09-28 00:53:26 +00:00
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
arm: zynq: Moved ethernet PHY configs of Zynq boards to defconfig This patch moved ethernet PHY configs of Zynq boards to respective defconfig. Signed-off-by: Vipul Kumar <vipulk@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-01-24 05:21:30 +00:00
CONFIG_PHY_MARVELL=y
CONFIG_PHY_REALTEK=y
CONFIG_PHY_XILINX=y
Convert CONFIG_MII et al to Kconfig This converts the following to Kconfig: CONFIG_MII CONFIG_DRIVER_TI_EMAC Signed-off-by: Adam Ford <aford173@gmail.com> Acked-by: Jagan Teki <jagan@amarulasolutions.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com>
2018-07-21 04:03:57 +00:00
CONFIG_MII=y
arm: zynq: Add support for SYZYGY Hub board Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-09-28 00:53:26 +00:00
CONFIG_ZYNQ_GEM=y
CONFIG_DEBUG_UART_ZYNQ=y
serial: Convert ARM_DCC to Kconfig The symbol "CONFIG_ARM_DCC" is used to control building drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this. Cc: Luca Ceresoli <luca@lucaceresoli.net> Cc: Michal Simek <monstr@monstr.eu> Cc: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2020-06-02 21:26:33 +00:00
CONFIG_ARM_DCC=y
arm: zynq: Move ZYNQ_SERIAL to Kconfig Move cadence/zynq serial driver via Kconfig Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2017-11-06 08:16:05 +00:00
CONFIG_ZYNQ_SERIAL=y
arm: zynq: Add support for SYZYGY Hub board Add the Zynq-based SYZYGY Hub board from Opal Kelly. The board contains a Xilinx Zynq xc7z012s SoC, 1GB DDR3 RAM, and supports booting from SD. Signed-off-by: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Michal Simek <monstr@monstr.eu> CC: Albert Aribaud <albert.u.boot@aribaud.net> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2017-09-28 00:53:26 +00:00
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_ULPI_VIEWPORT=y
CONFIG_USB_ULPI=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_MANUFACTURER="Xilinx"
CONFIG_USB_GADGET_VENDOR_NUM=0x03FD
CONFIG_USB_GADGET_PRODUCT_NUM=0x0300
CONFIG_CI_UDC=y
CONFIG_USB_GADGET_DOWNLOAD=y
Kconfig: gadget: Move CONFIG_USB_FUNCTION_THOR to Kconfig This commit moves USB_FUNCTION_THOR config to Kconfig. Signed-off-by: Lukasz Majewski <lukma@denx.de> Acked-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
2018-01-29 18:30:18 +00:00
CONFIG_USB_FUNCTION_THOR=y
Reference in a new issue Copy permalink