Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-14 08:57:58 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/configs/xilinx_zynq_virt_defconfig

154 lines
3.9 KiB
Text
Raw Normal View History

ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_ARM=y
CONFIG_SPL_SYS_DCACHE_OFF=y
Convert CONFIG_CONS_INDEX et al to Kconfig This converts the following to Kconfig: CONFIG_CONS_INDEX CONFIG_DEBUG_UART_CLOCK CONFIG_FSL_TZPC_BP147 CONFIG_GENERIC_ATMEL_MCI CONFIG_IDENT_STRING CONFIG_LIBATA CONFIG_LNX_KRNL_IMG_TEXT_OFFSET_BASE CONFIG_LPC32XX_GPIO CONFIG_MP CONFIG_MPC8XXX_GPIO CONFIG_MTD_PARTITIONS CONFIG_MVGBE CONFIG_MXC_GPIO CONFIG_NR_DRAM_BANKS CONFIG_OF_BOARD_SETUP CONFIG_OF_STDOUT_VIA_ALIAS CONFIG_OF_SYSTEM_SETUP CONFIG_PREBOOT CONFIG_ROCKCHIP_SERIAL CONFIG_RTC_ENABLE_32KHZ_OUTPUT CONFIG_RTC_MV CONFIG_SCSI_AHCI CONFIG_SF_DEFAULT_BUS CONFIG_SF_DEFAULT_CS CONFIG_SF_DEFAULT_SPEED CONFIG_SOFT_SPI CONFIG_SPI_FLASH_EON CONFIG_SPI_FLASH_MACRONIX CONFIG_SPI_FLASH_MTD CONFIG_SPI_FLASH_SPANSION CONFIG_SPI_FLASH_SST CONFIG_SPI_FLASH_STMICRO CONFIG_SUPPORT_RAW_INITRD CONFIG_SYS_ARCH_TIMER CONFIG_SYS_BOARD CONFIG_SYS_CONSOLE_OVERWRITE_ROUTINE CONFIG_SYS_DCACHE_OFF CONFIG_SYS_FDT_SAVE_ADDRESS CONFIG_SYS_FLASH_CFI CONFIG_SYS_FSL_ERRATUM_ESDHC135 CONFIG_SYS_HAS_SERDES CONFIG_SYS_L2CACHE_OFF CONFIG_SYS_LITTLE_ENDIAN CONFIG_SYS_LOAD_ADDR CONFIG_SYS_MMCSD_FS_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_PARTITION CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR CONFIG_SYS_NS16550 CONFIG_SYS_PLLFIN CONFIG_SYS_SPI_U_BOOT_OFFS CONFIG_TIMER_SYS_TICK_CH CONFIG_USB_EHCI_FSL CONFIG_U_QE CONFIG_VERSION_VARIABLE Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-11 19:55:51 +00:00
CONFIG_SYS_L2CACHE_OFF=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_ARCH_ZYNQ=y
CONFIG_SYS_TEXT_BASE=0x4000000
xilinx: zynq: Add support for saving env based on bootmode Enable saving variables to MMC(FAT), NAND, SPI based on primary bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE). Since most of the flashes on zynq evaluation boards are 16MB in size, set default ENV_OFFSET to 15MB(0xE00000). Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-02-23 15:07:45 +00:00
CONFIG_ENV_OFFSET=0xE00000
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2020-01-22 18:38:00 +00:00
CONFIG_DM_GPIO=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-06-28 14:17:29 +00:00
CONFIG_DEFAULT_DEVICE_TREE="zynq-zc706"
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_SPL_STACK_R_ADDR=0x200000
CONFIG_SPL=y
xilinx: Add env redund offset ENV_OFFSET_REDUND config is by default set to 0 for flashes. Saving the env variables is overwriting data at 0 offset, which is wrong. So add default redund env offset for Zynq, ZynqMP, Versal and microblaze platforms. Configured ENV_OFFSET_REDUND offsets by ENV_OFFSET + (2 * ENV_SIZE). In case of versal, we configured ENV_OFFSET_REDUND at 0x7F00000 instead of 0x7F80000. As BOOT_SCRIPT_OFFSET is already configured at 0x7F80000. Added ENV_OFFSET_REDUND in Kconfig for microblaze due to dependency of ENV_IS_IN_SPI_FLASH config. Below table specifies platform specific env and env redund offsets. PLAT ENV_OFFSET ENV_OFFSET_REDUND ---- ---------- ----------------- ZYNQ 0xE0000 0xE40000 ZYNQMP 0x1E00000 0x1E80000 VERSAL 0x7F40000 0x7F00000 MICROBLAZE 0x1080000 0x10C0000 Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/92656dc08f0f5a749d62b71ca6e77fe1be72e9e0.1661340204.git.michal.simek@amd.com
2022-08-24 11:23:26 +00:00
CONFIG_ENV_OFFSET_REDUND=0xE40000
xilinx: Enable FRU command for all ARM based platforms Enable it by default for board detection. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-10-22 08:33:29 +00:00
CONFIG_CMD_FRU=y
xilinx: zynq: Enable AES command Enable AES command to be able to use it directly. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-10-22 08:34:00 +00:00
CONFIG_CMD_ZYNQ_AES=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-08 17:36:51 +00:00
CONFIG_SYS_LOAD_ADDR=0x0
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2022-04-01 14:33:18 +00:00
CONFIG_SYS_MEMTEST_START=0x00000000
CONFIG_SYS_MEMTEST_END=0x00001000
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_DISTRO_DEFAULTS=y
Convert CONFIG_REMAKE_ELF to Kconfig This converts the following to Kconfig: CONFIG_REMAKE_ELF Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
2022-01-29 15:25:30 +00:00
CONFIG_REMAKE_ELF=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_SYS_CUSTOM_LDSCRIPT=y
CONFIG_SYS_LDSCRIPT="arch/arm/mach-zynq/u-boot.lds"
CONFIG_FIT=y
CONFIG_FIT_SIGNATURE=y
CONFIG_FIT_VERBOSE=y
ARM: zynq: Switch to single zynq configurations There are a lot of zynq configurations which can be merged together and use only one for all. The similar change has been done for ZynqMP by commit be1b6c32d940 ("arm64: zynqmp: Use zynqmp_virt platform") Build SPL with u-boot.img for zc706 like this. export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8 u-boot.img is generic for all boards. Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-13 14:03:29 +00:00
CONFIG_SPL_FIT_PRINT=y
CONFIG_SPL_LOAD_FIT=y
configs: migrate CONFIG_SPL_LOAD_FIT_ADDRESS to defconfigs Done with: ./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS ./tools/moveconfig.py -S SPL_LOAD_FIT_ADDRESS -H Signed-off-by: Peng Fan <peng.fan@nxp.com> [trini: A few more migrations] Signed-off-by: Tom Rini <trini@konsulko.com>
2020-07-06 07:35:01 +00:00
CONFIG_SPL_LOAD_FIT_ADDRESS=0x10000000
Makefile: Allow CONFIG_SPL_FIT_GENERATOR to be empty At present we use the empty string to indicate that there is no FIT generator, but this doesn't allow an individual board to undefine it. Create a separate bool instead. Update the config of the boards which currently have an empty string. Signed-off-by: Simon Glass <sjg@chromium.org>
2020-07-19 19:56:10 +00:00
# CONFIG_USE_SPL_FIT_GENERATOR is not set
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_LEGACY_IMAGE_FORMAT=y
xilinx: Disable ARCH_FIXUP_FDT_MEMORY Based on DT spec you can have one memory node which multiple ranges or multiple nodes. fdt_fixup_memory_banks() is not implemented in a correct way when multiple memory nodes are present because all ranges are put it to the first memory node found. And next memory nodes are kept in DT which ends up in the same range specification in the same DT. Here is what it is happening. Origin DT. memory@0 { device_type = "memory"; reg = <0x0 0x0 0x0 0x80000000>; }; memory@800000000 { device_type = "memory"; reg = <0x8 0x00000000 0x0 0x80000000>; }; After fdt_fixup_memory_banks() memory@0 { device_type = "memory"; reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>; }; memory@800000000 { device_type = "memory"; reg = <0x8 0x00000000 0x0 0x80000000>; }; As is visible memory@0 node got second range but there is still memory@800000000 node present and 2G range is listed twice. The solution can't be that second node is removed because it can be referenced already that's why it is better for us to disable this option for now. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-08-06 12:09:32 +00:00
# CONFIG_ARCH_FIXUP_FDT_MEMORY is not set
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_USE_PREBOOT=y
Convert CONFIG_CLOCKS to Kconfig This converts the following to Kconfig: CONFIG_CLOCKS Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-23 21:20:08 +00:00
CONFIG_CLOCKS=y
Convert CONFIG_SPL_PAD_TO et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_PAD_TO CONFIG_SPL_MAX_SIZE CONFIG_TPL_PAD_TO CONFIG_TPL_MAX_SIZE Note that we need to make TPL_MAX_SIZE be hex, and so move and convert the existing places. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-16 21:20:26 +00:00
CONFIG_SPL_MAX_SIZE=0x30000
Convert CONFIG_SPL_BSS_START_ADDR to Kconfig This converts the following to Kconfig: CONFIG_SPL_BSS_START_ADDR Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-27 14:19:45 +00:00
CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
CONFIG_SPL_BSS_START_ADDR=0x100000
Convert CONFIG_SPL_BSS_MAX_SIZE et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_BSS_MAX_SIZE CONFIG_SPL_MAX_FOOTPRINT Note that the da850evm platforms were violating the "only use one" rule here, and so now hard-code their BSS limit. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-19 19:09:22 +00:00
CONFIG_SPL_BSS_MAX_SIZE=0x100000
Convert CONFIG_SPL_STACK to Kconfig This converts the following to Kconfig: CONFIG_SPL_STACK Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-26 17:13:21 +00:00
# CONFIG_SPL_SHARES_INIT_SP_ADDR is not set
CONFIG_SPL_STACK=0xfffffe00
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_SPL_STACK_R=y
Convert CONFIG_SYS_SPL_MALLOC_SIZE et al to Kconfig This converts the following to Kconfig: CONFIG_SYS_SPL_MALLOC_SIZE CONFIG_SYS_SPL_MALLOC_START We introduce a default value here as well, and CONFIG_SYS_SPL_MALLOC to control if we have a malloc pool or not. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-27 16:48:32 +00:00
CONFIG_SYS_SPL_MALLOC=y
CONFIG_SYS_SPL_MALLOC_SIZE=0x2000000
Convert CONFIG_SPL_FS_LOAD_PAYLOAD_NAME et al to Kconfig This converts the following to Kconfig: CONFIG_SPL_FS_LOAD_ARGS_NAME CONFIG_SPL_FS_LOAD_KERNEL_NAME CONFIG_SPL_FS_LOAD_PAYLOAD_NAME Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-13 21:12:35 +00:00
CONFIG_SPL_FS_LOAD_PAYLOAD_NAME="u-boot.img"
CONFIG_SPL_FS_LOAD_ARGS_NAME="system.dtb"
fpga: kconfig: Rename SPL_FPGA_SUPPORT to SPL_FPGA The patch does sed 's/SPL_FPGA_SUPPORT/SPL_FPGA/g' but also fixing Makefile and zynqmp.c to simplify if/endif logic in zynqmp.c. This change is mostly done to be able to use CONFIG_IS_ENABLED macro and obj-$(CONFIG_$(SPL_)FPGA) in Makefile. For them symbols need to be in sync. And removing one line from Topic Miami boards which is not needed because symbol is not enabled via Kconfig. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Reviewed-by: Simon Glass <sjg@chromium.org>
2020-09-09 12:41:56 +00:00
CONFIG_SPL_FPGA=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_SPL_OS_BOOT=y
Convert CONFIG_SYS_SPL_ARGS_ADDR to Kconfig This converts the following to Kconfig: CONFIG_SYS_SPL_ARGS_ADDR In doing so, we also consistently use this variable for SPL_OS_BOOT and not CONFIG_SYS_FDT_BASE in some cases. Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-28 02:06:52 +00:00
CONFIG_SYS_SPL_ARGS_ADDR=0x10000000
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_SPL_SPI_LOAD=y
configs: Resync with savedefconfig Rsync all defconfig files using moveconfig.py Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-10 19:08:46 +00:00
CONFIG_SYS_SPI_U_BOOT_OFFS=0x100000
Convert CONFIG_SYS_MAXARGS to Kconfig This converts the following to Kconfig: CONFIG_SYS_MAXARGS Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-11 20:21:06 +00:00
CONFIG_SYS_MAXARGS=32
Convert CONFIG_SYS_PBSIZE to Kconfig This converts the following to Kconfig: CONFIG_SYS_PBSIZE Signed-off-by: Tom Rini <trini@konsulko.com>
2022-05-11 21:38:09 +00:00
CONFIG_SYS_PBSIZE=2071
ARM: zynq: Move BOOTM_NETBSD to Kconfig The commit 4b0bcfa7c4ec ("Kconfig: Migrate CONFIG_BOOTM_* options") moved BOOTM_ options to Kconfig that's why align zynq defconfig with it. Disabling NETBSD was done by commit d6f48ea5ce18 ("ARM: zynq: Do not enable NETBSD support by default"). Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-14 07:38:39 +00:00
# CONFIG_BOOTM_NETBSD is not set
Convert CONFIG_SYS_BOOTM_LEN to Kconfig This converts the following to Kconfig: CONFIG_SYS_BOOTM_LEN As part of this, rework error handling in boot/bootm.c so that we pass the buffer size to handle_decomp_error as CONFIG_SYS_BOOTM_LEN will not be available to host tools but we do know the size that we passed to malloc(). Cc: Soeren Moch <smoch@web.de> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-25 23:29:46 +00:00
CONFIG_SYS_BOOTM_LEN=0x3c00000
ARM: zynq: Switch to single zynq configurations There are a lot of zynq configurations which can be merged together and use only one for all. The similar change has been done for ZynqMP by commit be1b6c32d940 ("arm64: zynqmp: Use zynqmp_virt platform") Build SPL with u-boot.img for zc706 like this. export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8 u-boot.img is generic for all boards. Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-13 14:03:29 +00:00
CONFIG_CMD_IMLS=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_CMD_THOR_DOWNLOAD=y
xilinx: Enable CMD_GREPENV/SETEXPR by default Enable both of these commands in Xilinx SoCs to be able to use them in boot scripts. Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/1a612be7e09e9bc502f30e1f025441ccf8accba5.1661340513.git.michal.simek@amd.com
2022-08-24 11:28:35 +00:00
CONFIG_CMD_GREPENV=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_CMD_MEMTEST=y
arm: zynq: Enable alternative memory test Enable alternative memory test for zynq platforms. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-05-01 05:44:23 +00:00
CONFIG_SYS_ALT_MEMTEST=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_CMD_DFU=y
CONFIG_CMD_FPGA_LOADBP=y
CONFIG_CMD_FPGA_LOADFS=y
CONFIG_CMD_FPGA_LOADMK=y
CONFIG_CMD_FPGA_LOADP=y
CONFIG_CMD_GPIO=y
CONFIG_CMD_I2C=y
CONFIG_CMD_MMC=y
xilinx: Enable MTD and UBIFS for zynq and zynqmp Both of them have nand controller that's why it is good to enable it because these configurations are also covered by testing. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-08 08:37:51 +00:00
CONFIG_CMD_MTD=y
ARM: zynq: Switch to single zynq configurations There are a lot of zynq configurations which can be merged together and use only one for all. The similar change has been done for ZynqMP by commit be1b6c32d940 ("arm64: zynqmp: Use zynqmp_virt platform") Build SPL with u-boot.img for zc706 like this. export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8 u-boot.img is generic for all boards. Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-13 14:03:29 +00:00
CONFIG_CMD_NAND_LOCK_UNLOCK=y
xilinx: Enable SF_TEST command for all ARM based platforms Enable this command by default. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-10-22 08:34:43 +00:00
CONFIG_CMD_SF_TEST=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_CMD_USB=y
Convert CONFIG_BOOTP_MAY_FAIL et al to Kconfig This converts the following to Kconfig: CONFIG_BOOTP_MAY_FAIL CONFIG_BOOTP_VENDOREX CONFIG_BOOTP_BOOTFILESIZE CONFIG_BOOTP_NISDOMAIN CONFIG_BOOTP_TIMEOFFSET Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-02-25 16:19:50 +00:00
CONFIG_BOOTP_MAY_FAIL=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_CMD_TFTPPUT=y
CONFIG_CMD_CACHE=y
ARM: zynq: Enable capsule update for qspi and mmc Generate dfu_alt_info setup at runtime for capsule update. Enabling this feature will help with upgrading boards without remembering what is where. The similar change was done for ZynqMP by commit b86f43de0be0 ("xilinx: zynqmp: Add support for runtime dfu_alt_info setup"). Code needs to be enabled by CONFIG_SET_DFU_ALT_INFO. And also enable capsule on disk for RAW firmware images with efidebug command. Two indexes are supported for SPL flow. Images can be generated like: ./tools/mkeficapsule --raw spl/boot.bin --index 1 capsule1.bin ./tools/mkeficapsule --raw u-boot.img --index 2 capsule2.bin Then place them to SD card and load them: load mmc 0 10000000 capsule1.bin && efidebug capsule update -v 10000000 load mmc 0 10000000 capsule2.bin && efidebug capsule update -v 10000000 FSBL flow will also work where only index 1 capsule is used. There should be enough space for using boot.bin with bitstream too. Zynq also support multiple boot locations in SPI or MMC but it is not wired by this patch. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/bea5fc75a87a5971f118b46bab4aa7ca39a629c6.1630061610.git.michal.simek@xilinx.com
2021-08-27 10:53:32 +00:00
CONFIG_CMD_EFIDEBUG=y
xilinx: zynq: Enable time and timer commands Enable time command to get the elapsed time and timer commands. Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-02-04 07:39:01 +00:00
CONFIG_CMD_TIME=y
CONFIG_CMD_TIMER=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_CMD_EXT4_WRITE=y
xilinx: Enable support for SquashFS Enable SquashFS for all xilinx platforms. Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/dbe85afda8cd90ebfc537979d382808ff9bec160.1655982259.git.michal.simek@amd.com
2022-06-23 11:04:21 +00:00
CONFIG_CMD_SQUASHFS=y
xilinx: Enable MTD and UBIFS for zynq and zynqmp Both of them have nand controller that's why it is good to enable it because these configurations are also covered by testing. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-08 08:37:51 +00:00
CONFIG_CMD_MTDPARTS=y
CONFIG_CMD_MTDPARTS_SPREAD=y
CONFIG_CMD_MTDPARTS_SHOW_NET_SIZES=y
CONFIG_CMD_UBI=y
xilinx: Enable OF_BOARD for zynq and zynqmp boards The commit 985503439762 ("fdt: Don't call board_fdt_blob_setup() without OF_BOARD") forced to enable OF_BOARD for platforms which provide DT externally. Zynq/ZynqMP boards are using this feature for a long time that's why there is a need to enable it by default. Also code expects to return error in case of error that's why also fill it. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/9f11bbffe2849f4da7d72712082d579262fe8fd8.1645104518.git.michal.simek@xilinx.com
2022-02-17 13:28:38 +00:00
CONFIG_OF_BOARD=y
ARM: zynq: Add Z-turn board V5 Adding Z-turn board V5 to resolve the change between: "Z-TURNBOARD_schematic.pdf" schematics state version 1 to 4 has Atheros AR8035 "Z-Turn_Board_sch_V15_20160303.pdf" schematics state version 5 has Micrel KSZ9031 At this time the S25FL128SAGNFI003 doesn't work because of bug: *** Warning - spi_flash_probe_bus_cs() failed, using default environment zynq-zturn was checked on V5 board, same error. Maybe Z-turn board have the same problem (board with W25Q128BVFIG). Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-10-01 08:33:36 +00:00
CONFIG_OF_LIST="zynq-zc702 zynq-zc706 zynq-zc770-xm010 zynq-zc770-xm011 zynq-zc770-xm011-x16 zynq-zc770-xm012 zynq-zc770-xm013 zynq-cc108 zynq-microzed zynq-minized zynq-picozed zynq-zed zynq-zturn zynq-zturn-v5 zynq-zybo zynq-zybo-z7 zynq-dlc20-rev1.0"
xilinx: zynq: Add support for saving env based on bootmode Enable saving variables to MMC(FAT), NAND, SPI based on primary bootmode. If bootmode is JTAG, dont save env anywhere(NOWHERE). Since most of the flashes on zynq evaluation boards are 16MB in size, set default ENV_OFFSET to 15MB(0xE00000). Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-02-23 15:07:45 +00:00
CONFIG_ENV_IS_NOWHERE=y
CONFIG_ENV_IS_IN_FAT=y
CONFIG_ENV_IS_IN_NAND=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_ENV_IS_IN_SPI_FLASH=y
xilinx: Enable redundant variable handling Enable this feature by default to be able to work with env import/export commands which are done in this slightly changed variable format (There is addtional flag fields in variable file which is changing CRC calculation). Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-02-24 09:44:20 +00:00
CONFIG_SYS_REDUNDAND_ENVIRONMENT=y
env: Add CONFIG_SYS_RELOC_GD_ENV_ADDR symbol Today in initr_reloc_global_data() we use some non-obvious tests to determine if we need to relocate the env_addr within gd or not. In order to facilitate migration of other symbols to Kconfig we need to introduce a new symbol for this particular use case. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2019-11-13 03:46:36 +00:00
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_NET_RANDOM_ETHADDR=y
arm64: zynqmp: Enable netconsole for ZynqMP It is nice feature Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-03-18 08:19:02 +00:00
CONFIG_NETCONSOLE=y
Convert CONFIG_SYS_FAULT_ECHO_LINK_DOWN to Kconfig This converts the following to Kconfig: CONFIG_SYS_FAULT_ECHO_LINK_DOWN Cc: Ramon Fried <rfried.dev@gmail.com> Signed-off-by: Tom Rini <trini@konsulko.com>
2022-03-18 12:38:21 +00:00
CONFIG_SYS_FAULT_ECHO_LINK_DOWN=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_SPL_DM_SEQ_ALIAS=y
xilinx: Enable DFU_TIMEOUT config Enable CONFIG_DFU_TIMEOUT to set timeout waiting for dfu command. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-31 05:24:59 +00:00
CONFIG_DFU_TIMEOUT=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_DFU_MMC=y
CONFIG_DFU_RAM=y
ARM: zynq: Enable capsule update for qspi and mmc Generate dfu_alt_info setup at runtime for capsule update. Enabling this feature will help with upgrading boards without remembering what is where. The similar change was done for ZynqMP by commit b86f43de0be0 ("xilinx: zynqmp: Add support for runtime dfu_alt_info setup"). Code needs to be enabled by CONFIG_SET_DFU_ALT_INFO. And also enable capsule on disk for RAW firmware images with efidebug command. Two indexes are supported for SPL flow. Images can be generated like: ./tools/mkeficapsule --raw spl/boot.bin --index 1 capsule1.bin ./tools/mkeficapsule --raw u-boot.img --index 2 capsule2.bin Then place them to SD card and load them: load mmc 0 10000000 capsule1.bin && efidebug capsule update -v 10000000 load mmc 0 10000000 capsule2.bin && efidebug capsule update -v 10000000 FSBL flow will also work where only index 1 capsule is used. There should be enough space for using boot.bin with bitstream too. Zynq also support multiple boot locations in SPI or MMC but it is not wired by this patch. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/bea5fc75a87a5971f118b46bab4aa7ca39a629c6.1630061610.git.michal.simek@xilinx.com
2021-08-27 10:53:32 +00:00
CONFIG_DFU_SF=y
usb: dfu: Migrate CONFIG_SYS_DFU_DATA_BUF_SIZE and CONFIG_SYS_DFU_MAX_FILE_SIZE to Kconfig Currently the config options CONFIG_SYS_DFU_DATA_BUF_SIZE and CONFIG_SYS_DFU_MAX_FILE_SIZE are being set in include/configs/<board>.h files and also in <board_name>_defconfig files without a Kconfig option. It is easier for users to set these configs in defconfig files than in config header files as they are a part of the source code. Add Kconfig symbols, and update the defconfigs by using tools/moveconfig.py script. Suggested-by: Pratyush Yadav <p.yadav@ti.com> Signed-off-by: Aswath Govindraju <a-govindraju@ti.com> Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com> Acked-by: Matthias Brugger <mbrugger@suse.com> Acked-by: Lukasz Majewski <lukma@denx.de>
2021-06-01 11:21:47 +00:00
CONFIG_SYS_DFU_DATA_BUF_SIZE=0x600000
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_FPGA_XILINX=y
CONFIG_FPGA_ZYNQPL=y
CONFIG_DM_I2C=y
CONFIG_SYS_I2C_CADENCE=y
ARM: zynq: Enable i2c mux support for all boards zc702/zc706 have pca9548 i2c muxes that's why enable the driver by default. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-03-05 07:17:49 +00:00
CONFIG_I2C_MUX=y
CONFIG_I2C_MUX_PCA954x=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_LED=y
CONFIG_LED_GPIO=y
CONFIG_MISC=y
CONFIG_I2C_EEPROM=y
CONFIG_MMC_SDHCI=y
CONFIG_MMC_SDHCI_ZYNQ=y
ARM: zynq: Switch to single zynq configurations There are a lot of zynq configurations which can be merged together and use only one for all. The similar change has been done for ZynqMP by commit be1b6c32d940 ("arm64: zynqmp: Use zynqmp_virt platform") Build SPL with u-boot.img for zc706 like this. export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8 u-boot.img is generic for all boards. Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-13 14:03:29 +00:00
CONFIG_MTD=y
CONFIG_MTD_NOR_FLASH=y
ARM: zynq: Enable DM for CFI NOR flash With multi defconfig NOR flash information about NOR should be taken from DT that's why there is no reason to specify address and sizes via fixed config. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-25 14:29:40 +00:00
CONFIG_CFI_FLASH=y
ARM: zynq: Switch to single zynq configurations There are a lot of zynq configurations which can be merged together and use only one for all. The similar change has been done for ZynqMP by commit be1b6c32d940 ("arm64: zynqmp: Use zynqmp_virt platform") Build SPL with u-boot.img for zc706 like this. export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8 u-boot.img is generic for all boards. Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-13 14:03:29 +00:00
CONFIG_SYS_FLASH_USE_BUFFER_WRITE=y
CONFIG_SYS_FLASH_CFI=y
Convert CONFIG_SYS_FLASH_QUIET_TEST to Kconfig This converts the following to Kconfig: CONFIG_SYS_FLASH_QUIET_TEST Signed-off-by: Tom Rini <trini@konsulko.com>
2022-07-23 17:05:05 +00:00
CONFIG_SYS_FLASH_QUIET_TEST=y
ARM: zynq: Switch to single zynq configurations There are a lot of zynq configurations which can be merged together and use only one for all. The similar change has been done for ZynqMP by commit be1b6c32d940 ("arm64: zynqmp: Use zynqmp_virt platform") Build SPL with u-boot.img for zc706 like this. export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8 u-boot.img is generic for all boards. Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-13 14:03:29 +00:00
CONFIG_MTD_RAW_NAND=y
CONFIG_NAND_ZYNQ=y
Convert CONFIG_SYS_NAND_ONFI_DETECTION to Kconfig This converts the following to Kconfig: CONFIG_SYS_NAND_ONFI_DETECTION Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-22 18:50:34 +00:00
CONFIG_SYS_NAND_ONFI_DETECTION=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_SF_DEFAULT_SPEED=30000000
CONFIG_SPI_FLASH_ISSI=y
CONFIG_SPI_FLASH_MACRONIX=y
CONFIG_SPI_FLASH_SPANSION=y
CONFIG_SPI_FLASH_STMICRO=y
ARM: zynq: Switch to single zynq configurations There are a lot of zynq configurations which can be merged together and use only one for all. The similar change has been done for ZynqMP by commit be1b6c32d940 ("arm64: zynqmp: Use zynqmp_virt platform") Build SPL with u-boot.img for zc706 like this. export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8 u-boot.img is generic for all boards. Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-13 14:03:29 +00:00
CONFIG_SPI_FLASH_SST=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_SPI_FLASH_WINBOND=y
CONFIG_PHY_MARVELL=y
ARM: zynq: Add Z-turn board V5 Adding Z-turn board V5 to resolve the change between: "Z-TURNBOARD_schematic.pdf" schematics state version 1 to 4 has Atheros AR8035 "Z-Turn_Board_sch_V15_20160303.pdf" schematics state version 5 has Micrel KSZ9031 At this time the S25FL128SAGNFI003 doesn't work because of bug: *** Warning - spi_flash_probe_bus_cs() failed, using default environment zynq-zturn was checked on V5 board, same error. Maybe Z-turn board have the same problem (board with W25Q128BVFIG). Signed-off-by: Alexandre GRIVEAUX <agriveaux@deutnet.info> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-10-01 08:33:36 +00:00
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ90X1=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_PHY_REALTEK=y
CONFIG_PHY_XILINX=y
xilinx: Add CONFIG_DM_ETH_PHY config Enable CONFIG_DM_ETH_PHY to utilize shared MDIO bus support on all xilinx platforms. Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com> Signed-off-by: Michal Simek <michal.simek@amd.com> Acked-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com> Link: https://lore.kernel.org/r/965981eb324d13a98aad8bd88eb8b50bc5147a7e.1652181968.git.michal.simek@amd.com
2022-05-10 11:26:11 +00:00
CONFIG_DM_ETH_PHY=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_MII=y
CONFIG_ZYNQ_GEM=y
serial: Convert ARM_DCC to Kconfig The symbol "CONFIG_ARM_DCC" is used to control building drivers/serial/arm_dcc.c. Provide a simple Kconfig entry for this. Cc: Luca Ceresoli <luca@lucaceresoli.net> Cc: Michal Simek <monstr@monstr.eu> Cc: Tom McLeod <tom.mcleod@opalkelly.com> Cc: Mike Looijmans <mike.looijmans@topic.nl> Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
2020-06-02 21:26:33 +00:00
CONFIG_ARM_DCC=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_ZYNQ_SERIAL=y
ARM: zynq: Switch to single zynq configurations There are a lot of zynq configurations which can be merged together and use only one for all. The similar change has been done for ZynqMP by commit be1b6c32d940 ("arm64: zynqmp: Use zynqmp_virt platform") Build SPL with u-boot.img for zc706 like this. export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8 u-boot.img is generic for all boards. Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-13 14:03:29 +00:00
CONFIG_ZYNQ_SPI=y
ARM: zynq: Introduce virtual defconfig Add virtual defconfig for Zynq architecture using of_board dtb. This defconfig should become generic config for all Zynq boards. Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-02 14:57:39 +00:00
CONFIG_ZYNQ_QSPI=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_ULPI_VIEWPORT=y
CONFIG_USB_ULPI=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_MANUFACTURER="Xilinx"
CONFIG_USB_GADGET_VENDOR_NUM=0x03fd
CONFIG_USB_GADGET_PRODUCT_NUM=0x0300
CONFIG_CI_UDC=y
CONFIG_USB_GADGET_DOWNLOAD=y
CONFIG_USB_FUNCTION_THOR=y
ARM: zynq: Switch to single zynq configurations There are a lot of zynq configurations which can be merged together and use only one for all. The similar change has been done for ZynqMP by commit be1b6c32d940 ("arm64: zynqmp: Use zynqmp_virt platform") Build SPL with u-boot.img for zc706 like this. export DEVICE_TREE=zynq-zc706 && make xilinx_zynq_virt_defconfig && make -j8 u-boot.img is generic for all boards. Tested on Zybo, zc702, zc706, zc770-xm011-x16, cc108 and microzed. Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-02-13 14:03:29 +00:00
CONFIG_DISPLAY=y
CONFIG_SPL_GZIP=y
ARM: zynq: Enable capsule update for qspi and mmc Generate dfu_alt_info setup at runtime for capsule update. Enabling this feature will help with upgrading boards without remembering what is where. The similar change was done for ZynqMP by commit b86f43de0be0 ("xilinx: zynqmp: Add support for runtime dfu_alt_info setup"). Code needs to be enabled by CONFIG_SET_DFU_ALT_INFO. And also enable capsule on disk for RAW firmware images with efidebug command. Two indexes are supported for SPL flow. Images can be generated like: ./tools/mkeficapsule --raw spl/boot.bin --index 1 capsule1.bin ./tools/mkeficapsule --raw u-boot.img --index 2 capsule2.bin Then place them to SD card and load them: load mmc 0 10000000 capsule1.bin && efidebug capsule update -v 10000000 load mmc 0 10000000 capsule2.bin && efidebug capsule update -v 10000000 FSBL flow will also work where only index 1 capsule is used. There should be enough space for using boot.bin with bitstream too. Zynq also support multiple boot locations in SPI or MMC but it is not wired by this patch. Signed-off-by: Michal Simek <michal.simek@xilinx.com> Link: https://lore.kernel.org/r/bea5fc75a87a5971f118b46bab4aa7ca39a629c6.1630061610.git.michal.simek@xilinx.com
2021-08-27 10:53:32 +00:00
CONFIG_EFI_RUNTIME_UPDATE_CAPSULE=y
CONFIG_EFI_CAPSULE_FIRMWARE_RAW=y
xilinx: zynq: Enable mkeficapsule tools compilation Zynq can use efi capsule infrastructure that's why enable it by default. For capsule generation for zynq you can use: pushd spl ../tools/mkeficapsule -g "1ba29a15-9969-40aa-b424-e86121618664" boot.bin \ --index 1 ../capsule1.bin popd ./tools/mkeficapsule -g "1a5178f0-87d3-4f36-ac63-3b31a23be305" u-boot.img \ --index 2 capsule2.bin Signed-off-by: Michal Simek <michal.simek@amd.com> Link: https://lore.kernel.org/r/a8194ecfa7932f2d8ada5ee508b2a026c782f15e.1660055571.git.michal.simek@amd.com
2022-08-09 14:32:51 +00:00
CONFIG_TOOLS_MKEFICAPSULE=y
Reference in a new issue Copy permalink