u-boot/board/novtech/meerkat96/imximage.cfg

127 lines
4.3 KiB
INI
Raw Normal View History

/*
* Copyright (C) 2014 Freescale Semiconductor, Inc.
*
* SPDX-License-Identifier: GPL-2.0+
*
* Refer docs/README.imxmage for more details about how-to configure
* and create imximage boot image
*
* The syntax is taken as close as possible with the kwbimage
*/
#include <config.h>
/* image version */
IMAGE_VERSION 2
/*
* Boot Device : sd
*/
BOOT_FROM sd
/*
* Secure boot support
*/
#ifdef CONFIG_IMX_HAB
CSF CONFIG_CSF_SIZE
#endif
/*
* Device Configuration Data (DCD)
*
* Each entry must have the format:
* Addr-type Address Value
*
* where:
* Addr-type register length (1,2 or 4 bytes)
* Address absolute address of the register
* value value to be stored in the register
*/
/* Enable OCRAM EPDC */
DATA 4 0x30340004 0x4F400005
/* =============================================================================
* DDR Controller Registers
* =============================================================================
* Memory type: DDR3
* Manufacturer: ISSI
* Device Part Number: IS43TR16256AL-125KBL
* Clock Freq.: 533MHz
* Density per CS in Gb: 4
* Chip Selects used: 1
* Number of Banks: 8
* Row address: 15
* Column address: 10
* Data bus width: 16
* ROW-BANK interleave: ENABLED
* =============================================================================
*/
DATA 4 0x30391000 0x00000002 // deassert presetn
DATA 4 0x307A0000 0x01041001 // DDRC_MSTR
DATA 4 0x307A0064 0x00400046 // DDRC_RFSHTMG
DATA 4 0x307a0490 0x00000001 // DDRC_PCTRL_0
DATA 4 0x307A00D4 0x00690000 // DDRC_INIT1
DATA 4 0x307A00D0 0x00020083 // DDRC_INIT0
DATA 4 0x307A00DC 0x09300004 // DDRC_INIT3
DATA 4 0x307A00E0 0x04080000 // DDRC_INIT4
DATA 4 0x307A00E4 0x00100004 // DDRC_INIT5
DATA 4 0x307A00F4 0x0000033F // DDRC_RANKCTL
DATA 4 0x307A0100 0x090B1109 // DDRC_DRAMTMG0
DATA 4 0x307A0104 0x0007020D // DDRC_DRAMTMG1
DATA 4 0x307A0108 0x03040407 // DDRC_DRAMTMG2
DATA 4 0x307A010C 0x00002006 // DDRC_DRAMTMG3
DATA 4 0x307A0110 0x04020205 // DDRC_DRAMTMG4
DATA 4 0x307A0114 0x03030202 // DDRC_DRAMTMG5
DATA 4 0x307A0120 0x00000803 // DDRC_DRAMTMG8
DATA 4 0x307A0180 0x00800020 // DDRC_ZQCTL0
DATA 4 0x307A0190 0x02098204 // DDRC_DFITMG0
DATA 4 0x307A0194 0x00030303 // DDRC_DFITMG1
DATA 4 0x307A01A0 0x80400003 // DDRC_DFIUPD0
DATA 4 0x307A01A4 0x00100020 // DDRC_DFIUPD1
DATA 4 0x307A01A8 0x80100004 // DDRC_DFIUPD2
DATA 4 0x307A0200 0x00000015 // DDRC_ADDRMAP0
DATA 4 0x307A0204 0x00070707 // DDRC_ADDRMAP1
DATA 4 0x307A0210 0x00000F0F // DDRC_ADDRMAP4
DATA 4 0x307A0214 0x06060606 // DDRC_ADDRMAP5
DATA 4 0x307A0218 0x0F060606 // DDRC_ADDRMAP6
DATA 4 0x307A0240 0x06000604 // DDRC_ODTCFG
DATA 4 0x307A0244 0x00000001 // DDRC_ODTMAP
/* =============================================================================
* PHY Control Register
* =============================================================================
*/
DATA 4 0x30391000 0x00000000 // deassert presetn
DATA 4 0x30790000 0x17420F40 // DDR_PHY_PHY_CON0
DATA 4 0x30790004 0x10210100 // DDR_PHY_PHY_CON1
DATA 4 0x30790010 0x00060807 // DDR_PHY_PHY_CON4
DATA 4 0x307900B0 0x1010007E // DDR_PHY_MDLL_CON0
DATA 4 0x3079009C 0x00000D6E // DDR_PHY_DRVDS_CON0
DATA 4 0x30790030 0x08080808 // DDR_PHY_OFFSET_WR_CON0
DATA 4 0x30790020 0x08080808 // DDR_PHY_OFFSET_RD_CON0
DATA 4 0x30790050 0x01000010 // DDR_PHY_OFFSETD_CON0
DATA 4 0x30790050 0x00000010 // DDR_PHY_OFFSETD_CON0
DATA 4 0x30790018 0x0000000F // DDR_PHY_LP_CON0
DATA 4 0x307900C0 0x0E407304 // DDR_PHY_ZQ_CON0 - Start Manual ZQ
DATA 4 0x307900C0 0x0E447304
DATA 4 0x307900C0 0x0E447306
DATA 4 0x307900C0 0x0E447304 // <= NOTE: Depending on JTAG device used, may need ~ 7 us pause at this point.
DATA 4 0x307900C0 0x0E407304 // DDR_PHY_ZQ_CON0 - End Manual ZQ
/* =============================================================================
* Final Initialization start sequence
* =============================================================================
*/
DATA 4 0x30384130 0x00000000 // Disable Clock
DATA 4 0x30340020 0x00000178 // IOMUX_GRP_GRP8 - Start input to PHY
DATA 4 0x30384130 0x00000002 // Enable Clock
/* <= NOTE: Depending on JTAG device used, may need ~ 250 us pause at this point. */