u-boot/board/freescale/imx8ulp_evk/ddr_init.c

208 lines
6.5 KiB
C
Raw Normal View History

arm: imx: add i.MX8ULP EVK support Add i.MX8ULP EVK basic support, support SD/I2C/ENET/LPUART Log as below: I would keep some debug info for now, and after we move to be stable and production launch, we could drop that. U-Boot SPL 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800) Normal Boot upower_init: soc_id=48 upower_init: version:11.11.6 upower_init: start uPower RAM service user_upwr_rdy_callb: soc=b user_upwr_rdy_callb: RAM version:12.6 Turn on switches ok Turn on memories ok Clear DDR retention ok Poll for freq_chg_req on SIM register and change to F1 frequency. Poll for freq_chg_req on SIM register and change to F0 frequency. Poll for freq_chg_req on SIM register and change to F1 frequency. Poll for freq_chg_req on SIM register and change to F2 frequency. Poll for freq_chg_req on SIM register and change to F1 frequency. Poll for freq_chg_req on SIM register and change to F2 frequency. complete De-Skew PLL is locked and ready WDT: Not found! Trying to boot from BOOTROM image offset 0x8000, pagesize 0x200, ivt offset 0x0 Load image from 0x3a800 by ROM_API NOTICE: BL31: v2.4(release):imx_5.10.35_2.0.0_imx8ulp_er-10-gf37e59b94 NOTICE: BL31: Built : 01:56:58, Jun 29 2021 NOTICE: upower_init: start uPower RAM service NOTICE: user_upwr_rdy_callb: soc=b NOTICE: user_upwr_rdy_callb: RAM version:12.6 U-Boot 2021.07-rc4-00164-gb800e19a6b (Jun 29 2021 - 10:23:30 +0800) CPU: Freescale i.MX8ULP rev1.0 at 744 MHz Reset cause: POR Boot mode: Single boot Model: FSL i.MX8ULP EVK DRAM: 2 GiB MMC: FSL_SDHC: 0, FSL_SDHC: 2 Loading Environment from MMC... *** Warning - bad CRC, using default environment In: serial@293a0000 Out: serial@293a0000 Err: serial@293a0000 Net: Warning: ethernet@29950000 (eth0) using random MAC address - 96:35:88:62:e0:44 eth0: ethernet@29950000 Hit any key to stop autoboot: 0 Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-08-07 08:01:13 +00:00
// SPDX-License-Identifier: GPL-2.0+ OR MIT
/*
* Copyright 2021 NXP
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/ddr.h>
#include <asm/arch/imx-regs.h>
#define DENALI_CTL_00 (DDR_CTL_BASE_ADDR)
#define CTL_START 0x1
#define DENALI_CTL_03 (DDR_CTL_BASE_ADDR + 4 * 3)
#define DENALI_CTL_197 (DDR_CTL_BASE_ADDR + 4 * 197)
#define DENALI_CTL_250 (DDR_CTL_BASE_ADDR + 4 * 250)
#define DENALI_CTL_251 (DDR_CTL_BASE_ADDR + 4 * 251)
#define DENALI_CTL_266 (DDR_CTL_BASE_ADDR + 4 * 266)
#define DFI_INIT_COMPLETE 0x2
#define DENALI_CTL_614 (DDR_CTL_BASE_ADDR + 4 * 614)
#define DENALI_CTL_615 (DDR_CTL_BASE_ADDR + 4 * 615)
#define DENALI_PI_00 (DDR_PI_BASE_ADDR)
#define PI_START 0x1
#define DENALI_PI_04 (DDR_PI_BASE_ADDR + 4 * 4)
#define DENALI_PI_11 (DDR_PI_BASE_ADDR + 4 * 11)
#define DENALI_PI_12 (DDR_PI_BASE_ADDR + 4 * 12)
#define DENALI_CTL_23 (DDR_CTL_BASE_ADDR + 4 * 23)
#define DENALI_CTL_25 (DDR_CTL_BASE_ADDR + 4 * 25)
#define DENALI_PHY_1624 (DDR_PHY_BASE_ADDR + 4 * 1624)
#define DENALI_PHY_1537 (DDR_PHY_BASE_ADDR + 4 * 1537)
#define PHY_FREQ_SEL_MULTICAST_EN(X) ((X) << 8)
#define PHY_FREQ_SEL_INDEX(X) ((X) << 16)
#define DENALI_PHY_1547 (DDR_PHY_BASE_ADDR + 4 * 1547)
#define DENALI_PHY_1555 (DDR_PHY_BASE_ADDR + 4 * 1555)
#define DENALI_PHY_1564 (DDR_PHY_BASE_ADDR + 4 * 1564)
#define DENALI_PHY_1565 (DDR_PHY_BASE_ADDR + 4 * 1565)
int ddr_calibration(unsigned int fsp_table[3])
{
u32 reg_val;
u32 int_status_init, phy_freq_req, phy_freq_type;
u32 lock_0, lock_1, lock_2;
u32 freq_chg_pt, freq_chg_cnt;
reg_val = readl(DENALI_CTL_250);
if (((reg_val >> 16) & 0x3) == 1)
freq_chg_cnt = 2;
else
freq_chg_cnt = 3;
reg_val = readl(DENALI_PI_12);
if (reg_val == 0x3) {
freq_chg_pt = 1;
} else if (reg_val == 0x7) {
freq_chg_pt = 2;
} else {
printf("frequency map(0x%x) is wrong, please check!\r\n", reg_val);
return -1;
}
debug("%s\n", __func__);
/* Assert PI_START parameter and then assert START parameter in Controller. */
reg_val = readl(DENALI_PI_00) | PI_START;
writel(reg_val, DENALI_PI_00);
reg_val = readl(DENALI_CTL_00) | CTL_START;
writel(reg_val, DENALI_CTL_00);
/* Poll for init_done_bit in Controller interrupt status register (INT_STATUS_INIT) */
do {
if (!freq_chg_cnt) {
int_status_init = (readl(DENALI_CTL_266) >> 8) & 0xff;
/* DDR subsystem is ready for traffic. */
if (int_status_init & DFI_INIT_COMPLETE) {
printf("complete\n");
break;
}
}
/*
* During leveling, PHY will request for freq change and SoC clock
* logic should provide requested frequency, Polling SIM LPDDR_CTRL2
* Bit phy_freq_chg_req until be 1'b1
*/
reg_val = readl(AVD_SIM_LPDDR_CTRL2);
phy_freq_req = (reg_val >> 7) & 0x1;
if (phy_freq_req) {
phy_freq_type = reg_val & 0x1F;
if (!phy_freq_type) {
printf("Poll for freq_chg_req on SIM register and change to F0 frequency.\n");
set_ddr_clk(fsp_table[phy_freq_type] >> 1);
/* Write 1'b1 at LPDDR_CTRL2 bit phy_freq_cfg_ack */
reg_val = readl(AVD_SIM_LPDDR_CTRL2);
writel(reg_val | (0x1 << 6), AVD_SIM_LPDDR_CTRL2);
} else if (phy_freq_type == 0x01) {
printf("Poll for freq_chg_req on SIM register and change to F1 frequency.\n");
set_ddr_clk(fsp_table[phy_freq_type] >> 1);
/* Write 1'b1 at LPDDR_CTRL2 bit phy_freq_cfg_ack */
reg_val = readl(AVD_SIM_LPDDR_CTRL2);
writel(reg_val | (0x1 << 6), AVD_SIM_LPDDR_CTRL2);
if (freq_chg_pt == 1)
freq_chg_cnt--;
} else if (phy_freq_type == 0x02) {
printf("Poll for freq_chg_req on SIM register and change to F2 frequency.\n");
set_ddr_clk(fsp_table[phy_freq_type] >> 1);
/* Write 1'b1 at LPDDR_CTRL2 bit phy_freq_cfg_ack */
reg_val = readl(AVD_SIM_LPDDR_CTRL2);
writel(reg_val | (0x1 << 6), AVD_SIM_LPDDR_CTRL2);
if (freq_chg_pt == 2)
freq_chg_cnt--;
}
reg_val = readl(AVD_SIM_LPDDR_CTRL2);
}
} while (1);
/* Check PLL lock status */
lock_0 = readl(DENALI_PHY_1564) & 0xffff;
lock_1 = (readl(DENALI_PHY_1564) >> 16) & 0xffff;
lock_2 = readl(DENALI_PHY_1565) & 0xffff;
if ((lock_0 & 0x3) != 0x3 || (lock_1 & 0x3) != 0x3 || (lock_2 & 0x3) != 0x3) {
printf("De-Skew PLL failed to lock\n");
printf("lock_0=0x%x, lock_1=0x%x, lock_2=0x%x\n", lock_0, lock_1, lock_2);
return -1;
}
printf("De-Skew PLL is locked and ready\n");
return 0;
}
int ddr_init(struct dram_timing_info2 *dram_timing)
{
int i;
debug("%s\n", __func__);
set_ddr_clk(dram_timing->fsp_table[0] >> 1); /* Set to boot freq */
/* Initialize CTL registers */
for (i = 0; i < dram_timing->ctl_cfg_num; i++)
writel(dram_timing->ctl_cfg[i].val, (ulong)dram_timing->ctl_cfg[i].reg);
/* Initialize PI registers */
for (i = 0; i < dram_timing->pi_cfg_num; i++)
writel(dram_timing->pi_cfg[i].val, (ulong)dram_timing->pi_cfg[i].reg);
/* Write PHY regiters for all 3 frequency points (48Mhz/384Mhz/528Mhz): f1_index=0 */
writel(PHY_FREQ_SEL_MULTICAST_EN(1) | PHY_FREQ_SEL_INDEX(0), DENALI_PHY_1537);
for (i = 0; i < dram_timing->phy_f1_cfg_num; i++)
writel(dram_timing->phy_f1_cfg[i].val, (ulong)dram_timing->phy_f1_cfg[i].reg);
/* Write PHY regiters for freqency point 2 (528Mhz): f2_index=1 */
writel(PHY_FREQ_SEL_MULTICAST_EN(0) | PHY_FREQ_SEL_INDEX(1), DENALI_PHY_1537);
for (i = 0; i < dram_timing->phy_f2_cfg_num; i++)
writel(dram_timing->phy_f2_cfg[i].val, (ulong)dram_timing->phy_f2_cfg[i].reg);
/* Re-enable MULTICAST mode */
writel(PHY_FREQ_SEL_MULTICAST_EN(1) | PHY_FREQ_SEL_INDEX(0), DENALI_PHY_1537);
return ddr_calibration(dram_timing->fsp_table);
}
void enable_bypass_mode(void)
{
u32 reg_val;
/* PI_INIT_LVL_EN=0x0 (DENALI_PI_04) */
reg_val = readl(DENALI_PI_04) & ~0x1;
writel(reg_val, DENALI_PI_04);
/* PI_FREQ_MAP=0x1 (DENALI_PI_12) */
writel(0x1, DENALI_PI_12);
/* PI_INIT_WORK_FREQ=0x0 (DENALI_PI_11) */
reg_val = readl(DENALI_PI_11) & ~(0x1f << 8);
writel(reg_val, DENALI_PI_11);
/* DFIBUS_FREQ_INIT=0x0 (DENALI_CTL_23) */
reg_val = readl(DENALI_CTL_23) & ~(0x3 << 24);
writel(reg_val, DENALI_CTL_23);
/* PHY_LP4_BOOT_DISABLE=0x0 (DENALI_PHY_1547) */
reg_val = readl(DENALI_PHY_1547) & ~(0x1 << 8);
writel(reg_val, DENALI_PHY_1547);
/* PHY_PLL_BYPASS=0x1 (DENALI_PHY_1624) */
reg_val = readl(DENALI_PHY_1624) | 0x1;
writel(reg_val, DENALI_PHY_1624);
/* PHY_LP4_BOOT_PLL_BYPASS to 0x1 (DENALI_PHY_1555) */
reg_val = readl(DENALI_PHY_1555) | 0x1;
writel(reg_val, DENALI_PHY_1555);
/* FREQ_CHANGE_TYPE_F0 = 0x0/FREQ_CHANGE_TYPE_F1 = 0x1/FREQ_CHANGE_TYPE_F2 = 0x2 */
reg_val = 0x020100;
writel(reg_val, DENALI_CTL_25);
}