u-boot/include/configs/omap3_overo.h

225 lines
6.8 KiB
C
Raw Normal View History

/*
* Configuration settings for the Gumstix Overo board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#define CONFIG_NAND
#include <configs/ti_omap3_common.h>
/* Display CPU and Board information */
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
/* call misc_init_r */
#define CONFIG_MISC_INIT_R
/* pass the revision tag */
#define CONFIG_REVISION_TAG
/* override size of malloc() pool */
#undef CONFIG_SYS_MALLOC_LEN
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB sector */
/* Shift 128 << 15 provides 4 MiB heap to support UBI commands.
* Shift 128 << 10 provides 128 KiB heap for limited-memory devices. */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + (128 << 15))
/* I2C Support */
#define CONFIG_SYS_I2C_OMAP34XX
/* TWL4030 LED */
#define CONFIG_TWL4030_LED
/* Initialize GPIOs by default */
#define CONFIG_OMAP3_GPIO_2 /* GPIO32..63 is in GPIO Bank 2 */
#define CONFIG_OMAP3_GPIO_3 /* GPIO64..95 is in GPIO Bank 3 */
#define CONFIG_OMAP3_GPIO_4 /* GPIO96..127 is in GPIO Bank 4 */
#define CONFIG_OMAP3_GPIO_5 /* GPIO128..159 is in GPIO Bank 5 */
#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO Bank 6 */
/* commands to include */
#define CONFIG_CMD_CACHE
#undef CONFIG_CMD_FPGA /* FPGA configuration Support */
#undef CONFIG_CMD_IMI /* iminfo */
#undef CONFIG_CMD_NFS /* NFS support */
#ifdef CONFIG_NAND
#define CONFIG_CMD_UBI /* UBI-formated MTD partition support */
#define CONFIG_CMD_UBIFS /* Read-only UBI volume operations */
#define CONFIG_RBTREE /* required by CONFIG_CMD_UBI */
#define CONFIG_LZO /* required by CONFIG_CMD_UBIFS */
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
/* NAND block size is 128 KiB. Synchronize these values with
* overo_nand_partitions in mach-omap2/board-overo.c in Linux:
* xloader 4 * NAND_BLOCK_SIZE = 512 KiB
* uboot 14 * NAND_BLOCK_SIZE = 1792 KiB
* uboot environtment 2 * NAND_BLOCK_SIZE = 256 KiB
* linux 64 * NAND_BLOCK_SIZE = 8 MiB
* rootfs remainder
*/
#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:" \
"512k(xloader)," \
"1792k(u-boot)," \
"256k(environ)," \
"8m(linux)," \
"-(rootfs)"
#else /* CONFIG_NAND */
#define MTDPARTS_DEFAULT
#endif /* CONFIG_NAND */
/* Board NAND Info. */
#define CONFIG_SYS_NAND_QUIET_TEST
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
/* Environment information */
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
"bootdir=/boot\0" \
"bootfile=zImage\0" \
"usbtty=cdc_acm\0" \
"console=ttyO2,115200n8\0" \
"mpurate=auto\0" \
"optargs=\0" \
"vram=12M\0" \
"dvimode=1024x768MR-16@60\0" \
"defaultdisplay=dvi\0" \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext3 rootwait\0" \
"nandroot=ubi0:rootfs ubi.mtd=4\0" \
"nandrootfstype=ubifs\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
"mmcargs=setenv bootargs console=${console} " \
"${optargs} " \
"mpurate=${mpurate} " \
"vram=${vram} " \
"omapfb.mode=dvi:${dvimode} " \
"omapdss.def_disp=${defaultdisplay} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype}\0" \
"nandargs=setenv bootargs console=${console} " \
"${optargs} " \
"mpurate=${mpurate} " \
"vram=${vram} " \
"omapfb.mode=dvi:${dvimode} " \
"omapdss.def_disp=${defaultdisplay} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
"loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo Running boot script from mmc ...; " \
"source ${loadaddr}\0" \
"loadbootenv=load mmc ${mmcdev} ${loadaddr} uEnv.txt\0" \
"importbootenv=echo Importing environment from mmc ...; " \
"env import -t ${loadaddr} ${filesize}\0" \
"loaduimage=load mmc ${mmcdev} ${loadaddr} uImage\0" \
"mmcboot=echo Booting from mmc...; " \
"run mmcargs; " \
"bootm ${loadaddr}\0" \
"loadzimage=load mmc ${mmcdev}:2 ${loadaddr} ${bootdir}/${bootfile}\0" \
"loadfdt=load mmc ${mmcdev}:2 ${fdtaddr} ${bootdir}/${fdtfile}\0" \
"mmcbootfdt=echo Booting with DT from mmc ...; " \
"run mmcargs; " \
"bootz ${loadaddr} - ${fdtaddr}\0" \
"nandboot=echo Booting from nand ...; " \
"run nandargs; " \
"nand read ${loadaddr} linux; " \
"bootm ${loadaddr}\0" \
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"fi;" \
"if run loadbootenv; then " \
"echo Loaded environment from ${bootenv};" \
"run importbootenv;" \
"fi;" \
"if test -n $uenvcmd; then " \
"echo Running uenvcmd ...;" \
"run uenvcmd;" \
"fi;" \
"if run loaduimage; then " \
"run mmcboot;" \
"fi;" \
"if run loadzimage; then " \
"if test $fdtfile; then " \
"setenv fdtfile omap3-${boardname}-${expansionname}.dtb;" \
"fi;" \
"if run loadfdt; then " \
"run mmcbootfdt;" \
"fi;" \
"fi;" \
"fi;" \
"run nandboot; " \
/*
* Miscellaneous configurable options
*/
#undef CONFIG_SYS_PROMPT
#define CONFIG_SYS_PROMPT "Overo # "
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
/* FLASH and environment organization */
/* Configure the PISMO */
#define PISMO1_NAND_SIZE GPMC_SIZE_128M
#define PISMO1_ONEN_SIZE GPMC_SIZE_128M
#if defined(CONFIG_NAND)
#define CONFIG_SYS_FLASH_BASE PISMO1_NAND_BASE
#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_ONENAND_BASE ONENAND_MAP
#define CONFIG_ENV_IS_IN_NAND
#define ONENAND_ENV_OFFSET 0x240000 /* environment starts here */
#define SMNAND_ENV_OFFSET 0x240000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
/* Configure SMSC9211 ethernet */
#if defined(CONFIG_CMD_NET)
#define CONFIG_SMC911X
#define CONFIG_SMC911X_32_BIT
#define CONFIG_SMC911X_BASE 0x2C000000
#endif /* (CONFIG_CMD_NET) */
/* Initial RAM setup */
#define CONFIG_SYS_INIT_RAM_ADDR 0x4020f800
#define CONFIG_SYS_INIT_RAM_SIZE 0x800
#define CONFIG_SYS_CACHELINE_SIZE 64
/* NAND boot config */
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT 16
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE (128*1024)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9,\
10, 11, 12, 13}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 3
mtd: nand: omap: add CONFIG_NAND_OMAP_ECCSCHEME for selection of ecc-scheme This patch adds new CONFIG_NAND_OMAP_ECCSCHEME, replacing other distributed CONFIG_xx used for selecting NAND ecc-schemes. This patch aims at solving following issues. 1) Currently ecc-scheme is tied to SoC platform, which prevents user to select other ecc-schemes also supported in hardware. like; - most of OMAP3 SoC platforms use only 1-bit Hamming ecc-scheme, inspite the fact that they can use higher ecc-schemes like 8-bit ecc-schemes with software based error detection (OMAP_ECC_BCH4_CODE_HW_DETECTION_SW). - most of AM33xx SoC plaforms use 8-bit BCH ecc-scheme for now, but hardware supports BCH16 ecc-scheme also. 2) Different platforms use different CONFIG_xx to select ecc-schemes, which adds confusion for user while migrating platforms. - *CONFIG_NAND_OMAP_ELM* which enables ELM hardware engine, selects only 8-bit BCH ecc-scheme with h/w based error-correction (OMAP_ECC_BCH8_CODE_HW) whereas ELM hardware engine supports other ecc-schemes also like; BCH4, and BCH16 (in future). - *CONFIG_NAND_OMAP_BCH8* selects 8-bit BCH ecc-scheme with s/w based error correction (OMAP_ECC_BCH8_CODE_HW_DETECTION_SW). - *CONFIG_SPL_NAND_SOFTECC* selects 1-bit Hamming ecc-scheme using s/w library Thus adding new *CONFIG_NAND_OMAP_ECCSCHEME* de-couples ecc-scheme dependency on SoC platform and NAND driver. And user can select ecc-scheme independently foreach board. However, selection some hardware based ecc-schemes (OMAP_ECC_BCHx_CODE_HW) still depends on presence of ELM hardware engine on SoC. (Refer doc/README.nand) Signed-off-by: Pekon Gupta <pekon@ti.com>
2013-11-18 13:33:01 +00:00
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_HAM1_CODE_HW
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#endif /* __CONFIG_H */