u-boot/arch/arm/mach-sunxi/spl_spi_sunxi.c

375 lines
11 KiB
C
Raw Normal View History

// SPDX-License-Identifier: GPL-2.0+
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/*
* Copyright (C) 2016 Siarhei Siamashka <siarhei.siamashka@gmail.com>
*/
#include <common.h>
#include <image.h>
#include <log.h>
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
#include <spl.h>
#include <asm/arch/spl.h>
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
#include <asm/gpio.h>
#include <asm/io.h>
#include <linux/bitops.h>
#include <linux/delay.h>
#include <linux/libfdt.h>
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
#ifdef CONFIG_SPL_OS_BOOT
#error CONFIG_SPL_OS_BOOT is not supported yet
#endif
/*
* This is a very simple U-Boot image loading implementation, trying to
* replicate what the boot ROM is doing when loading the SPL. Because we
* know the exact pins where the SPI Flash is connected and also know
* that the Read Data Bytes (03h) command is supported, the hardware
* configuration is very simple and we don't need the extra flexibility
* of the SPI framework. Moreover, we rely on the default settings of
* the SPI controler hardware registers and only adjust what needs to
* be changed. This is good for the code size and this implementation
* adds less than 400 bytes to the SPL.
*
* There are two variants of the SPI controller in Allwinner SoCs:
* A10/A13/A20 (sun4i variant) and everything else (sun6i variant).
* Both of them are supported.
*
* The pin mixing part is SoC specific and only A10/A13/A20/H3/A64 are
* supported at the moment.
*/
/*****************************************************************************/
/* SUN4I variant of the SPI controller */
/*****************************************************************************/
#define SUN4I_SPI0_CCTL 0x1C
#define SUN4I_SPI0_CTL 0x08
#define SUN4I_SPI0_RX 0x00
#define SUN4I_SPI0_TX 0x04
#define SUN4I_SPI0_FIFO_STA 0x28
#define SUN4I_SPI0_BC 0x20
#define SUN4I_SPI0_TC 0x24
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
#define SUN4I_CTL_ENABLE BIT(0)
#define SUN4I_CTL_MASTER BIT(1)
#define SUN4I_CTL_TF_RST BIT(8)
#define SUN4I_CTL_RF_RST BIT(9)
#define SUN4I_CTL_XCH BIT(10)
/*****************************************************************************/
/* SUN6I variant of the SPI controller */
/*****************************************************************************/
#define SUN6I_SPI0_CCTL 0x24
#define SUN6I_SPI0_GCR 0x04
#define SUN6I_SPI0_TCR 0x08
#define SUN6I_SPI0_FIFO_STA 0x1C
#define SUN6I_SPI0_MBC 0x30
#define SUN6I_SPI0_MTC 0x34
#define SUN6I_SPI0_BCC 0x38
#define SUN6I_SPI0_TXD 0x200
#define SUN6I_SPI0_RXD 0x300
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
#define SUN6I_CTL_ENABLE BIT(0)
#define SUN6I_CTL_MASTER BIT(1)
#define SUN6I_CTL_SRST BIT(31)
#define SUN6I_TCR_XCH BIT(31)
/*****************************************************************************/
#define CCM_AHB_GATING0 (0x01C20000 + 0x60)
#define CCM_H6_SPI_BGR_REG (0x03001000 + 0x96c)
#ifdef CONFIG_MACH_SUN50I_H6
#define CCM_SPI0_CLK (0x03001000 + 0x940)
#else
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
#define CCM_SPI0_CLK (0x01C20000 + 0xA0)
#endif
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
#define SUN6I_BUS_SOFT_RST_REG0 (0x01C20000 + 0x2C0)
#define AHB_RESET_SPI0_SHIFT 20
#define AHB_GATE_OFFSET_SPI0 20
#define SPI0_CLK_DIV_BY_2 0x1000
#define SPI0_CLK_DIV_BY_4 0x1001
#define SPI0_CLK_DIV_BY_32 0x100f
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/*****************************************************************************/
/*
* Allwinner A10/A20 SoCs were using pins PC0,PC1,PC2,PC23 for booting
* from SPI Flash, everything else is using pins PC0,PC1,PC2,PC3.
* The H6 uses PC0, PC2, PC3, PC5.
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
*/
static void spi0_pinmux_setup(unsigned int pin_function)
{
/* All chips use PC0 and PC2. */
sunxi_gpio_set_cfgpin(SUNXI_GPC(0), pin_function);
sunxi_gpio_set_cfgpin(SUNXI_GPC(2), pin_function);
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/* All chips except H6 use PC1, and only H6 uses PC5. */
if (!IS_ENABLED(CONFIG_MACH_SUN50I_H6))
sunxi_gpio_set_cfgpin(SUNXI_GPC(1), pin_function);
else
sunxi_gpio_set_cfgpin(SUNXI_GPC(5), pin_function);
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/* Older generations use PC23 for CS, newer ones use PC3. */
if (IS_ENABLED(CONFIG_MACH_SUN4I) || IS_ENABLED(CONFIG_MACH_SUN7I) ||
IS_ENABLED(CONFIG_MACH_SUN8I_R40))
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
sunxi_gpio_set_cfgpin(SUNXI_GPC(23), pin_function);
else
sunxi_gpio_set_cfgpin(SUNXI_GPC(3), pin_function);
}
static bool is_sun6i_gen_spi(void)
{
return IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I) ||
IS_ENABLED(CONFIG_MACH_SUN50I_H6);
}
static uintptr_t spi0_base_address(void)
{
if (IS_ENABLED(CONFIG_MACH_SUN8I_R40))
return 0x01C05000;
if (IS_ENABLED(CONFIG_MACH_SUN50I_H6))
return 0x05010000;
if (!is_sun6i_gen_spi() ||
IS_ENABLED(CONFIG_MACH_SUNIV))
return 0x01C05000;
return 0x01C68000;
}
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/*
* Setup 6 MHz from OSC24M (because the BROM is doing the same).
*/
static void spi0_enable_clock(void)
{
uintptr_t base = spi0_base_address();
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/* Deassert SPI0 reset on SUN6I */
if (IS_ENABLED(CONFIG_MACH_SUN50I_H6))
setbits_le32(CCM_H6_SPI_BGR_REG, (1U << 16) | 0x1);
else if (is_sun6i_gen_spi())
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
setbits_le32(SUN6I_BUS_SOFT_RST_REG0,
(1 << AHB_RESET_SPI0_SHIFT));
/* Open the SPI0 gate */
if (!IS_ENABLED(CONFIG_MACH_SUN50I_H6))
setbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0));
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
if (IS_ENABLED(CONFIG_MACH_SUNIV)) {
/* Divide by 32, clock source is AHB clock 200MHz */
writel(SPI0_CLK_DIV_BY_32, base + SUN6I_SPI0_CCTL);
} else {
/* Divide by 4 */
writel(SPI0_CLK_DIV_BY_4, base + (is_sun6i_gen_spi() ?
SUN6I_SPI0_CCTL : SUN4I_SPI0_CCTL));
/* 24MHz from OSC24M */
writel((1 << 31), CCM_SPI0_CLK);
}
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
if (is_sun6i_gen_spi()) {
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/* Enable SPI in the master mode and do a soft reset */
setbits_le32(base + SUN6I_SPI0_GCR, SUN6I_CTL_MASTER |
SUN6I_CTL_ENABLE | SUN6I_CTL_SRST);
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/* Wait for completion */
while (readl(base + SUN6I_SPI0_GCR) & SUN6I_CTL_SRST)
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
;
} else {
/* Enable SPI in the master mode and reset FIFO */
setbits_le32(base + SUN4I_SPI0_CTL, SUN4I_CTL_MASTER |
SUN4I_CTL_ENABLE |
SUN4I_CTL_TF_RST |
SUN4I_CTL_RF_RST);
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
}
}
static void spi0_disable_clock(void)
{
uintptr_t base = spi0_base_address();
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/* Disable the SPI0 controller */
if (is_sun6i_gen_spi())
clrbits_le32(base + SUN6I_SPI0_GCR, SUN6I_CTL_MASTER |
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
SUN6I_CTL_ENABLE);
else
clrbits_le32(base + SUN4I_SPI0_CTL, SUN4I_CTL_MASTER |
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
SUN4I_CTL_ENABLE);
/* Disable the SPI0 clock */
if (!IS_ENABLED(CONFIG_MACH_SUNIV))
writel(0, CCM_SPI0_CLK);
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/* Close the SPI0 gate */
if (!IS_ENABLED(CONFIG_MACH_SUN50I_H6))
clrbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0));
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/* Assert SPI0 reset on SUN6I */
if (IS_ENABLED(CONFIG_MACH_SUN50I_H6))
clrbits_le32(CCM_H6_SPI_BGR_REG, (1U << 16) | 0x1);
else if (is_sun6i_gen_spi())
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
clrbits_le32(SUN6I_BUS_SOFT_RST_REG0,
(1 << AHB_RESET_SPI0_SHIFT));
}
static void spi0_init(void)
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
{
unsigned int pin_function = SUNXI_GPC_SPI0;
if (IS_ENABLED(CONFIG_MACH_SUN50I) ||
IS_ENABLED(CONFIG_MACH_SUN50I_H6))
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
pin_function = SUN50I_GPC_SPI0;
else if (IS_ENABLED(CONFIG_MACH_SUNIV))
pin_function = SUNIV_GPC_SPI0;
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
spi0_pinmux_setup(pin_function);
spi0_enable_clock();
}
static void spi0_deinit(void)
{
/* New SoCs can disable pins, older could only set them as input */
unsigned int pin_function = SUNXI_GPIO_INPUT;
if (is_sun6i_gen_spi())
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
pin_function = SUNXI_GPIO_DISABLE;
spi0_disable_clock();
spi0_pinmux_setup(pin_function);
}
/*****************************************************************************/
#define SPI_READ_MAX_SIZE 60 /* FIFO size, minus 4 bytes of the header */
static void sunxi_spi0_read_data(u8 *buf, u32 addr, u32 bufsize,
ulong spi_ctl_reg,
ulong spi_ctl_xch_bitmask,
ulong spi_fifo_reg,
ulong spi_tx_reg,
ulong spi_rx_reg,
ulong spi_bc_reg,
ulong spi_tc_reg,
ulong spi_bcc_reg)
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
{
writel(4 + bufsize, spi_bc_reg); /* Burst counter (total bytes) */
writel(4, spi_tc_reg); /* Transfer counter (bytes to send) */
if (spi_bcc_reg)
writel(4, spi_bcc_reg); /* SUN6I also needs this */
/* Send the Read Data Bytes (03h) command header */
writeb(0x03, spi_tx_reg);
writeb((u8)(addr >> 16), spi_tx_reg);
writeb((u8)(addr >> 8), spi_tx_reg);
writeb((u8)(addr), spi_tx_reg);
/* Start the data transfer */
setbits_le32(spi_ctl_reg, spi_ctl_xch_bitmask);
/* Wait until everything is received in the RX FIFO */
while ((readl(spi_fifo_reg) & 0x7F) < 4 + bufsize)
;
/* Skip 4 bytes */
readl(spi_rx_reg);
/* Read the data */
while (bufsize-- > 0)
*buf++ = readb(spi_rx_reg);
/* tSHSL time is up to 100 ns in various SPI flash datasheets */
udelay(1);
}
static void spi0_read_data(void *buf, u32 addr, u32 len)
{
u8 *buf8 = buf;
u32 chunk_len;
uintptr_t base = spi0_base_address();
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
while (len > 0) {
chunk_len = len;
if (chunk_len > SPI_READ_MAX_SIZE)
chunk_len = SPI_READ_MAX_SIZE;
if (is_sun6i_gen_spi()) {
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
sunxi_spi0_read_data(buf8, addr, chunk_len,
base + SUN6I_SPI0_TCR,
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
SUN6I_TCR_XCH,
base + SUN6I_SPI0_FIFO_STA,
base + SUN6I_SPI0_TXD,
base + SUN6I_SPI0_RXD,
base + SUN6I_SPI0_MBC,
base + SUN6I_SPI0_MTC,
base + SUN6I_SPI0_BCC);
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
} else {
sunxi_spi0_read_data(buf8, addr, chunk_len,
base + SUN4I_SPI0_CTL,
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
SUN4I_CTL_XCH,
base + SUN4I_SPI0_FIFO_STA,
base + SUN4I_SPI0_TX,
base + SUN4I_SPI0_RX,
base + SUN4I_SPI0_BC,
base + SUN4I_SPI0_TC,
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
0);
}
len -= chunk_len;
buf8 += chunk_len;
addr += chunk_len;
}
}
static ulong spi_load_read(struct spl_load_info *load, ulong sector,
ulong count, void *buf)
{
spi0_read_data(buf, sector, count);
return count;
}
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
/*****************************************************************************/
static int spl_spi_load_image(struct spl_image_info *spl_image,
struct spl_boot_device *bootdev)
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
{
int ret = 0;
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
struct image_header *header;
header = (struct image_header *)(CONFIG_SYS_TEXT_BASE);
uint32_t load_offset = sunxi_get_spl_size();
load_offset = max_t(uint32_t, load_offset, CONFIG_SYS_SPI_U_BOOT_OFFS);
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
spi0_init();
spi0_read_data((void *)header, load_offset, 0x40);
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
if (IS_ENABLED(CONFIG_SPL_LOAD_FIT) &&
image_get_magic(header) == FDT_MAGIC) {
struct spl_load_info load;
debug("Found FIT image\n");
load.dev = NULL;
load.priv = NULL;
load.filename = NULL;
load.bl_len = 1;
load.read = spi_load_read;
ret = spl_load_simple_fit(spl_image, &load,
load_offset, header);
} else {
ret = spl_parse_image_header(spl_image, bootdev, header);
if (ret)
return ret;
spi0_read_data((void *)spl_image->load_addr,
load_offset, spl_image->size);
}
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
spi0_deinit();
return ret;
sunxi: Support booting from SPI flash Allwinner devices support SPI flash as one of the possible bootable media type. The SPI flash chip needs to be connected to SPI0 pins (port C) to make this work. More information is available at: https://linux-sunxi.org/Bootable_SPI_flash This patch adds the initial support for booting from SPI flash. The existing SPI frameworks are not used in order to reduce the SPL code size. Right now the SPL size grows by ~370 bytes when CONFIG_SPL_SPI_SUNXI option is enabled. While there are no popular Allwinner devices with SPI flash at the moment, testing can be done using a SPI flash module (it can be bought for ~2$ on ebay) and jumper wires with the boards, which expose relevant pins on the expansion header. The SPI flash chips themselves are very cheap (some prices are even listed as low as 4 cents) and should not cost much if somebody decides to design a development board with an SPI flash chip soldered on the PCB. Another nice feature of the SPI flash is that it can be safely accessed in a device-independent way (since we know that the boot ROM is already probing these pins during the boot time). And if, for example, Olimex boards opted to use SPI flash instead of EEPROM, then they would have been able to have U-Boot installed in the SPI flash now and boot the rest of the system from the SATA hard drive. Hopefully we may see new interesting Allwinner based development boards in the future, now that the software support for the SPI flash is in a better shape :-) Testing can be done by enabling the CONFIG_SPL_SPI_SUNXI option in a board defconfig, then building U-Boot and finally flashing the resulting u-boot-sunxi-with-spl.bin binary over USB OTG with a help of the sunxi-fel tool: sunxi-fel spiflash-write 0 u-boot-sunxi-with-spl.bin The device needs to be switched into FEL (USB recovery) mode first. The most suitable boards for testing are Orange Pi PC and Pine64. Because these boards are cheap, have no built-in NAND/eMMC and expose SPI0 pins on the Raspberry Pi compatible expansion header. The A13-OLinuXino-Micro board also can be used. Signed-off-by: Siarhei Siamashka <siarhei.siamashka@gmail.com> Reviewed-by: Simon Glass <sjg@chromium.org> Signed-off-by: Hans de Goede <hdegoede@redhat.com>
2016-06-07 11:28:34 +00:00
}
/* Use priorty 0 to override the default if it happens to be linked in */
SPL_LOAD_IMAGE_METHOD("sunxi SPI", 0, BOOT_DEVICE_SPI, spl_spi_load_image);