u-boot/include/configs/ls1088a_common.h

185 lines
5.5 KiB
C
Raw Normal View History

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2017-2018 NXP
*/
#ifndef __LS1088_COMMON_H
#define __LS1088_COMMON_H
/* SPL build */
#ifdef CONFIG_SPL_BUILD
#define SPL_NO_BOARDINFO
#define SPL_NO_QIXIS
#define SPL_NO_PCI
#define SPL_NO_ENV
#define SPL_NO_RTC
#define SPL_NO_USB
#define SPL_NO_SATA
#define SPL_NO_QSPI
#define SPL_NO_IFC
#endif
#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
#include <asm/arch/soc.h>
#define LS1088ARDB_PB_BOARD 0x4A
/* Link Definitions */
#ifdef CONFIG_TFABOOT
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
#else
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_FSL_OCRAM_BASE + 0xfff0)
#endif
/* Link Definitions */
#define CONFIG_SYS_FSL_QSPI_BASE 0x20000000
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x8080000000ULL
#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 1
/*
* SMP Definitinos
*/
#define CPU_RELEASE_ADDR secondary_boot_addr
/* GPIO */
/* I2C */
/* Serial Port */
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK (get_bus_freq(0) / 2)
/*
* During booting, IFC is mapped at the region of 0x30000000.
* But this region is limited to 256MB. To accommodate NOR, promjet
* and FPGA. This region is divided as below:
* 0x30000000 - 0x37ffffff : 128MB : NOR flash
* 0x38000000 - 0x3BFFFFFF : 64MB : Promjet
* 0x3C000000 - 0x40000000 : 64MB : FPGA etc
*
* To accommodate bigger NOR flash and other devices, we will map IFC
* chip selects to as below:
* 0x5_1000_0000..0x5_1fff_ffff Memory Hole
* 0x5_2000_0000..0x5_3fff_ffff IFC CSx (FPGA, NAND and others 512MB)
* 0x5_4000_0000..0x5_7fff_ffff ASIC or others 1GB
* 0x5_8000_0000..0x5_bfff_ffff IFC CS0 1GB (NOR/Promjet)
* 0x5_C000_0000..0x5_ffff_ffff IFC CS1 1GB (NOR/Promjet)
*
* For e.g. NOR flash at CS0 will be mapped to 0x580000000 after relocation.
* CONFIG_SYS_FLASH_BASE has the final address (core view)
* CONFIG_SYS_FLASH_BASE_PHYS has the final address (IFC view)
* CONFIG_SYS_FLASH_BASE_PHYS_EARLY has the temporary IFC address
* CONFIG_SYS_TEXT_BASE is linked to 0x30000000 for booting
*/
#define CONFIG_SYS_FLASH_BASE 0x580000000ULL
#define CONFIG_SYS_FLASH_BASE_PHYS 0x80000000
#define CONFIG_SYS_FLASH_BASE_PHYS_EARLY 0x00000000
#define CONFIG_SYS_FLASH1_BASE_PHYS 0xC0000000
#define CONFIG_SYS_FLASH1_BASE_PHYS_EARLY 0x8000000
#ifndef __ASSEMBLY__
unsigned long long get_qixis_addr(void);
#endif
#define QIXIS_BASE get_qixis_addr()
#define QIXIS_BASE_PHYS 0x20000000
#define QIXIS_BASE_PHYS_EARLY 0xC000000
#define CONFIG_SYS_NAND_BASE 0x530000000ULL
#define CONFIG_SYS_NAND_BASE_PHYS 0x30000000
/* MC firmware */
/* TODO Actual DPL max length needs to be confirmed with the MC FW team */
#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
#define CONFIG_SYS_LS_MC_AIOP_IMG_MAX_LENGTH 0x200000
#define CONFIG_SYS_LS_MC_DRAM_AIOP_IMG_OFFSET 0x07000000
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
* It will be used by MC and Debug Server. The MC region must be
* 512MB aligned, so the min size to hide is 512MB.
*/
#if defined(CONFIG_FSL_MC_ENET)
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (128UL * 1024 * 1024)
#endif
/* Miscellaneous configurable options */
/* SATA */
#ifdef CONFIG_SCSI
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
#endif
/* Physical Memory Map */
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
#ifndef SPL_NO_ENV
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"loadaddr=0x80100000\0" \
"kernel_addr=0x100000\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"kernel_start=0x581000000\0" \
"kernel_load=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"console=ttyAMA0,38400n8\0" \
"mcinitcmd=fsl_mc start mc 0x580a00000" \
" 0x580e00000 \0"
#endif
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#ifdef CONFIG_SPL
#define CONFIG_SPL_BSS_START_ADDR 0x80100000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00100000
#define CONFIG_SPL_MAX_SIZE 0x16000
#define CONFIG_SPL_STACK (CONFIG_SYS_FSL_OCRAM_BASE + 0x9ff0)
#define CONFIG_SPL_TARGET "u-boot-with-spl.bin"
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00100000
#define CONFIG_SYS_SPL_MALLOC_START 0x80200000
#ifdef CONFIG_NXP_ESBC
#define CONFIG_U_BOOT_HDR_SIZE (16 << 10)
/*
* HDR would be appended at end of image and copied to DDR along
* with U-Boot image. Here u-boot max. size is 512K. So if binary
* size increases then increase this size in case of secure boot as
* it uses raw u-boot image instead of fit image.
*/
#define CONFIG_SYS_MONITOR_LEN (0x100000 + CONFIG_U_BOOT_HDR_SIZE)
#else
#define CONFIG_SYS_MONITOR_LEN 0x100000
#endif /* ifdef CONFIG_NXP_ESBC */
#endif
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
#endif /* __LS1088_COMMON_H */