u-boot/configs/colibri_vf_defconfig

104 lines
2.7 KiB
Text
Raw Normal View History

CONFIG_ARM=y
CONFIG_SKIP_LOWLEVEL_INIT=y
CONFIG_SYS_THUMB_BUILD=y
CONFIG_ARCH_VF610=y
CONFIG_TEXT_BASE=0x3f401000
CONFIG_SYS_MALLOC_LEN=0x0220000
CONFIG_NR_DRAM_BANKS=1
CONFIG_ENV_SIZE=0x20000
CONFIG_ENV_OFFSET=0x180000
CONFIG_DM_GPIO=y
CONFIG_DEFAULT_DEVICE_TREE="vf610-colibri-eval-v3"
CONFIG_SYS_PROMPT="Colibri VFxx # "
CONFIG_TARGET_COLIBRI_VF=y
CONFIG_SYS_LOAD_ADDR=0x80008000
CONFIG_SYS_MEMTEST_START=0x80010000
CONFIG_SYS_MEMTEST_END=0x87c00000
CONFIG_ENV_VARS_UBOOT_CONFIG=y
CONFIG_HAS_BOARD_SIZE_LIMIT=y
CONFIG_BOARD_SIZE_LIMIT=520192
CONFIG_BOOTDELAY=1
CONFIG_USE_BOOTCOMMAND=y
CONFIG_BOOTCOMMAND="run ubiboot || run distro_bootcmd;"
CONFIG_USE_PREBOOT=y
CONFIG_PREBOOT="test -n ${fdtfile} || setenv fdtfile ${soc}-colibri-${fdt_board}.dtb"
printk: collect printk stuff into <linux/printk.h> with loglevel support When we import code from Linux, with regular re-sync planned, we want to use printk() and pr_*(). U-Boot does not support them in a clean way. So, people end up with local macros, or compat headers here and there, then we occasionally see build errors of definition conflicts. We have include/linux/compat.h, but putting all sorts of unrelated things into a single header is just a temporal workaround. Hence this patch, to find the best home for all printk variants. If you want to use printk() and friends, please include <linux/printk.h>. This header is self-contained, and pulls in only a few headers. When I was testing this clean-up, I noticed the image size exceeded its platform limit on some boards. This is because all pr_*() that were previously defined as no-op in include/linux/mtd/mtd.h (unless CONFIG_MTD_DEBUG is set), are now enabled. To make such boards happy, this commit also implements CONFIG_LOGLEVEL. The concept is similar to the kernel parameter "loglevel". (Actually, the Kconfig help message was taken from kernel-paremeter.txt of Linux) Messages with a loglevel smaller than console loglevel will be printed. The difference is the loglevel is build-time determined. To save the image size, lower priority pr_*() are compiled out. I set the default of CONFIG_LOGLEVEL to 6, i.e. pr_notice and higher priority messages are compiled in. I adjusted CONFIG_LOGLEVEL to avoid build error for some boards. Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> [trini: Add in SPL_LOGLEVEL that is the same as LOGLEVEL] Signed-off-by: Tom Rini <trini@konsulko.com>
2017-09-16 05:10:40 +00:00
CONFIG_LOGLEVEL=3
# CONFIG_DISPLAY_BOARDINFO is not set
CONFIG_DISPLAY_BOARDINFO_LATE=y
CONFIG_ARCH_MISC_INIT=y
CONFIG_BOARD_EARLY_INIT_F=y
CONFIG_HUSH_PARSER=y
# CONFIG_SYS_LONGHELP is not set
CONFIG_SYS_PBSIZE=1056
# CONFIG_CMD_BOOTD is not set
# CONFIG_CMD_BOOTM is not set
CONFIG_CMD_BOOTZ=y
# CONFIG_CMD_ELF is not set
# CONFIG_CMD_IMI is not set
CONFIG_CMD_ASKENV=y
CONFIG_CMD_MEMTEST=y
CONFIG_CMD_DFU=y
CONFIG_CMD_DM=y
# CONFIG_CMD_FLASH is not set
CONFIG_CMD_FUSE=y
CONFIG_CMD_GPIO=y
# CONFIG_CMD_LOADB is not set
# CONFIG_CMD_LOADS is not set
CONFIG_CMD_MMC=y
CONFIG_CMD_PART=y
CONFIG_CMD_USB=y
CONFIG_CMD_USB_MASS_STORAGE=y
# CONFIG_CMD_SETEXPR is not set
CONFIG_CMD_DHCP=y
# CONFIG_CMD_NFS is not set
CONFIG_CMD_MII=y
CONFIG_CMD_PING=y
CONFIG_CMD_EXT4=y
CONFIG_CMD_FAT=y
CONFIG_CMD_FS_GENERIC=y
CONFIG_MTDIDS_DEFAULT="nand0=vf610_nfc"
CONFIG_MTDPARTS_DEFAULT="mtdparts=vf610_nfc:128k(vf-bcb)ro,1408k(u-boot)ro,512k(u-boot-env),-(ubi)"
CONFIG_CMD_UBI=y
CONFIG_OF_CONTROL=y
CONFIG_ENV_OVERWRITE=y
CONFIG_ENV_IS_IN_NAND=y
CONFIG_ENV_RANGE=0x80000
CONFIG_SYS_RELOC_GD_ENV_ADDR=y
CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG=y
CONFIG_VERSION_VARIABLE=y
CONFIG_DFU_NAND=y
CONFIG_SYS_DFU_DATA_BUF_SIZE=0x100000
CONFIG_VYBRID_GPIO=y
# CONFIG_MMC_HW_PARTITIONING is not set
CONFIG_FSL_ESDHC_IMX=y
CONFIG_MTD=y
CONFIG_DM_MTD=y
CONFIG_NAND_VF610_NFC=y
CONFIG_NAND_VF610_NFC_DT=y
CONFIG_SYS_NAND_VF610_NFC_60_ECC_BYTES=y
CONFIG_SYS_NAND_ONFI_DETECTION=y
CONFIG_MTD_UBI_FASTMAP=y
CONFIG_PHYLIB=y
CONFIG_PHY_MICREL=y
CONFIG_PHY_MICREL_KSZ8XXX=y
CONFIG_FEC_MXC=y
CONFIG_MII=y
CONFIG_PINCTRL=y
CONFIG_PINCTRL_VYBRID=y
CONFIG_DM_REGULATOR=y
CONFIG_DM_REGULATOR_FIXED=y
CONFIG_DM_SERIAL=y
CONFIG_FSL_LPUART=y
CONFIG_USB=y
CONFIG_USB_EHCI_HCD=y
CONFIG_USB_STORAGE=y
CONFIG_USB_GADGET=y
CONFIG_USB_GADGET_MANUFACTURER="Toradex"
CONFIG_USB_GADGET_VENDOR_NUM=0x1b67
CONFIG_USB_GADGET_PRODUCT_NUM=0x4000
CONFIG_CI_UDC=y
CONFIG_USB_GADGET_DOWNLOAD=y
CONFIG_OF_LIBFDT_OVERLAY=y
CONFIG_FDT_FIXUP_PARTITIONS=y
# CONFIG_EFI_LOADER is not set