Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-12 14:23:00 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/board/freescale/common/qixis.h

191 lines
5.5 KiB
C
Raw Normal View History

SPDX: Convert all of our single license tags to Linux Kernel style When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-06 21:58:06 +00:00
/* SPDX-License-Identifier: GPL-2.0+ */
powerpc/p3060qds: Add board related support for P3060QDS platform The P3060QDS is a Freescale reference board for the six-core P3060 SOC. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM for RCW Ethernet: - Eight Ethernet controllers (4x1G + 4x1G/2.5G) - Three VSC8641 PHYs on board (2xRGMII + 1xMII) - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports two dUARTs up to 115200 bps for console RapidIO: Two RapidIO, sRIO1 and sRIO2 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-22 08:51:13 +00:00
/*
* Copyright 2011 Freescale Semiconductor
Move eSDHC adapter card identification to board files The eSDHC adapter card identification and multiplexing configuration through FPGA had been implemented in both common mmc driver and fsl_esdhc driver. However it is proper to move these code to board files and do it during board initialization. The FPGA registers are also board specific. This patch is to move eSDHC adapter card identification and multiplexing configuration from mmc driver to specific board files. And the option CONFIG_FSL_ESDHC_ADAPTER_IDENT is no longer needed. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> [Rebased, Removed T1040QDS change as board does not exist] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-17 10:08:58 +00:00
* Copyright 2020 NXP
powerpc/p3060qds: Add board related support for P3060QDS platform The P3060QDS is a Freescale reference board for the six-core P3060 SOC. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM for RCW Ethernet: - Eight Ethernet controllers (4x1G + 4x1G/2.5G) - Three VSC8641 PHYs on board (2xRGMII + 1xMII) - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports two dUARTs up to 115200 bps for console RapidIO: Two RapidIO, sRIO1 and sRIO2 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-22 08:51:13 +00:00
* Author: Shengzhou Liu <Shengzhou.Liu@freescale.com>
*
* This file provides support for the QIXIS of some Freescale reference boards.
*/
#ifndef __QIXIS_H_
#define __QIXIS_H_
struct qixis {
u8 id; /* ID value uniquely identifying each QDS board type */
u8 arch; /* Board version information */
u8 scver; /* QIXIS Version Register */
u8 model; /* Information of software programming model version */
u8 tagdata;
u8 ctl_sys;
u8 aux; /* Auxiliary Register,0x06 */
u8 clk_spd;
u8 stat_dut;
u8 stat_sys;
u8 stat_alrm;
u8 present;
powerpc/board: add present2 register definition for QIXIS According to new QIXIS system definition, update QIXIS registers set to add present2 register instead of obsolete ctl_sys2. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-07 20:21:02 +00:00
u8 present2; /* Presence Status Register 2,0x0c */
powerpc/p3060qds: Add board related support for P3060QDS platform The P3060QDS is a Freescale reference board for the six-core P3060 SOC. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM for RCW Ethernet: - Eight Ethernet controllers (4x1G + 4x1G/2.5G) - Three VSC8641 PHYs on board (2xRGMII + 1xMII) - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports two dUARTs up to 115200 bps for console RapidIO: Two RapidIO, sRIO1 and sRIO2 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-22 08:51:13 +00:00
u8 rcw_ctl;
u8 ctl_led;
u8 i2cblk;
u8 rcfg_ctl; /* Reconfig Control Register,0x10 */
u8 rcfg_st;
u8 dcm_ad;
u8 dcm_da;
u8 dcmd;
u8 dmsg;
u8 gdc;
u8 gdd; /* DCM Debug Data Register,0x17 */
u8 dmack;
board: fsl: lx2160aqds: identify SDHC adapter during board init Add support for SDHC adapter identification and configuration during board init. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-17 10:08:59 +00:00
u8 res1;
u8 sdhc1;
u8 sdhc2;
u8 stat_pres3;
u8 los_stat;
u8 usb_ctl;
powerpc/p3060qds: Add board related support for P3060QDS platform The P3060QDS is a Freescale reference board for the six-core P3060 SOC. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM for RCW Ethernet: - Eight Ethernet controllers (4x1G + 4x1G/2.5G) - Three VSC8641 PHYs on board (2xRGMII + 1xMII) - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports two dUARTs up to 115200 bps for console RapidIO: Two RapidIO, sRIO1 and sRIO2 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-22 08:51:13 +00:00
u8 watch; /* Watchdog Register,0x1F */
u8 pwr_ctl[2]; /* Power Control Register,0x20 */
u8 res2[2];
u8 pwr_stat[4]; /* Power Status Register,0x24 */
u8 res3[8];
u8 clk_spd2[2]; /* SYSCLK clock Speed Register,0x30 */
u8 res4[2];
u8 sclk[3]; /* Clock Configuration Registers,0x34 */
u8 res5;
u8 dclk[3];
u8 res6;
u8 clk_dspd[3];
u8 res7;
u8 rst_ctl; /* Reset Control Register,0x40 */
u8 rst_stat; /* Reset Status Register */
u8 rst_rsn; /* Reset Reason Register */
u8 rst_frc[2]; /* Reset Force Registers,0x43 */
u8 res8[11];
u8 brdcfg[16]; /* Board Configuration Register,0x50 */
u8 dutcfg[16];
u8 rcw_ad[2]; /* RCW SRAM Address Registers,0x70 */
u8 rcw_data;
u8 res9[5];
u8 post_ctl;
u8 post_stat;
u8 post_dat[2];
u8 pi_d[4];
u8 gpio_io[4];
u8 gpio_dir[4];
u8 res10[20];
u8 rjtag_ctl;
u8 rjtag_dat;
u8 res11[2];
u8 trig_src[4];
u8 trig_dst[4];
u8 trig_stat;
u8 res12[3];
u8 trig_ctr[4];
powerpc/qixis: add clock measurement registers QIXIS includes frequency measurement functions for each major processor clock input. After reset (and after clocks are stable), QIXIS measures the clocks against a reference frequency and stores the results in CLK_FREQ registers. A base register supplies a multiplier which allows directly obtaining the measured value, without requiring knowledge of the target system or QIXIS core frequency. Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-03-25 07:40:09 +00:00
u8 res13[16];
u8 clk_freq[6]; /* Clock Measurement Registers */
u8 res_c6[8];
u8 clk_base[2]; /* Clock Frequency Base Reg */
powerpc/t1040qds: Add T1040QDS board T1040QDS is a high-performance computing evaluation, development and test platform supporting the T1040 QorIQ Power Architecture™ processor. T1040QDS board Overview ----------------------- - Four e5500 cores, each with a private 256 KB L2 cache - 256 KB shared L3 CoreNet platform cache (CPC) - Interconnect CoreNet platform - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Data Path Acceleration Architecture (DPAA) incorporating acceleration for the following functions: - Packet parsing, classification, and distribution - Queue management for scheduling, packet sequencing, and congestion management - Cryptography Acceleration - RegEx Pattern Matching Acceleration - IEEE Std 1588 support - Hardware buffer management for buffer allocation and deallocation - Ethernet interfaces - Integrated 8-port Gigabit Ethernet switch - Four 1 Gbps Ethernet controllers - SERDES Connections, 8 lanes supporting: — PCI Express: supporting Gen 1 and Gen 2; — SGMII — QSGMII — SATA 2.0 — Aurora debug with dedicated connectors - DDR Controller 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and Interleaving -IFC/Local Bus - NAND flash: 8-bit, async, up to 2GB. - NOR: 8-bit or 16-bit, non-multiplexed, up to 512MB - GASIC: Simple (minimal) target within Qixis FPGA - PromJET rapid memory download support - Ethernet - Two on-board RGMII 10/100/1G ethernet ports. - PHY #0 remains powered up during deep-sleep - QIXIS System Logic FPGA - Clocks - System and DDR clock (SYSCLK, “DDRCLK”) - SERDES clocks - Power Supplies - Video - DIU supports video at up to 1280x1024x32bpp - USB - Supports two USB 2.0 ports with integrated PHYs — Two type A ports with 5V@1.5A per port. — Second port can be converted to OTG mini-AB - SDHC - SDHC port connects directly to an adapter card slot, featuring: - Supporting SD slots for: SD, SDHC (1x, 4x, 8x) and/or MMC — Supporting eMMC memory devices - SPI - On-board support of 3 different devices and sizes - Other IO - Two Serial ports - ProfiBus port - Four I2C ports Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> [York Sun: fix conflict in boards.cfg] Acked-by-by: York Sun <yorksun@freescale.com>
2013-09-12 05:41:28 +00:00
u8 res_d0[8];
u8 cms[2]; /* Core Management Space Address Register, 0xD8 */
u8 res_c0[6];
powerpc/p3060qds: Add board related support for P3060QDS platform The P3060QDS is a Freescale reference board for the six-core P3060 SOC. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM for RCW Ethernet: - Eight Ethernet controllers (4x1G + 4x1G/2.5G) - Three VSC8641 PHYs on board (2xRGMII + 1xMII) - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports two dUARTs up to 115200 bps for console RapidIO: Two RapidIO, sRIO1 and sRIO2 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-22 08:51:13 +00:00
u8 aux2[4]; /* Auxiliary Registers,0xE0 */
u8 res14[10];
u8 aux_ad;
u8 aux_da;
u8 res15[16];
};
u8 qixis_read(unsigned int reg);
void qixis_write(unsigned int reg, u8 value);
board/freescale/common:Add support of QTAG register QIXIS FPGA's QIXIS Tag Access register (QTAG) defines TAG, VER, DATE, IMAGE fields. These fields have FPGA build version, image name and build date information. Add support to parse these fields to have complete FPGA image information. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-12-23 19:24:47 +00:00
u16 qixis_read_minor(void);
char *qixis_read_time(char *result);
char *qixis_read_tag(char *buf);
powerpc/qixis: enable qixis dump command and add switch dumping command Remove #ifdef so that "qixis dump" command is always available Add "qixis_reset switch" command to dump switch settings Qixis doesn't have 1:1 switch mapping. We need to reverse engineer from registers to figure out switch settings. Not all bits are available. Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Shaveta Leekha <shaveta@freescale.com> Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-12-23 19:25:35 +00:00
const char *byte_to_binary_mask(u8 val, u8 mask, char *buf);
board/common: Add support for QIXIS read/write using i2c QIXIS FPGA is accessable via both i2c and flash controller. Only flash controller access is supported. Add support of i2c based access. It is quite useful in the scenario where either flash controller path is broken or not present. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-23 17:59:37 +00:00
#ifdef CONFIG_SYS_I2C_FPGA_ADDR
u8 qixis_read_i2c(unsigned int reg);
void qixis_write_i2c(unsigned int reg, u8 value);
#endif
powerpc/p3060qds: Add board related support for P3060QDS platform The P3060QDS is a Freescale reference board for the six-core P3060 SOC. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM for RCW Ethernet: - Eight Ethernet controllers (4x1G + 4x1G/2.5G) - Three VSC8641 PHYs on board (2xRGMII + 1xMII) - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports two dUARTs up to 115200 bps for console RapidIO: Two RapidIO, sRIO1 and sRIO2 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-22 08:51:13 +00:00
ls102xa: qixis: Add CONFIG_QIXIS_I2C_ACCESS macro Through adding CONFIG_QIXIS_I2C_ACCESS macro, QIXIS_READ(reg)/QIXIS_WRITE(reg, value) can be used for both i2c and ifc access to QIXIS FPGA. This is more convenient for coding. Signed-off-by: Jason Jin <jason.jin@freescale.com> Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-03 07:00:46 +00:00
#if defined(CONFIG_QIXIS_I2C_ACCESS) && defined(CONFIG_SYS_I2C_FPGA_ADDR)
#define QIXIS_READ(reg) qixis_read_i2c(offsetof(struct qixis, reg))
#define QIXIS_WRITE(reg, value) \
qixis_write_i2c(offsetof(struct qixis, reg), value)
#else
powerpc/p3060qds: Add board related support for P3060QDS platform The P3060QDS is a Freescale reference board for the six-core P3060 SOC. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM for RCW Ethernet: - Eight Ethernet controllers (4x1G + 4x1G/2.5G) - Three VSC8641 PHYs on board (2xRGMII + 1xMII) - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports two dUARTs up to 115200 bps for console RapidIO: Two RapidIO, sRIO1 and sRIO2 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-22 08:51:13 +00:00
#define QIXIS_READ(reg) qixis_read(offsetof(struct qixis, reg))
#define QIXIS_WRITE(reg, value) qixis_write(offsetof(struct qixis, reg), value)
ls102xa: qixis: Add CONFIG_QIXIS_I2C_ACCESS macro Through adding CONFIG_QIXIS_I2C_ACCESS macro, QIXIS_READ(reg)/QIXIS_WRITE(reg, value) can be used for both i2c and ifc access to QIXIS FPGA. This is more convenient for coding. Signed-off-by: Jason Jin <jason.jin@freescale.com> Signed-off-by: Alison Wang <alison.wang@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-03 07:00:46 +00:00
#endif
board/common: Add support for QIXIS read/write using i2c QIXIS FPGA is accessable via both i2c and flash controller. Only flash controller access is supported. Add support of i2c based access. It is quite useful in the scenario where either flash controller path is broken or not present. Signed-off-by: Ruchika Gupta <ruchika.gupta@freescale.com> Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com> Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-23 17:59:37 +00:00
#ifdef CONFIG_SYS_I2C_FPGA_ADDR
#define QIXIS_READ_I2C(reg) qixis_read_i2c(offsetof(struct qixis, reg))
#define QIXIS_WRITE_I2C(reg, value) \
qixis_write_i2c(offsetof(struct qixis, reg), value)
#endif
powerpc/p3060qds: Add board related support for P3060QDS platform The P3060QDS is a Freescale reference board for the six-core P3060 SOC. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM for RCW Ethernet: - Eight Ethernet controllers (4x1G + 4x1G/2.5G) - Three VSC8641 PHYs on board (2xRGMII + 1xMII) - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports two dUARTs up to 115200 bps for console RapidIO: Two RapidIO, sRIO1 and sRIO2 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-22 08:51:13 +00:00
mmc: fsl_esdhc: Add adapter card type identification support Add adapter card type identification support by reading FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function, define CONFIG_FSL_ESDHC_ADAPTER_IDENT. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> [York Sun: resolve conflicts in README.fsl-esdhc] Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-22 05:57:00 +00:00
/* Use for SDHC adapter card type identification and operation */
#define QIXIS_SDID_MASK 0x07
board: fsl: lx2160aqds: identify SDHC adapter during board init Add support for SDHC adapter identification and configuration during board init. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-17 10:08:59 +00:00
mmc: fsl_esdhc: Add adapter card type identification support Add adapter card type identification support by reading FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function, define CONFIG_FSL_ESDHC_ADAPTER_IDENT. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> [York Sun: resolve conflicts in README.fsl-esdhc] Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-22 05:57:00 +00:00
#define QIXIS_ESDHC_ADAPTER_TYPE_EMMC45 0x1 /* eMMC Card Rev4.5 */
#define QIXIS_ESDHC_ADAPTER_TYPE_SDMMC_LEGACY 0x2 /* SD/MMC Legacy Card */
#define QIXIS_ESDHC_ADAPTER_TYPE_EMMC44 0x3 /* eMMC Card Rev4.4 */
#define QIXIS_ESDHC_ADAPTER_TYPE_RSV 0x4 /* Reserved */
#define QIXIS_ESDHC_ADAPTER_TYPE_MMC 0x5 /* MMC Card */
#define QIXIS_ESDHC_ADAPTER_TYPE_SD 0x6 /* SD Card Rev2.0 3.0 */
#define QIXIS_ESDHC_NO_ADAPTER 0x7 /* No Card is Present*/
mmc: fsl_esdhc: enable EVDD automatic control for SD/MMC Legacy Adapter Card When detecting SDHC Adapter Card Type 2(SD/MMC Legacy Adapter Card), enable EVDD automatic control via SDHC_VS. This could support SD card IO voltage switching for UHS-1 speed mode. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-17 02:27:48 +00:00
board: fsl: lx2160aqds: identify SDHC adapter during board init Add support for SDHC adapter identification and configuration during board init. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-06-17 10:08:59 +00:00
#define QIXIS_SDHC1_S1V3 0x80 /* SDHC1: SDHC1 3.3V power control */
#define QIXIS_SDHC1_VS 0x30 /* BRDCFG11: route to SDHC1_VS */
mmc: fsl_esdhc: Add adapter card type identification support Add adapter card type identification support by reading FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function, define CONFIG_FSL_ESDHC_ADAPTER_IDENT. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> [York Sun: resolve conflicts in README.fsl-esdhc] Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-22 05:57:00 +00:00
#define QIXIS_SDCLKIN 0x08
#define QIXIS_SDCLKOUT 0x02
mmc: fsl_esdhc: enable dat[4:7] for eMMC4.5 Adapter Card If adapter card type identification is supported for platform, we would enable dat[4:7] for eMMC4.5 Adapter Card. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-17 02:27:12 +00:00
#define QIXIS_DAT5_6_7 0X02
#define QIXIS_DAT4 0X01
mmc: fsl_esdhc: enable EVDD automatic control for SD/MMC Legacy Adapter Card When detecting SDHC Adapter Card Type 2(SD/MMC Legacy Adapter Card), enable EVDD automatic control via SDHC_VS. This could support SD card IO voltage switching for UHS-1 speed mode. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Reviewed-by: York Sun <yorksun@freescale.com>
2015-09-17 02:27:48 +00:00
#define QIXIS_EVDD_BY_SDHC_VS 0x0c
mmc: fsl_esdhc: Add adapter card type identification support Add adapter card type identification support by reading FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function, define CONFIG_FSL_ESDHC_ADAPTER_IDENT. Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com> Cc: York Sun <yorksun@freescale.com> Cc: Pantelis Antoniou <panto@antoniou-consulting.com> [York Sun: resolve conflicts in README.fsl-esdhc] Reviewed-by: York Sun <yorksun@freescale.com>
2015-04-22 05:57:00 +00:00
armv8: lx2162aqds: Add support for LX2162AQDS platform This patch add base support for LX2162AQDS board. LX2162AQDS board supports LX2162A family SoCs. This patch add basic support of platform. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com> Signed-off-by: hui.song <hui.song_1@nxp.com> Signed-off-by: Manish Tomar <manish.tomar@nxp.com> Signed-off-by: Vikas Singh <vikas.singh@nxp.com> Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com> [Rebased] Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
2020-12-04 14:47:28 +00:00
#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS) || \
defined(CONFIG_TARGET_LX2160ARDB)
#define QIXIS_XMAP_MASK 0x07
#define QIXIS_RST_CTL_RESET_EN 0x30
#define QIXIS_LBMAP_DFLTBANK 0x00
#define QIXIS_LBMAP_ALTBANK 0x20
#define QIXIS_LBMAP_QSPI 0x00
#define QIXIS_RCW_SRC_QSPI 0xff
#define QIXIS_RST_CTL_RESET 0x31
#define QIXIS_RCFG_CTL_RECONFIG_IDLE 0x20
#define QIXIS_RCFG_CTL_RECONFIG_START 0x21
#define QIXIS_RCFG_CTL_WATCHDOG_ENBLE 0x08
#define QIXIS_LBMAP_MASK 0x0f
#define QIXIS_LBMAP_SD
#define QIXIS_LBMAP_EMMC
#define QIXIS_RCW_SRC_SD 0x08
#define QIXIS_RCW_SRC_EMMC 0x09
#define NON_EXTENDED_DUTCFG
#endif
#if defined(CONFIG_TARGET_LX2160AQDS) || defined(CONFIG_TARGET_LX2162AQDS)
#define QIXIS_SDID_MASK 0x07
#define QIXIS_ESDHC_NO_ADAPTER 0x7
#endif
Convert CONFIG_ESDHC_DETECT_QUIRK to Kconfig This converts the following to Kconfig: CONFIG_ESDHC_DETECT_QUIRK Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-16 18:04:38 +00:00
/*
* implementation of CONFIG_ESDHC_DETECT_QUIRK Macro.
*/
static inline u8 qixis_esdhc_detect_quirk(void)
{
/*
* SDHC1 Card ID:
* Specifies the type of card installed in the SDHC1 adapter slot.
* 000= (reserved)
* 001= eMMC V4.5 adapter is installed.
* 010= SD/MMC 3.3V adapter is installed.
* 011= eMMC V4.4 adapter is installed.
* 100= eMMC V5.0 adapter is installed.
* 101= MMC card/Legacy (3.3V) adapter is installed.
* 110= SDCard V2/V3 adapter installed.
* 111= no adapter is installed.
*/
return ((QIXIS_READ(sdhc1) & QIXIS_SDID_MASK) !=
QIXIS_ESDHC_NO_ADAPTER);
}
powerpc/p3060qds: Add board related support for P3060QDS platform The P3060QDS is a Freescale reference board for the six-core P3060 SOC. P3060QDS Board Overview: Memory subsystem: - 2G Bytes unbuffered DDR3 SDRAM SO-DIMM(64bit bus) - 128M Bytes NOR flash single-chip memory - 16M Bytes SPI flash - 8K Bytes AT24C64 I2C EEPROM for RCW Ethernet: - Eight Ethernet controllers (4x1G + 4x1G/2.5G) - Three VSC8641 PHYs on board (2xRGMII + 1xMII) - Suport multiple Vitesse VSC8234 SGMII Cards in Slot1/2/3 PCIe: Two PCI Express 2.0 controllers/ports USB: Two USB2.0, USB1(TYPE-A) and USB2(TYPE-AB) on board I2C: Four I2C controllers UART: Supports two dUARTs up to 115200 bps for console RapidIO: Two RapidIO, sRIO1 and sRIO2 Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> Signed-off-by: York Sun <yorksun@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-22 08:51:13 +00:00
#endif
Reference in a new issue Copy permalink