6.4 KiB
I2C
{% hint style="success" %}
Learn & practice AWS Hacking:
HackTricks Training AWS Red Team Expert (ARTE)
Learn & practice GCP Hacking: 
HackTricks Training GCP Red Team Expert (GRTE)
Support HackTricks
- Check the subscription plans!
- Join the 💬 Discord group or the telegram group or follow us on Twitter 🐦 @hacktricks_live.
- Share hacking tricks by submitting PRs to the HackTricks and HackTricks Cloud github repos.
Bus Pirate
Per testare se un Bus Pirate funziona, collegare +5V con VPU e 3.3V con ADC e accedere al bus pirate (usando Tera Term ad esempio) e utilizzare il comando ~:
# Use command
HiZ>~
Disconnect any devices
Connect (Vpu to +5V) and (ADC to +3.3V)
Space to continue
# Press space
Ctrl
AUX OK
MODE LED OK
PULLUP H OK
PULLUP L OK
VREG OK
ADC and supply
5V(4.96) OK
VPU(4.96) OK
3.3V(3.26) OK
ADC(3.27) OK
Bus high
MOSI OK
CLK OK
MISO OK
CS OK
Bus Hi-Z 0
MOSI OK
CLK OK
MISO OK
CS OK
Bus Hi-Z 1
MOSI OK
CLK OK
MISO OK
CS OK
MODE and VREG LEDs should be on!
Any key to exit
#Press space
Found 0 errors.
Come puoi vedere nella riga di comando precedente, è stato detto che non sono stati trovati errori. Questo è molto utile per sapere che funziona dopo averlo acquistato o dopo aver flashato un firmware.
Per connetterti con il bus pirate puoi seguire la documentazione:
In questo caso mi connetterò a un EPROM: ATMEL901 24C256 PU27:
Per comunicare con il bus pirate ho usato Tera Term connesso alla porta COM del bus pirate con un Setup --> Porta Serial --> Velocità di 115200.
Nella seguente comunicazione puoi trovare come preparare il bus pirate per parlare I2C e come scrivere e leggere dalla memoria (I commenti appaiono usando "#", non aspettarti quella parte nella comunicazione):
# Check communication with buspirate
i
Bus Pirate v3.5
Community Firmware v7.1 - goo.gl/gCzQnW [HiZ 1-WIRE UART I2C SPI 2WIRE 3WIRE KEYB LCD PIC DIO] Bootloader v4.5
DEVID:0x0447 REVID:0x3046 (24FJ64GA00 2 B8)
http://dangerousprototypes.com
# Check voltages
I2C>v
Pinstates:
1.(BR) 2.(RD) 3.(OR) 4.(YW) 5.(GN) 6.(BL) 7.(PU) 8.(GR) 9.(WT) 0.(Blk)
GND 3.3V 5.0V ADC VPU AUX SCL SDA - -
P P P I I I I I I I
GND 3.27V 4.96V 0.00V 4.96V L H H L L
#Notice how the VPU is in 5V becausethe EPROM needs 5V signals
# Get mode options
HiZ>m
1. HiZ
2. 1-WIRE
3. UART
4. I2C
5. SPI
6. 2WIRE
7. 3WIRE
8. KEYB
9. LCD
10. PIC
11. DIO
x. exit(without change)
# Select I2C
(1)>4
I2C mode:
1. Software
2. Hardware
# Select Software mode
(1)>1
Set speed:
1. ~5kHz
2. ~50kHz
3. ~100kHz
4. ~240kHz
# Select communication spped
(1)> 2
Clutch disengaged!!!
To finish setup, start up the power supplies with command 'W'
Ready
# Start communication
I2C>W
POWER SUPPLIES ON
Clutch engaged!!!
# Get macros
I2C>(0)
0.Macro menu
1.7bit address search
2.I2C sniffer
#Get addresses of slaves connected
I2C>(1)
Searching I2C address space. Found devices at:
0xA0(0x50 W) 0xA1(0x50 R)
# Note that each slave will have a write address and a read address
# 0xA0 ad 0xA1 in the previous case
# Write "BBB" in address 0x69
I2C>[0xA0 0x00 0x69 0x42 0x42 0x42]
I2C START BIT
WRITE: 0xA0 ACK
WRITE: 0x00 ACK
WRITE: 0x69 ACK
WRITE: 0x42 ACK
WRITE: 0x42 ACK
WRITE: 0x42 ACK
I2C STOP BIT
# Prepare to read from address 0x69
I2C>[0xA0 0x00 0x69]
I2C START BIT
WRITE: 0xA0 ACK
WRITE: 0x00 ACK
WRITE: 0x69 ACK
I2C STOP BIT
# Read 20B from address 0x69 configured before
I2C>[0xA1 r:20]
I2C START BIT
WRITE: 0xA1 ACK
READ: 0x42 ACK 0x42 ACK 0x42 ACK 0x20 ACK 0x48 ACK 0x69 ACK 0x20 ACK 0x44 ACK 0x72 ACK 0x65 ACK 0x67 ACK 0x21 ACK 0x20 ACK 0x41 ACK 0x41 ACK 0x41 ACK 0x00 ACK 0xFF ACK 0xFF ACK 0xFF
NACK
Sniffer
In questo scenario andremo a sniffare la comunicazione I2C tra l'arduino e l'EPROM precedente, devi solo comunicare tra i due dispositivi e poi collegare il bus pirate ai pin SCL, SDA e GND:
I2C>m
1. HiZ
2. 1-WIRE
3. UART
4. I2C
5. SPI
6. 2WIRE
7. 3WIRE
8. KEYB
9. LCD
10. PIC
11. DIO
x. exit(without change)
(1)>4
I2C mode:
1. Software
2. Hardware
(1)>1
Set speed:
1. ~5kHz
2. ~50kHz
3. ~100kHz
4. ~240kHz
(1)>1
Clutch disengaged!!!
To finish setup, start up the power supplies with command 'W'
Ready
# EVEN IF YOU ARE GOING TO SNIFF YOU NEED TO POWER ON!
I2C>W
POWER SUPPLIES ON
Clutch engaged!!!
# Start sniffing, you can see we sniffed a write command
I2C>(2)
Sniffer
Any key to exit
[0xA0+0x00+0x69+0x41+0x41+0x41+0x20+0x48+0x69+0x20+0x44+0x72+0x65+0x67+0x21+0x20+0x41+0x41+0x41+0x00+]
{% hint style="success" %}
Impara e pratica il hacking AWS:HackTricks Training AWS Red Team Expert (ARTE)
Impara e pratica il hacking GCP: HackTricks Training GCP Red Team Expert (GRTE)
Supporta HackTricks
- Controlla i piani di abbonamento!
- Unisciti al 💬 gruppo Discord o al gruppo telegram o seguici su Twitter 🐦 @hacktricks_live.
- Condividi trucchi di hacking inviando PR ai HackTricks e HackTricks Cloud repos su github.