#include /* ========================== DATA RATE SETTINGS =============================== * * This is how to configure registers MDMCFG3 and MDMCFG4. * * MDMCFG3 is the data rate mantissa, the exponent is in MDMCFG4, * last 4 bits of the register. * * The rate (assuming 26Mhz crystal) is calculated as follows: * * ((256+MDMCFG3)*(2^MDMCFG4:0..3bits)) / 2^28 * 26000000. * * For instance for the default values of MDMCFG3[0..3] (34) and MDMCFG4 (12): * * ((256+34)*(2^12))/(2^28)*26000000 = 115051.2688000000, that is 115KBaud * * ============================ BANDWIDTH FILTER =============================== * * Bandwidth filter setting: * * BW filter as just 16 possibilities depending on how the first nibble * (first 4 bits) of the MDMCFG4 bits are set. Instead of providing the * formula, it is simpler to show all the values of the nibble and the * corresponding bandwidth filter. * * 0 812khz * 1 650khz * 2 541khz * 3 464khz * 4 406khz * 5 325khz * 6 270khz * 7 232khz * 8 203khz * 9 162khz * a 135khz * b 116khz * c 102khz * d 82 khz * e 68 khz * f 58 khz * * ============================== FSK DEVIATION ================================ * * FSK deviation is controlled by the DEVIATION register. In Ruby: * * dev = (26000000.0/2**17)*(8+(deviation&7))*(2**(deviation>>4&7)) * * deviation&7 (last three bits) is the deviation mantissa, while * deviation>>4&7 (bits 6,5,4) are the exponent. * * Deviations values according to certain configuration of DEVIATION: * * 0x04 -> 2.380371 kHz * 0x24 -> 9.521484 kHz * 0x34 -> 19.042969 Khz * 0x40 -> 25.390625 Khz * 0x43 -> 34.912109 Khz * 0x45 -> 41.259765 Khz * 0x47 -> 47.607422 kHz */ /* 20 KBaud, 2FSK, 28.56 kHz deviation, 325 Khz bandwidth filter. */ static uint8_t protoview_subghz_tpms1_fsk_async_regs[][2] = { /* GPIO GD0 */ {CC1101_IOCFG0, 0x0D}, // GD0 as async serial data output/input /* Frequency Synthesizer Control */ {CC1101_FSCTRL1, 0x06}, // IF = (26*10^6) / (2^10) * 0x06 = 152343.75Hz /* Packet engine */ {CC1101_PKTCTRL0, 0x32}, // Async, continious, no whitening {CC1101_PKTCTRL1, 0x04}, // // Modem Configuration {CC1101_MDMCFG0, 0x00}, {CC1101_MDMCFG1, 0x02}, {CC1101_MDMCFG2, 0x04}, // Format 2-FSK/FM, No preamble/sync, Disable (current optimized). Other code reading TPMS uses GFSK, but should be the same when in RX mode. {CC1101_MDMCFG3, 0x93}, // Data rate is 20kBaud {CC1101_MDMCFG4, 0x59}, // Rx bandwidth filter is 325 kHz {CC1101_DEVIATN, 0x41}, // Deviation 28.56 kHz /* Main Radio Control State Machine */ {CC1101_MCSM0, 0x18}, // Autocalibrate on idle-to-rx/tx, PO_TIMEOUT is 64 cycles(149-155us) /* Frequency Offset Compensation Configuration */ {CC1101_FOCCFG, 0x16}, // no frequency offset compensation, POST_K same as PRE_K, PRE_K is 4K, GATE is off /* Automatic Gain Control */ {CC1101_AGCCTRL0, 0x91}, //10 - Medium hysteresis, medium asymmetric dead zone, medium gain ; 01 - 16 samples agc; 00 - Normal AGC, 01 - 8dB boundary {CC1101_AGCCTRL1, 0x00}, // 0; 0 - LNA 2 gain is decreased to minimum before decreasing LNA gain; 00 - Relative carrier sense threshold disabled; 0000 - RSSI to MAIN_TARGET {CC1101_AGCCTRL2, 0x07}, // 00 - DVGA all; 000 - MAX LNA+LNA2; 111 - MAIN_TARGET 42 dB /* Wake on radio and timeouts control */ {CC1101_WORCTRL, 0xFB}, // WOR_RES is 2^15 periods (0.91 - 0.94 s) 16.5 - 17.2 hours /* Frontend configuration */ {CC1101_FREND0, 0x10}, // Adjusts current TX LO buffer {CC1101_FREND1, 0x56}, /* End */ {0, 0}, /* CC1101 2FSK PATABLE. */ {0xC0, 0}, {0, 0}, {0, 0}, {0, 0}}; /* This is like the default Flipper OOK 640Khz bandwidth preset, but * the bandwidth is changed to 10kBaud to accomodate TPMS frequency. */ static const uint8_t protoview_subghz_tpms2_ook_async_regs[][2] = { /* GPIO GD0 */ {CC1101_IOCFG0, 0x0D}, // GD0 as async serial data output/input /* FIFO and internals */ {CC1101_FIFOTHR, 0x07}, // The only important bit is ADC_RETENTION /* Packet engine */ {CC1101_PKTCTRL0, 0x32}, // Async, continious, no whitening /* Frequency Synthesizer Control */ {CC1101_FSCTRL1, 0x06}, // IF = (26*10^6) / (2^10) * 0x06 = 152343.75Hz // Modem Configuration {CC1101_MDMCFG0, 0x00}, // Channel spacing is 25kHz {CC1101_MDMCFG1, 0x00}, // Channel spacing is 25kHz {CC1101_MDMCFG2, 0x30}, // Format ASK/OOK, No preamble/sync {CC1101_MDMCFG3, 0x93}, // Data rate is 10kBaud {CC1101_MDMCFG4, 0x18}, // Rx BW filter is 650.000kHz /* Main Radio Control State Machine */ {CC1101_MCSM0, 0x18}, // Autocalibrate on idle-to-rx/tx, PO_TIMEOUT is 64 cycles(149-155us) /* Frequency Offset Compensation Configuration */ {CC1101_FOCCFG, 0x18}, // no frequency offset compensation, POST_K same as PRE_K, PRE_K is 4K, GATE is off /* Automatic Gain Control */ {CC1101_AGCCTRL0, 0x91}, // 10 - Medium hysteresis, medium asymmetric dead zone, medium gain ; 01 - 16 samples agc; 00 - Normal AGC, 01 - 8dB boundary {CC1101_AGCCTRL1, 0x0}, // 0; 0 - LNA 2 gain is decreased to minimum before decreasing LNA gain; 00 - Relative carrier sense threshold disabled; 0000 - RSSI to MAIN_TARGET {CC1101_AGCCTRL2, 0x07}, // 00 - DVGA all; 000 - MAX LNA+LNA2; 111 - MAIN_TARGET 42 dB /* Wake on radio and timeouts control */ {CC1101_WORCTRL, 0xFB}, // WOR_RES is 2^15 periods (0.91 - 0.94 s) 16.5 - 17.2 hours /* Frontend configuration */ {CC1101_FREND0, 0x11}, // Adjusts current TX LO buffer + high is PATABLE[1] {CC1101_FREND1, 0xB6}, // /* End */ {0, 0}, /* CC1101 OOK PATABLE. */ {0, 0xC0}, {0, 0}, {0, 0}, {0, 0}}; /* GFSK 19k dev, 325 Khz filter, 20kBaud. Different AGI settings. * Works well with Toyota. */ static uint8_t protoview_subghz_tpms3_gfsk_async_regs[][2] = { /* GPIO GD0 */ {CC1101_IOCFG0, 0x0D}, // GD0 as async serial data output/input /* Frequency Synthesizer Control */ {CC1101_FSCTRL1, 0x06}, // IF = (26*10^6) / (2^10) * 0x06 = 152343.75Hz /* Packet engine */ {CC1101_PKTCTRL0, 0x32}, // Async, continious, no whitening {CC1101_PKTCTRL1, 0x04}, // // Modem Configuration {CC1101_MDMCFG0, 0x00}, {CC1101_MDMCFG1, 0x02}, // 2 is the channel spacing exponet: not used {CC1101_MDMCFG2, 0x10}, // GFSK without any other check {CC1101_MDMCFG3, 0x93}, // Data rate is 20kBaud {CC1101_MDMCFG4, 0x59}, // Rx bandwidth filter is 325 kHz {CC1101_DEVIATN, 0x34}, // Deviation 19.04 Khz. /* Main Radio Control State Machine */ {CC1101_MCSM0, 0x18}, // Autocalibrate on idle-to-rx/tx, PO_TIMEOUT is 64 cycles(149-155us) /* Frequency Offset Compensation Configuration */ {CC1101_FOCCFG, 0x16}, // no frequency offset compensation, POST_K same as PRE_K, PRE_K is 4K, GATE is off /* Automatic Gain Control */ {CC1101_AGCCTRL0, 0x80}, {CC1101_AGCCTRL1, 0x58}, {CC1101_AGCCTRL2, 0x87}, /* Wake on radio and timeouts control */ {CC1101_WORCTRL, 0xFB}, // WOR_RES is 2^15 periods (0.91 - 0.94 s) 16.5 - 17.2 hours /* Frontend configuration */ {CC1101_FREND0, 0x10}, // Adjusts current TX LO buffer {CC1101_FREND1, 0x56}, /* End */ {0, 0}, /* CC1101 2FSK PATABLE. */ {0xC0, 0}, {0, 0}, {0, 0}, {0, 0}}; /* 40 KBaud, 2FSK, 28 kHz deviation, 270 Khz bandwidth filter. */ static uint8_t protoview_subghz_40k_fsk_async_regs[][2] = { /* GPIO GD0 */ {CC1101_IOCFG0, 0x0D}, // GD0 as async serial data output/input /* Frequency Synthesizer Control */ {CC1101_FSCTRL1, 0x06}, // IF = (26*10^6) / (2^10) * 0x06 = 152343.75Hz /* Packet engine */ {CC1101_PKTCTRL0, 0x32}, // Async, continious, no whitening {CC1101_PKTCTRL1, 0x04}, // // Modem Configuration {CC1101_MDMCFG0, 0x00}, {CC1101_MDMCFG1, 0x02}, {CC1101_MDMCFG2, 0x04}, // Format 2-FSK/FM, No preamble/sync, Disable (current optimized). Other code reading TPMS uses GFSK, but should be the same when in RX mode. {CC1101_MDMCFG3, 0x93}, // Data rate is 40kBaud {CC1101_MDMCFG4, 0x6A}, // 6 = BW filter 270kHz, A = Data rate exp {CC1101_DEVIATN, 0x41}, // Deviation 28kHz /* Main Radio Control State Machine */ {CC1101_MCSM0, 0x18}, // Autocalibrate on idle-to-rx/tx, PO_TIMEOUT is 64 cycles(149-155us) /* Frequency Offset Compensation Configuration */ {CC1101_FOCCFG, 0x16}, // no frequency offset compensation, POST_K same as PRE_K, PRE_K is 4K, GATE is off /* Automatic Gain Control */ {CC1101_AGCCTRL0, 0x91}, //10 - Medium hysteresis, medium asymmetric dead zone, medium gain ; 01 - 16 samples agc; 00 - Normal AGC, 01 - 8dB boundary {CC1101_AGCCTRL1, 0x00}, // 0; 0 - LNA 2 gain is decreased to minimum before decreasing LNA gain; 00 - Relative carrier sense threshold disabled; 0000 - RSSI to MAIN_TARGET {CC1101_AGCCTRL2, 0x07}, // 00 - DVGA all; 000 - MAX LNA+LNA2; 111 - MAIN_TARGET 42 dB /* Wake on radio and timeouts control */ {CC1101_WORCTRL, 0xFB}, // WOR_RES is 2^15 periods (0.91 - 0.94 s) 16.5 - 17.2 hours /* Frontend configuration */ {CC1101_FREND0, 0x10}, // Adjusts current TX LO buffer {CC1101_FREND1, 0x56}, /* End */ {0, 0}, /* CC1101 2FSK PATABLE. */ {0xC0, 0}, {0, 0}, {0, 0}, {0, 0}}; /* This is like the default Flipper OOK 640Khz bandwidth preset, but * the bandwidth is changed to 40kBaud, in order to receive signals * with a pulse width ~25us/30us. */ static const uint8_t protoview_subghz_40k_ook_async_regs[][2] = { /* GPIO GD0 */ {CC1101_IOCFG0, 0x0D}, // GD0 as async serial data output/input /* FIFO and internals */ {CC1101_FIFOTHR, 0x07}, // The only important bit is ADC_RETENTION /* Packet engine */ {CC1101_PKTCTRL0, 0x32}, // Async, continious, no whitening /* Frequency Synthesizer Control */ {CC1101_FSCTRL1, 0x06}, // IF = (26*10^6) / (2^10) * 0x06 = 152343.75Hz // Modem Configuration {CC1101_MDMCFG0, 0x00}, // Channel spacing is 25kHz {CC1101_MDMCFG1, 0x00}, // Channel spacing is 25kHz {CC1101_MDMCFG2, 0x30}, // Format ASK/OOK, No preamble/sync {CC1101_MDMCFG3, 0x93}, // Data rate is 40kBaud {CC1101_MDMCFG4, 0x1A}, // Rx BW filter is 650.000kHz /* Main Radio Control State Machine */ {CC1101_MCSM0, 0x18}, // Autocalibrate on idle-to-rx/tx, PO_TIMEOUT is 64 cycles(149-155us) /* Frequency Offset Compensation Configuration */ {CC1101_FOCCFG, 0x18}, // no frequency offset compensation, POST_K same as PRE_K, PRE_K is 4K, GATE is off /* Automatic Gain Control */ {CC1101_AGCCTRL0, 0x91}, // 10 - Medium hysteresis, medium asymmetric dead zone, medium gain ; 01 - 16 samples agc; 00 - Normal AGC, 01 - 8dB boundary {CC1101_AGCCTRL1, 0x0}, // 0; 0 - LNA 2 gain is decreased to minimum before decreasing LNA gain; 00 - Relative carrier sense threshold disabled; 0000 - RSSI to MAIN_TARGET {CC1101_AGCCTRL2, 0x07}, // 00 - DVGA all; 000 - MAX LNA+LNA2; 111 - MAIN_TARGET 42 dB /* Wake on radio and timeouts control */ {CC1101_WORCTRL, 0xFB}, // WOR_RES is 2^15 periods (0.91 - 0.94 s) 16.5 - 17.2 hours /* Frontend configuration */ {CC1101_FREND0, 0x11}, // Adjusts current TX LO buffer + high is PATABLE[1] {CC1101_FREND1, 0xB6}, // /* End */ {0, 0}, /* CC1101 OOK PATABLE. */ {0, 0xC0}, {0, 0}, {0, 0}, {0, 0}};