u-boot/include/configs/dragonboard410c.h
Alex Kiernan 623de3f086 Convert CONFIG_SUPPORT_EMMC_BOOT to Kconfig
This converts the following to Kconfig:
   CONFIG_SUPPORT_EMMC_BOOT

As requested by Michal Simek <michal.simek@xilinx.com>, these boards
have no eMMC so CONFIG_SUPPORT_EMMC_BOOT has not been migrated:

  xilinx_zynqmp_zc1275_revB
  xilinx_zynqmp_zc1751_xm018_dc4
  xilinx_zynqmp_zc1751_xm019_dc5
  xilinx_zynqmp_zcu100_revC
  xilinx_zynqmp_zcu102_rev1_0
  xilinx_zynqmp_zcu102_revA
  xilinx_zynqmp_zcu102_revB
  xilinx_zynqmp_zcu104_revA
  xilinx_zynqmp_zcu104_revC
  xilinx_zynqmp_zcu106_revA
  xilinx_zynqmp_zcu111_revA

Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
2019-05-04 13:04:12 -04:00

96 lines
2.7 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Board configuration file for Dragonboard 410C
*
* (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
*/
#ifndef __CONFIGS_DRAGONBOARD410C_H
#define __CONFIGS_DRAGONBOARD410C_H
#include <linux/sizes.h>
#include <asm/arch/sysmap-apq8016.h>
/* Physical Memory Map */
#define PHYS_SDRAM_1 0x80000000
/* 1008 MB (the last ~30Mb are secured for TrustZone by ATF*/
#define PHYS_SDRAM_1_SIZE 0x3da00000
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_SDRAM_BASE + 0x7fff0)
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x80000)
#define CONFIG_SYS_BOOTM_LEN SZ_64M
/* UART */
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY 19000000
#define CONFIG_SYS_LDSCRIPT "board/qualcomm/dragonboard410c/u-boot.lds"
/* Fixup - in init code we switch from device to host mode,
* it has to be done after each HCD reset */
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
/* BOOTP options */
#define CONFIG_BOOTP_BOOTFILESIZE
#define BOOT_TARGET_DEVICES(func) \
func(USB, usb, 0) \
func(MMC, mmc, 1) \
func(MMC, mmc, 0) \
func(DHCP, dhcp, na)
#include <config_distro_bootcmd.h>
/* Does what recovery does */
#define REFLASH(file, part) \
"part start mmc 0 "#part" start && "\
"part size mmc 0 "#part" size && "\
"tftp $loadaddr "#file" && " \
"mmc write $loadaddr $start $size && "
#define CONFIG_ENV_REFLASH \
"mmc dev 0 && "\
"usb start && "\
"dhcp && "\
"tftp $loadaddr dragonboard/rescue/gpt_both0.bin && "\
"mmc write $loadaddr 0 43 && " \
"mmc rescan && "\
REFLASH(dragonboard/rescue/NON-HLOS.bin, 1)\
REFLASH(dragonboard/rescue/sbl1.mbn, 2)\
REFLASH(dragonboard/rescue/rpm.mbn, 3)\
REFLASH(dragonboard/rescue/tz.mbn, 4)\
REFLASH(dragonboard/rescue/hyp.mbn, 5)\
REFLASH(dragonboard/rescue/sec.dat, 6)\
REFLASH(dragonboard/rescue/emmc_appsboot.mbn, 7)\
REFLASH(dragonboard/u-boot.img, 8)\
"usb stop &&"\
"echo Reflash completed"
/* Environment */
#define CONFIG_EXTRA_ENV_SETTINGS \
"reflash="CONFIG_ENV_REFLASH"\0"\
"loadaddr=0x81000000\0" \
"fdt_high=0xffffffffffffffff\0" \
"initrd_high=0xffffffffffffffff\0" \
"linux_image=Image\0" \
"kernel_addr_r=0x81000000\0"\
"fdtfile=qcom/apq8016-sbc.dtb\0" \
"fdt_addr_r=0x83000000\0"\
"ramdisk_addr_r=0x84000000\0"\
"scriptaddr=0x90000000\0"\
"pxefile_addr_r=0x90100000\0"\
BOOTENV
#define CONFIG_ENV_SIZE 0x2000
#define CONFIG_SYS_MMC_ENV_DEV 0 /* mmc0 = emmc, mmc1 = sd */
#define CONFIG_SYS_MMC_ENV_PART 2 /* Set env partition to BOOT2 partition */
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + SZ_8M)
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#endif