mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-16 08:13:17 +00:00
3619e94ad7
Current document about how to boot VxWorks is limited. Add several chapters in README.vxworks to document this. Signed-off-by: Bin Meng <bmeng.cn@gmail.com> Reviewed-by: Tom Rini <trini@konsulko.com>
85 lines
3.6 KiB
Text
85 lines
3.6 KiB
Text
#
|
|
# Copyright (C) 2013, Miao Yan <miao.yan@windriver.com>
|
|
# Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com>
|
|
#
|
|
# SPDX-License-Identifier: GPL-2.0+
|
|
#
|
|
|
|
VxWorks Support
|
|
===============
|
|
|
|
This document describes the information about U-Boot loading VxWorks kernel.
|
|
|
|
Status
|
|
------
|
|
U-Boot supports loading VxWorks kernels via 'bootvx' and 'bootm' commands.
|
|
For booting old kernels (6.9.x) on PowerPC and ARM, and all kernel versions
|
|
on other architectures, 'bootvx' shall be used. For booting VxWorks 7 kernels
|
|
on PowerPC and ARM, 'bootm' shall be used.
|
|
|
|
64-bit x86 kernel cannot be loaded as of today.
|
|
|
|
VxWork 7 on PowerPC and ARM
|
|
---------------------------
|
|
From VxWorks 7, VxWorks starts adopting device tree as its hardware decription
|
|
mechansim (for PowerPC and ARM), thus requiring boot interface changes.
|
|
This section will describe the new interface.
|
|
|
|
For PowerPC, the calling convention of the new VxWorks entry point conforms to
|
|
the ePAPR standard, which is shown below (see ePAPR for more details):
|
|
|
|
void (*kernel_entry)(fdt_addr, 0, 0, EPAPR_MAGIC, boot_IMA, 0, 0)
|
|
|
|
For ARM, the calling convention is show below:
|
|
|
|
void (*kernel_entry)(void *fdt_addr)
|
|
|
|
When booting new VxWorks kernel (uImage format), the parameters passed to bootm
|
|
is like below:
|
|
|
|
bootm <kernel image address> - <device tree address>
|
|
|
|
VxWorks bootline
|
|
----------------
|
|
When using 'bootvx', the kernel bootline must be prepared by U-Boot at a
|
|
board-specific address before loading VxWorks. U-Boot supplies its address
|
|
via "bootaddr" environment variable. To check where the bootline should be
|
|
for a specific board, go to the VxWorks BSP for that board, and look for a
|
|
parameter called BOOT_LINE_ADRS. Assign its value to "bootaddr". A typical
|
|
value for "bootaddr" is 0x101200.
|
|
|
|
If a "bootargs" variable is defined, its content will be copied to the memory
|
|
location pointed by "bootaddr" as the kernel bootline. If "bootargs" is not
|
|
there, command 'bootvx' can construct a valid bootline using the following
|
|
environments variables: bootdev, bootfile, ipaddr, netmask, serverip,
|
|
gatewayip, hostname, othbootargs.
|
|
|
|
When using 'bootm', just define "bootargs" in the environment and U-Boot will
|
|
handle bootline fix up for the kernel dtb automatically.
|
|
|
|
Serial console
|
|
--------------
|
|
It's very common that VxWorks BSPs configure a different baud rate for the
|
|
serial console from what is being used by U-Boot. For example, VxWorks tends
|
|
to use 9600 as the default baud rate on all x86 BSPs while U-Boot uses 115200.
|
|
Please configure both U-Boot and VxWorks to use the same baud rate, or it may
|
|
look like VxWorks hangs somewhere as nothing outputs on the serial console.
|
|
|
|
x86-specific information
|
|
------------------------
|
|
Before loading an x86 kernel, two additional environment variables need to be
|
|
provided. They are "e820data" and "e820info", which represent the address of
|
|
E820 table and E820 information (defined by VxWorks) in system memory.
|
|
|
|
Check VxWorks kernel configuration to look for BIOS_E820_DATA_START and
|
|
BIOS_E820_INFO_START, and assign their values to "e820data" and "e820info"
|
|
accordingly. If neither of these two are supplied, U-Boot assumes a default
|
|
location at 0x4000 for "e820data" and 0x4a00 for "e820info". Typical values
|
|
for "e820data" and "e820info" are 0x104000 and 0x104a00. But there is one
|
|
exception on Intel Galileo, where "e820data" and "e820info" should be left
|
|
unset, which assume the default location for VxWorks.
|
|
|
|
Note since currently U-Boot does not support ACPI yet, VxWorks kernel must
|
|
be configured to use MP table and virtual wire interrupt mode. This requires
|
|
INCLUDE_MPTABLE_BOOT_OP and INCLUDE_VIRTUAL_WIRE_MODE to be included in a
|
|
VxWorks kernel configuration.
|