mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-26 04:53:42 +00:00
83d290c56f
When U-Boot started using SPDX tags we were among the early adopters and there weren't a lot of other examples to borrow from. So we picked the area of the file that usually had a full license text and replaced it with an appropriate SPDX-License-Identifier: entry. Since then, the Linux Kernel has adopted SPDX tags and they place it as the very first line in a file (except where shebangs are used, then it's second line) and with slightly different comment styles than us. In part due to community overlap, in part due to better tag visibility and in part for other minor reasons, switch over to that style. This commit changes all instances where we have a single declared license in the tag as both the before and after are identical in tag contents. There's also a few places where I found we did not have a tag and have introduced one. Signed-off-by: Tom Rini <trini@konsulko.com>
150 lines
4 KiB
C
150 lines
4 KiB
C
/* SPDX-License-Identifier: GPL-2.0 */
|
|
/*
|
|
* Copyright (C) Marvell International Ltd. and its affiliates
|
|
*/
|
|
|
|
#ifndef __DDR3_AXP_CONFIG_H
|
|
#define __DDR3_AXP_CONFIG_H
|
|
|
|
/*
|
|
* DDR3_LOG_LEVEL Information
|
|
*
|
|
* Level 0: Provides an error code in a case of failure, RL, WL errors
|
|
* and other algorithm failure
|
|
* Level 1: Provides the D-Unit setup (SPD/Static configuration)
|
|
* Level 2: Provides the windows margin as a results of DQS centeralization
|
|
* Level 3: Provides the windows margin of each DQ as a results of DQS
|
|
* centeralization
|
|
*/
|
|
#ifdef CONFIG_DDR_LOG_LEVEL
|
|
#define DDR3_LOG_LEVEL CONFIG_DDR_LOG_LEVEL
|
|
#else
|
|
#define DDR3_LOG_LEVEL 0
|
|
#endif
|
|
|
|
#define DDR3_PBS 1
|
|
|
|
/* This flag allows the execution of SW WL/RL upon HW failure */
|
|
#define DDR3_RUN_SW_WHEN_HW_FAIL 1
|
|
|
|
/*
|
|
* General Configurations
|
|
*
|
|
* The following parameters are required for proper setup:
|
|
*
|
|
* DDR_TARGET_FABRIC - Set desired fabric configuration
|
|
* (for sample@Reset fabfreq parameter)
|
|
* DRAM_ECC - Set ECC support 1/0
|
|
* BUS_WIDTH - 64/32 bit
|
|
* CONFIG_SPD_EEPROM - Enables auto detection of DIMMs and their timing values
|
|
* DQS_CLK_ALIGNED - Set this if CLK and DQS signals are aligned on board
|
|
* MIXED_DIMM_STATIC - Mixed DIMM + On board devices support (ODT registers
|
|
* values are taken statically)
|
|
* DDR3_TRAINING_DEBUG - Debug prints of internal code
|
|
*/
|
|
#define DDR_TARGET_FABRIC 5
|
|
/* Only enable ECC if the board selects it */
|
|
#ifdef CONFIG_BOARD_ECC_SUPPORT
|
|
#define DRAM_ECC 1
|
|
#else
|
|
#define DRAM_ECC 0
|
|
#endif
|
|
|
|
#ifdef CONFIG_DDR_32BIT
|
|
#define BUS_WIDTH 32
|
|
#else
|
|
#define BUS_WIDTH 64
|
|
#endif
|
|
|
|
#undef DQS_CLK_ALIGNED
|
|
#undef MIXED_DIMM_STATIC
|
|
#define DDR3_TRAINING_DEBUG 0
|
|
#define REG_DIMM_SKIP_WL 0
|
|
|
|
/* Marvell boards specific configurations */
|
|
#if defined(DB_78X60_PCAC)
|
|
#undef CONFIG_SPD_EEPROM
|
|
#define STATIC_TRAINING
|
|
#endif
|
|
|
|
#if defined(DB_78X60_AMC)
|
|
#undef CONFIG_SPD_EEPROM
|
|
#undef DRAM_ECC
|
|
#define DRAM_ECC 1
|
|
#endif
|
|
|
|
#ifdef CONFIG_SPD_EEPROM
|
|
/*
|
|
* DIMM support parameters:
|
|
* DRAM_2T - Set Desired 2T Mode - 0 - 1T, 0x1 - 2T, 0x2 - 3T
|
|
* DIMM_CS_BITMAP - bitmap representing the optional CS in DIMMs
|
|
* (0xF=CS0+CS1+CS2+CS3, 0xC=CS2+CS3...)
|
|
*/
|
|
#define DRAM_2T 0x0
|
|
#define DIMM_CS_BITMAP 0xF
|
|
#define DUNIT_SPD
|
|
#endif
|
|
|
|
#ifdef DRAM_ECC
|
|
/*
|
|
* ECC support parameters:
|
|
*
|
|
* U_BOOT_START_ADDR, U_BOOT_SCRUB_SIZE - relevant when using ECC and need
|
|
* to configure the scrubbing area
|
|
*/
|
|
#define TRAINING_SIZE 0x20000
|
|
#define U_BOOT_START_ADDR 0
|
|
#define U_BOOT_SCRUB_SIZE 0x1000000 /* TRAINING_SIZE */
|
|
#endif
|
|
|
|
/*
|
|
* Registered DIMM Support - In case registered DIMM is attached,
|
|
* please supply the following values:
|
|
* (see JEDEC - JESD82-29A "Definition of the SSTE32882 Registering Clock
|
|
* Driver with Parity and Quad Chip
|
|
* Selects for DDR3/DDR3L/DDR3U RDIMM 1.5 V/1.35 V/1.25 V Applications")
|
|
* RC0: Global Features Control Word
|
|
* RC1: Clock Driver Enable Control Word
|
|
* RC2: Timing Control Word
|
|
* RC3-RC5 - taken from SPD
|
|
* RC8: Additional IBT Setting Control Word
|
|
* RC9: Power Saving Settings Control Word
|
|
* RC10: Encoding for RDIMM Operating Speed
|
|
* RC11: Operating Voltage VDD and VREFCA Control Word
|
|
*/
|
|
#define RDIMM_RC0 0
|
|
#define RDIMM_RC1 0
|
|
#define RDIMM_RC2 0
|
|
#define RDIMM_RC8 0
|
|
#define RDIMM_RC9 0
|
|
#define RDIMM_RC10 0x2
|
|
#define RDIMM_RC11 0x0
|
|
|
|
#if defined(MIXED_DIMM_STATIC) || !defined(CONFIG_SPD_EEPROM)
|
|
#define DUNIT_STATIC
|
|
#endif
|
|
|
|
#if defined(MIXED_DIMM_STATIC) || defined(CONFIG_SPD_EEPROM)
|
|
/*
|
|
* This flag allows the user to change the dram refresh cycle in ps,
|
|
* only in case of SPD or MIX DIMM topology
|
|
*/
|
|
#define TREFI_USER_EN
|
|
|
|
#ifdef TREFI_USER_EN
|
|
#define TREFI_USER 3900000
|
|
#endif
|
|
#endif
|
|
|
|
#ifdef CONFIG_SPD_EEPROM
|
|
/*
|
|
* AUTO_DETECTION_SUPPORT - relevant ONLY for Marvell DB boards.
|
|
* Enables I2C auto detection different options
|
|
*/
|
|
#if defined(CONFIG_DB_88F78X60) || defined(CONFIG_DB_88F78X60_REV2) || \
|
|
defined(CONFIG_DB_784MP_GP)
|
|
#define AUTO_DETECTION_SUPPORT
|
|
#endif
|
|
#endif
|
|
|
|
#endif /* __DDR3_AXP_CONFIG_H */
|