mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-11 07:34:31 +00:00
cdb23792e8
Remove platform CONFIG_SYS_HZ definition for configs A-Z*. Signed-off-by: Rob Herring <rob.herring@calxeda.com>
384 lines
13 KiB
C
384 lines
13 KiB
C
/*
|
|
* (C) Copyright 2000
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
/*
|
|
* board/config.h - configuration options, board specific
|
|
*/
|
|
|
|
#ifndef __CONFIG_H
|
|
#define __CONFIG_H
|
|
|
|
/*
|
|
* High Level Configuration Options
|
|
* (easy to change)
|
|
*/
|
|
|
|
#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
|
|
#define CONFIG_MVS 1 /* ...on a MVsensor module */
|
|
#define CONFIG_MVS_16BIT_FLASH /* ...with 16-bit flash access */
|
|
#define CONFIG_8xx_GCLK_FREQ 50000000/* ... and a 50 MHz CPU */
|
|
|
|
#define CONFIG_CLOCKS_IN_MHZ 1 /* clocks passsed to Linux in MHz */
|
|
|
|
#undef CONFIG_8xx_CONS_SMC1 /* Console is *NOT* on SMC1 */
|
|
#define CONFIG_8xx_CONS_SMC2 1 /* Console is on SMC2 */
|
|
#undef CONFIG_8xx_CONS_NONE
|
|
#define CONFIG_BAUDRATE 115200 /* console baudrate */
|
|
#define CONFIG_BOOTDELAY 5 /* autoboot after this many seconds */
|
|
|
|
#define CONFIG_PREBOOT "echo;" \
|
|
"echo To mount root over NFS use \"run bootnet\";" \
|
|
"echo To mount root from FLASH use \"run bootflash\";" \
|
|
"echo"
|
|
#define CONFIG_BOOTARGS "root=/dev/mtdblock2 rw"
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"bootp; " \
|
|
"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off; " \
|
|
"bootm"
|
|
|
|
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
|
|
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
|
|
|
|
#define CONFIG_WATCHDOG /* watchdog disabled/enabled */
|
|
|
|
#undef CONFIG_STATUS_LED /* Status LED disabled/enabled */
|
|
|
|
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
|
|
|
|
|
|
/*
|
|
* BOOTP options
|
|
*/
|
|
#define CONFIG_BOOTP_SUBNETMASK
|
|
#define CONFIG_BOOTP_GATEWAY
|
|
#define CONFIG_BOOTP_HOSTNAME
|
|
#define CONFIG_BOOTP_BOOTPATH
|
|
#define CONFIG_BOOTP_VENDOREX
|
|
|
|
#undef CONFIG_MAC_PARTITION
|
|
#undef CONFIG_DOS_PARTITION
|
|
|
|
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
|
|
|
|
|
|
/*
|
|
* Command line configuration.
|
|
*/
|
|
#define CONFIG_CMD_LOADS
|
|
#define CONFIG_CMD_LOADB
|
|
#define CONFIG_CMD_IMI
|
|
#define CONFIG_CMD_FLASH
|
|
#define CONFIG_CMD_MEMORY
|
|
#define CONFIG_CMD_NET
|
|
#define CONFIG_CMD_DHCP
|
|
#define CONFIG_CMD_SAVEENV
|
|
#define CONFIG_CMD_BOOTD
|
|
#define CONFIG_CMD_RUN
|
|
|
|
|
|
/*
|
|
* Miscellaneous configurable options
|
|
*/
|
|
#undef CONFIG_SYS_LONGHELP /* undef to save memory */
|
|
|
|
#undef CONFIG_SYS_HUSH_PARSER /* Hush parse for U-Boot ?? */
|
|
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
|
|
#else
|
|
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
|
|
#endif
|
|
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
|
|
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
|
|
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
|
|
|
|
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
|
|
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
|
|
|
|
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
|
|
|
|
/*
|
|
* Low Level Configuration Settings
|
|
* (address mappings, register initial values, etc.)
|
|
* You should know what you are doing if you make changes here.
|
|
*/
|
|
/*-----------------------------------------------------------------------
|
|
* Internal Memory Mapped Register
|
|
*/
|
|
#define CONFIG_SYS_IMMR 0xFFF00000
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Definitions for initial stack pointer and data area (in DPRAM)
|
|
*/
|
|
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
|
|
#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
|
|
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
|
|
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Start addresses for the final memory configuration
|
|
* (Set up by the startup code)
|
|
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
|
|
*/
|
|
#define CONFIG_SYS_SDRAM_BASE 0x00000000
|
|
#define CONFIG_SYS_FLASH_BASE 0x40000000
|
|
|
|
#define CONFIG_SYS_MONITOR_LEN (128 << 10) /* Reserve 192 kB for Monitor */
|
|
|
|
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
|
|
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
|
|
|
|
/*
|
|
* For booting Linux, the board info and command line data
|
|
* have to be in the first 8 MB of memory, since this is
|
|
* the maximum mapped by the Linux kernel during initialization.
|
|
*/
|
|
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* FLASH organization
|
|
*/
|
|
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
|
|
#define CONFIG_SYS_MAX_FLASH_SECT 71 /* max number of sectors on one chip (for AMD320DB chip) */
|
|
|
|
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
|
|
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
|
|
|
|
#define CONFIG_ENV_IS_IN_FLASH 1
|
|
|
|
/* 4MB flash - use bottom sectors of a bottom boot sector flash (16 bit access) */
|
|
#define CONFIG_ENV_OFFSET 0x8000 /* Offset of Environment Sector (bottom boot sector) */
|
|
#define CONFIG_ENV_SIZE 0x2000 /* Used Size of Environment Sector 8k */
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* Cache Configuration
|
|
*/
|
|
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
|
|
#if defined(CONFIG_CMD_KGDB)
|
|
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SYPCR - System Protection Control 11-9
|
|
* SYPCR can only be written once after reset!
|
|
*-----------------------------------------------------------------------
|
|
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
|
|
*/
|
|
#if defined(CONFIG_WATCHDOG)
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
|
|
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
|
|
#else
|
|
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
|
|
#endif
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SIUMCR - SIU Module Configuration 11-6
|
|
*-----------------------------------------------------------------------
|
|
* PCMCIA config., multi-function pin tri-state
|
|
*/
|
|
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* TBSCR - Time Base Status and Control 11-26
|
|
*-----------------------------------------------------------------------
|
|
* Clear Reference Interrupt Status, Timebase freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* RTCSC - Real-Time Clock Status and Control Register 11-27
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PISCR - Periodic Interrupt Status and Control 11-31
|
|
*-----------------------------------------------------------------------
|
|
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
|
|
*/
|
|
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
|
|
*-----------------------------------------------------------------------
|
|
* Reset PLL lock status sticky bit, timer expired status bit and timer
|
|
* interrupt status bit
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* SCCR - System Clock and reset Control Register 15-27
|
|
*-----------------------------------------------------------------------
|
|
* Set clock output, timebase and RTC source and divider,
|
|
* power management and some other internal clocks
|
|
*/
|
|
#define SCCR_MASK SCCR_EBDF11
|
|
#define CONFIG_SYS_SCCR (SCCR_TBS | \
|
|
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
|
|
SCCR_DFNL000 | SCCR_DFNH000 | SCCR_DFLCD000 | \
|
|
SCCR_DFALCD00)
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* PCMCIA stuff
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
|
|
#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
|
|
#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
|
|
#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
|
|
#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
|
|
#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
|
|
|
|
/*-----------------------------------------------------------------------
|
|
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
|
|
*-----------------------------------------------------------------------
|
|
*/
|
|
|
|
#define CONFIG_IDE_PCCARD 0 /* **DON'T** Use IDE with PC Card Adapter */
|
|
|
|
#undef CONFIG_IDE_PCMCIA /* Direct IDE not supported */
|
|
#undef CONFIG_IDE_LED /* LED for ide not supported */
|
|
#undef CONFIG_IDE_RESET /* reset for ide not supported */
|
|
|
|
#define CONFIG_SYS_IDE_MAXBUS 0 /* max. no. of IDE buses */
|
|
#define CONFIG_SYS_IDE_MAXDEVICE 0 /* max. no. of drives per IDE bus */
|
|
|
|
|
|
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
|
|
|
|
#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
|
|
|
|
/* Offset for data I/O */
|
|
#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
|
|
|
|
/* Offset for normal register accesses */
|
|
#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
|
|
|
|
/* Offset for alternate registers */
|
|
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
|
|
|
|
/*-----------------------------------------------------------------------
|
|
*
|
|
*-----------------------------------------------------------------------
|
|
*
|
|
*/
|
|
/*#define CONFIG_SYS_DER 0x2002000F*/
|
|
#define CONFIG_SYS_DER 0
|
|
|
|
/*
|
|
* Init Memory Controller:
|
|
*
|
|
* BR0/1 and OR0/1 (FLASH)
|
|
*/
|
|
|
|
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
|
|
#undef FLASH_BASE1_PRELIM
|
|
|
|
/* used to re-map FLASH both when starting from SRAM or FLASH:
|
|
* restrict access enough to keep SRAM working (if any)
|
|
* but not too much to meddle with FLASH accesses
|
|
*/
|
|
#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
|
|
#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
|
|
|
|
|
|
/*
|
|
* FLASH timing:
|
|
*/
|
|
/* 50 MHz CPU - 50 MHz bus: ACS = 00, TRLX = 1, CSNT = 1, SCY = 2, EHTR = 1 */
|
|
#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 | OR_TRLX | OR_CSNT_SAM | \
|
|
OR_SCY_2_CLK | OR_EHTR | OR_BI)
|
|
/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
|
|
/*
|
|
#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_ACS_DIV2 | OR_BI | \
|
|
OR_SCY_5_CLK | OR_EHTR)
|
|
*/
|
|
|
|
#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
|
|
#ifdef CONFIG_MVS_16BIT_FLASH
|
|
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_16 | BR_V )
|
|
#else
|
|
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_32 | BR_V )
|
|
#endif
|
|
|
|
#undef CONFIG_SYS_OR1_REMAP
|
|
#undef CONFIG_SYS_OR1_PRELIM
|
|
#undef CONFIG_SYS_BR1_PRELIM
|
|
/*
|
|
* BR2/3 and OR2/3 (SDRAM)
|
|
*
|
|
*/
|
|
#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
|
|
#undef SDRAM_BASE3_PRELIM
|
|
#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */
|
|
|
|
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
|
|
#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00
|
|
|
|
#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
|
|
#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
|
|
|
|
#undef CONFIG_SYS_OR3_PRELIM
|
|
#undef CONFIG_SYS_BR3_PRELIM
|
|
|
|
|
|
/*
|
|
* Memory Periodic Timer Prescaler
|
|
*
|
|
* The Divider for PTA (refresh timer) configuration is based on an
|
|
* example SDRAM configuration (64 MBit, one bank). The adjustment to
|
|
* the number of chip selects (NCS) and the actually needed refresh
|
|
* rate is done by setting MPTPR.
|
|
*
|
|
* PTA is calculated from
|
|
* PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
|
|
*
|
|
* gclk CPU clock (not bus clock!)
|
|
* Trefresh Refresh cycle * 4 (four word bursts used)
|
|
*
|
|
* 4096 Rows from SDRAM example configuration
|
|
* 1000 factor s -> ms
|
|
* 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
|
|
* 4 Number of refresh cycles per period
|
|
* 64 Refresh cycle in ms per number of rows
|
|
* --------------------------------------------
|
|
* Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
|
|
*
|
|
* 50 MHz => 50.000.000 / Divider = 98
|
|
* 66 Mhz => 66.000.000 / Divider = 129
|
|
* 80 Mhz => 80.000.000 / Divider = 156
|
|
*/
|
|
#define CONFIG_SYS_MAMR_PTA 98
|
|
|
|
/* refresh rate 15.6 us (= 64 ms / 4K = 62.4 / quad bursts) for <= 128 MBit */
|
|
#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
|
|
#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
|
|
|
|
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
|
|
#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
|
|
#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
|
|
|
|
/*
|
|
* MAMR settings for SDRAM
|
|
*/
|
|
|
|
/* 8 column SDRAM */
|
|
#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
|
|
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
|
|
/* 9 column SDRAM */
|
|
#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
|
|
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A7 | \
|
|
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
|
|
|
|
#endif /* __CONFIG_H */
|