u-boot/arch/powerpc/cpu/mpc85xx/ddr-gen1.c
York Sun c63e137014 powerpc/mpc8xxx: Add memory reset control
JEDEC spec requires the clocks to be stable before deasserting reset
signal for RDIMMs. Clocks start when any chip select is enabled and
clock control register is set. This patch also adds the interface to
toggle memory reset signal if needed by the boards.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09 12:41:39 -07:00

89 lines
2.4 KiB
C

/*
* Copyright 2008 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 as published by the Free Software Foundation.
*/
#include <common.h>
#include <asm/io.h>
#include <asm/fsl_ddr_sdram.h>
#if (CONFIG_CHIP_SELECTS_PER_CTRL > 4)
#error Invalid setting for CONFIG_CHIP_SELECTS_PER_CTRL
#endif
void fsl_ddr_set_memctl_regs(const fsl_ddr_cfg_regs_t *regs,
unsigned int ctrl_num, int step)
{
unsigned int i;
volatile ccsr_ddr_t *ddr = (void *)CONFIG_SYS_MPC8xxx_DDR_ADDR;
if (ctrl_num != 0) {
printf("%s unexpected ctrl_num = %u\n", __FUNCTION__, ctrl_num);
return;
}
for (i = 0; i < CONFIG_CHIP_SELECTS_PER_CTRL; i++) {
if (i == 0) {
out_be32(&ddr->cs0_bnds, regs->cs[i].bnds);
out_be32(&ddr->cs0_config, regs->cs[i].config);
} else if (i == 1) {
out_be32(&ddr->cs1_bnds, regs->cs[i].bnds);
out_be32(&ddr->cs1_config, regs->cs[i].config);
} else if (i == 2) {
out_be32(&ddr->cs2_bnds, regs->cs[i].bnds);
out_be32(&ddr->cs2_config, regs->cs[i].config);
} else if (i == 3) {
out_be32(&ddr->cs3_bnds, regs->cs[i].bnds);
out_be32(&ddr->cs3_config, regs->cs[i].config);
}
}
out_be32(&ddr->timing_cfg_1, regs->timing_cfg_1);
out_be32(&ddr->timing_cfg_2, regs->timing_cfg_2);
out_be32(&ddr->sdram_mode, regs->ddr_sdram_mode);
out_be32(&ddr->sdram_interval, regs->ddr_sdram_interval);
#if defined(CONFIG_MPC8555) || defined(CONFIG_MPC8541)
out_be32(&ddr->sdram_clk_cntl, regs->ddr_sdram_clk_cntl);
#endif
/*
* 200 painful micro-seconds must elapse between
* the DDR clock setup and the DDR config enable.
*/
udelay(200);
asm volatile("sync;isync");
out_be32(&ddr->sdram_cfg, regs->ddr_sdram_cfg);
asm("sync;isync;msync");
udelay(500);
}
#if defined(CONFIG_DDR_ECC) && !defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
/*
* Initialize all of memory for ECC, then enable errors.
*/
void
ddr_enable_ecc(unsigned int dram_size)
{
volatile ccsr_ddr_t *ddr= (void *)(CONFIG_SYS_MPC8xxx_DDR_ADDR);
dma_meminit(CONFIG_MEM_INIT_VALUE, dram_size);
/*
* Enable errors for ECC.
*/
debug("DMA DDR: err_disable = 0x%08x\n", ddr->err_disable);
ddr->err_disable = 0x00000000;
asm("sync;isync;msync");
debug("DMA DDR: err_disable = 0x%08x\n", ddr->err_disable);
}
#endif /* CONFIG_DDR_ECC && ! CONFIG_ECC_INIT_VIA_DDRCONTROLLER */