mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-05 11:00:15 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
208 lines
5.3 KiB
C
208 lines
5.3 KiB
C
/*
|
|
* (C) Copyright 2001-2003
|
|
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/processor.h>
|
|
#include <asm/io.h>
|
|
#include <command.h>
|
|
#include <malloc.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
extern void lxt971_no_sleep(void);
|
|
|
|
int board_revision(void)
|
|
{
|
|
unsigned long osrl_reg;
|
|
unsigned long isr1l_reg;
|
|
unsigned long tcr_reg;
|
|
unsigned long value;
|
|
|
|
/*
|
|
* Get version of HUB405 board from GPIO's
|
|
*/
|
|
|
|
/*
|
|
* Setup GPIO pin(s) (IRQ6/GPIO23)
|
|
*/
|
|
osrl_reg = in_be32((void *)GPIO0_OSRH);
|
|
isr1l_reg = in_be32((void *)GPIO0_ISR1H);
|
|
tcr_reg = in_be32((void *)GPIO0_TCR);
|
|
out_be32((void *)GPIO0_OSRH, osrl_reg & ~0x00030000); /* output select */
|
|
out_be32((void *)GPIO0_ISR1H, isr1l_reg | 0x00030000); /* input select */
|
|
out_be32((void *)GPIO0_TCR, tcr_reg & ~0x00000100); /* select input */
|
|
|
|
udelay(1000); /* wait some time before reading input */
|
|
value = in_be32((void *)GPIO0_IR) & 0x00000100; /* get config bits */
|
|
|
|
/*
|
|
* Restore GPIO settings
|
|
*/
|
|
out_be32((void *)GPIO0_OSRH, osrl_reg); /* output select */
|
|
out_be32((void *)GPIO0_ISR1H, isr1l_reg); /* input select */
|
|
out_be32((void *)GPIO0_TCR, tcr_reg); /* enable output driver for outputs */
|
|
|
|
if (value & 0x00000100) {
|
|
/* Revision 1.1 or 1.2 detected */
|
|
return 1;
|
|
}
|
|
|
|
/* Revision 1.0 */
|
|
return 0;
|
|
}
|
|
|
|
|
|
int board_early_init_f (void)
|
|
{
|
|
/*
|
|
* IRQ 0-15 405GP internally generated; active high; level sensitive
|
|
* IRQ 16 405GP internally generated; active low; level sensitive
|
|
* IRQ 17-24 RESERVED
|
|
* IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
|
|
* IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
|
|
* IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
|
|
* IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
|
|
* IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
|
|
* IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
|
|
* IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
|
|
*/
|
|
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
|
|
mtdcr(UIC0ER, 0x00000000); /* disable all ints */
|
|
mtdcr(UIC0CR, 0x00000000); /* set all to be non-critical*/
|
|
mtdcr(UIC0PR, 0xFFFFFF9F); /* set int polarities */
|
|
mtdcr(UIC0TR, 0x10000000); /* set int trigger levels */
|
|
mtdcr(UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority*/
|
|
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
|
|
|
|
/*
|
|
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
|
|
*/
|
|
mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
|
|
|
|
return 0;
|
|
}
|
|
|
|
#define LED_REG (DUART0_BA + 0x20)
|
|
int misc_init_r (void)
|
|
{
|
|
unsigned long val;
|
|
int delay, flashcnt;
|
|
char *str;
|
|
char hw_rev[4];
|
|
|
|
/*
|
|
* Enable interrupts in exar duart mcr[3]
|
|
*/
|
|
out_8((void *)(DUART0_BA + 4), 0x08);
|
|
out_8((void *)(DUART1_BA + 4), 0x08);
|
|
out_8((void *)(DUART2_BA + 4), 0x08);
|
|
out_8((void *)(DUART3_BA + 4), 0x08);
|
|
|
|
/*
|
|
* Set RS232/RS422 control (RS232 = high on GPIO)
|
|
*/
|
|
val = in_be32((void *)GPIO0_OR);
|
|
val &= ~(CONFIG_SYS_UART2_RS232 | CONFIG_SYS_UART3_RS232 |
|
|
CONFIG_SYS_UART4_RS232 | CONFIG_SYS_UART5_RS232);
|
|
|
|
str = getenv("phys0");
|
|
if (!str || (str && (str[0] == '0')))
|
|
val |= CONFIG_SYS_UART2_RS232;
|
|
|
|
str = getenv("phys1");
|
|
if (!str || (str && (str[0] == '0')))
|
|
val |= CONFIG_SYS_UART3_RS232;
|
|
|
|
str = getenv("phys2");
|
|
if (!str || (str && (str[0] == '0')))
|
|
val |= CONFIG_SYS_UART4_RS232;
|
|
|
|
str = getenv("phys3");
|
|
if (!str || (str && (str[0] == '0')))
|
|
val |= CONFIG_SYS_UART5_RS232;
|
|
|
|
out_be32((void *)GPIO0_OR, val);
|
|
|
|
/*
|
|
* check board type and setup AP power
|
|
*/
|
|
str = getenv("bd_type"); /* this is only set on non prototype hardware */
|
|
if (str != NULL) {
|
|
if ((strcmp(str, "swch405") == 0) || ((!strcmp(str, "hub405") && (gd->board_type >= 1)))) {
|
|
unsigned char led_reg_default = 0;
|
|
str = getenv("ap_pwr");
|
|
if (!str || (str && (str[0] == '1')))
|
|
led_reg_default = 0x04 | 0x02 ; /* U2_LED | AP_PWR */
|
|
|
|
/*
|
|
* Flash LEDs
|
|
*/
|
|
for (flashcnt = 0; flashcnt < 3; flashcnt++) {
|
|
/* LED_A..D off */
|
|
out_8((void *)LED_REG, led_reg_default);
|
|
for (delay = 0; delay < 100; delay++)
|
|
udelay(1000);
|
|
/* LED_A..D on */
|
|
out_8((void *)LED_REG, led_reg_default | 0xf0);
|
|
for (delay = 0; delay < 50; delay++)
|
|
udelay(1000);
|
|
}
|
|
out_8((void *)LED_REG, led_reg_default);
|
|
}
|
|
}
|
|
|
|
/*
|
|
* Reset external DUARTs
|
|
*/
|
|
out_be32((void *)GPIO0_OR,
|
|
in_be32((void *)GPIO0_OR) | CONFIG_SYS_DUART_RST); /* set reset to high */
|
|
udelay(10); /* wait 10us */
|
|
out_be32((void *)GPIO0_OR,
|
|
in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_DUART_RST); /* set reset to low */
|
|
udelay(1000); /* wait 1ms */
|
|
|
|
/*
|
|
* Store hardware revision in environment for further processing
|
|
*/
|
|
sprintf(hw_rev, "1.%ld", gd->board_type);
|
|
setenv("hw_rev", hw_rev);
|
|
return (0);
|
|
}
|
|
|
|
|
|
/*
|
|
* Check Board Identity:
|
|
*/
|
|
int checkboard (void)
|
|
{
|
|
char str[64];
|
|
int i = getenv_f("serial#", str, sizeof(str));
|
|
|
|
puts ("Board: ");
|
|
|
|
if (i == -1) {
|
|
puts ("### No HW ID - assuming HUB405");
|
|
} else {
|
|
puts(str);
|
|
}
|
|
|
|
if (getenv_f("bd_type", str, sizeof(str)) != -1) {
|
|
printf(" (%s", str);
|
|
} else {
|
|
puts(" (Missing bd_type!");
|
|
}
|
|
|
|
gd->board_type = board_revision();
|
|
printf(", Rev 1.%ld)\n", gd->board_type);
|
|
|
|
/*
|
|
* Disable sleep mode in LXT971
|
|
*/
|
|
lxt971_no_sleep();
|
|
|
|
return 0;
|
|
}
|