mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-07 20:03:12 +00:00
1a4596601f
Signed-off-by: Wolfgang Denk <wd@denx.de> [trini: Fixup common/cmd_io.c] Signed-off-by: Tom Rini <trini@ti.com>
475 lines
9.8 KiB
C
475 lines
9.8 KiB
C
/*
|
|
* (C) Copyright 2000
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*
|
|
* Hacked for the DB64360 board by Ingo.Assmus@keymile.com
|
|
* extra improvments by Brain Waite
|
|
* for cpci750 by reinhard.arlt@esd-electronics.com
|
|
*/
|
|
#include <common.h>
|
|
#include <mpc8xx.h>
|
|
#include <malloc.h>
|
|
#include <i2c.h>
|
|
#include "../../Marvell/include/mv_gen_reg.h"
|
|
#include "../../Marvell/include/core.h"
|
|
|
|
#define I2C_DELAY 100
|
|
#undef DEBUG_I2C
|
|
|
|
#ifdef DEBUG_I2C
|
|
#define DP(x) x
|
|
#else
|
|
#define DP(x)
|
|
#endif
|
|
|
|
/* Assuming that there is only one master on the bus (us) */
|
|
|
|
void i2c_init (int speed, int slaveaddr)
|
|
{
|
|
unsigned int n, m, freq, margin, power;
|
|
unsigned int actualN = 0, actualM = 0;
|
|
unsigned int minMargin = 0xffffffff;
|
|
unsigned int tclk = CONFIG_SYS_TCLK;
|
|
unsigned int i2cFreq = speed; /* 100000 max. Fast mode not supported */
|
|
|
|
DP (puts ("i2c_init\n"));
|
|
/* gtI2cMasterInit */
|
|
for (n = 0; n < 8; n++) {
|
|
for (m = 0; m < 16; m++) {
|
|
power = 2 << n; /* power = 2^(n+1) */
|
|
freq = tclk / (10 * (m + 1) * power);
|
|
if (i2cFreq > freq)
|
|
margin = i2cFreq - freq;
|
|
else
|
|
margin = freq - i2cFreq;
|
|
if (margin < minMargin) {
|
|
minMargin = margin;
|
|
actualN = n;
|
|
actualM = m;
|
|
}
|
|
}
|
|
}
|
|
|
|
DP (puts ("setup i2c bus\n"));
|
|
|
|
/* Setup bus */
|
|
/* gtI2cReset */
|
|
GT_REG_WRITE (I2C_SOFT_RESET, 0);
|
|
asm(" sync");
|
|
GT_REG_WRITE (I2C_CONTROL, 0);
|
|
asm(" sync");
|
|
|
|
DP (puts ("set baudrate\n"));
|
|
|
|
GT_REG_WRITE (I2C_STATUS_BAUDE_RATE, (actualM << 3) | actualN);
|
|
asm(" sync");
|
|
|
|
DP (puts ("udelay...\n"));
|
|
|
|
udelay (I2C_DELAY);
|
|
|
|
GT_REG_WRITE (I2C_CONTROL, (0x1 << 2) | (0x1 << 6));
|
|
asm(" sync");
|
|
}
|
|
|
|
|
|
static uchar i2c_select_device (uchar dev_addr, uchar read, int ten_bit)
|
|
{
|
|
unsigned int status, data, bits = 7;
|
|
unsigned int control;
|
|
int count = 0;
|
|
|
|
DP (puts ("i2c_select_device\n"));
|
|
|
|
/* Output slave address */
|
|
|
|
if (ten_bit) {
|
|
bits = 10;
|
|
}
|
|
|
|
GT_REG_READ (I2C_CONTROL, &control);
|
|
control |= (0x1 << 2);
|
|
GT_REG_WRITE (I2C_CONTROL, control);
|
|
asm(" sync");
|
|
|
|
GT_REG_READ (I2C_CONTROL, &control);
|
|
control |= (0x1 << 5); /* generate the I2C_START_BIT */
|
|
GT_REG_WRITE (I2C_CONTROL, control);
|
|
asm(" sync");
|
|
RESET_REG_BITS (I2C_CONTROL, (0x01 << 3));
|
|
asm(" sync");
|
|
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
while ((status & 0x08) != 0x08) {
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
}
|
|
|
|
|
|
count = 0;
|
|
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &status);
|
|
while (((status & 0xff) != 0x08) && ((status & 0xff) != 0x10)){
|
|
if (count > 200) {
|
|
#ifdef DEBUG_I2C
|
|
printf ("Failed to set startbit: 0x%02x\n", status);
|
|
#endif
|
|
GT_REG_WRITE (I2C_CONTROL, (0x1 << 4)); /*stop */
|
|
asm(" sync");
|
|
return (status);
|
|
}
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &status);
|
|
count++;
|
|
}
|
|
|
|
DP (puts ("i2c_select_device:write addr byte\n"));
|
|
|
|
/* assert the address */
|
|
|
|
data = (dev_addr << 1);
|
|
/* set the read bit */
|
|
data |= read;
|
|
GT_REG_WRITE (I2C_DATA, data);
|
|
asm(" sync");
|
|
RESET_REG_BITS (I2C_CONTROL, BIT3);
|
|
asm(" sync");
|
|
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
while ((status & 0x08) != 0x08) {
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
}
|
|
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &status);
|
|
count = 0;
|
|
while (((status & 0xff) != 0x40) && ((status & 0xff) != 0x18)) {
|
|
if (count > 200) {
|
|
#ifdef DEBUG_I2C
|
|
printf ("Failed to write address: 0x%02x\n", status);
|
|
#endif
|
|
GT_REG_WRITE (I2C_CONTROL, (0x1 << 4)); /*stop */
|
|
return (status);
|
|
}
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &status);
|
|
asm(" sync");
|
|
count++;
|
|
}
|
|
|
|
if (bits == 10) {
|
|
printf ("10 bit I2C addressing not yet implemented\n");
|
|
return (0xff);
|
|
}
|
|
|
|
return (0);
|
|
}
|
|
|
|
static uchar i2c_get_data (uchar * return_data, int len)
|
|
{
|
|
|
|
unsigned int data, status;
|
|
int count = 0;
|
|
|
|
DP (puts ("i2c_get_data\n"));
|
|
|
|
while (len) {
|
|
|
|
RESET_REG_BITS (I2C_CONTROL, BIT3);
|
|
asm(" sync");
|
|
|
|
/* Get and return the data */
|
|
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
while ((status & 0x08) != 0x08) {
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
}
|
|
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &status);
|
|
count++;
|
|
while ((status & 0xff) != 0x50) {
|
|
if (count > 20) {
|
|
#ifdef DEBUG_I2C
|
|
printf ("Failed to get data len status: 0x%02x\n", status);
|
|
#endif
|
|
GT_REG_WRITE (I2C_CONTROL, (0x1 << 4)); /*stop */
|
|
asm(" sync");
|
|
return 0;
|
|
}
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &status);
|
|
count++;
|
|
}
|
|
GT_REG_READ (I2C_DATA, &data);
|
|
len--;
|
|
*return_data = (uchar) data;
|
|
return_data++;
|
|
|
|
}
|
|
RESET_REG_BITS (I2C_CONTROL, BIT2 | BIT3);
|
|
asm(" sync");
|
|
count = 0;
|
|
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
while ((status & 0x08) != 0x08) {
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
}
|
|
|
|
while ((status & 0xff) != 0x58) {
|
|
if (count > 2000) {
|
|
GT_REG_WRITE (I2C_CONTROL, (0x1 << 4)); /*stop */
|
|
return (status);
|
|
}
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &status);
|
|
count++;
|
|
}
|
|
GT_REG_WRITE (I2C_CONTROL, (0x1 << 4)); /* stop */
|
|
asm(" sync");
|
|
RESET_REG_BITS (I2C_CONTROL, (0x1 << 3));
|
|
asm(" sync");
|
|
|
|
return (0);
|
|
}
|
|
|
|
|
|
static uchar i2c_write_data (unsigned int *data, int len)
|
|
{
|
|
unsigned int status;
|
|
int count;
|
|
unsigned int temp;
|
|
unsigned int *temp_ptr = data;
|
|
|
|
DP (puts ("i2c_write_data\n"));
|
|
|
|
while (len) {
|
|
count = 0;
|
|
temp = (unsigned int) (*temp_ptr);
|
|
GT_REG_WRITE (I2C_DATA, temp);
|
|
asm(" sync");
|
|
RESET_REG_BITS (I2C_CONTROL, (0x1 << 3));
|
|
asm(" sync");
|
|
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
while ((status & 0x08) != 0x08) {
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
}
|
|
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &status);
|
|
count++;
|
|
while ((status & 0xff) != 0x28) {
|
|
if (count > 200) {
|
|
GT_REG_WRITE (I2C_CONTROL, (0x1 << 4)); /*stop */
|
|
asm(" sync");
|
|
return (status);
|
|
}
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &status);
|
|
count++;
|
|
}
|
|
len--;
|
|
temp_ptr++;
|
|
}
|
|
return (0);
|
|
}
|
|
|
|
|
|
static uchar i2c_write_byte (unsigned char *data, int len)
|
|
{
|
|
unsigned int status;
|
|
int count;
|
|
unsigned int temp;
|
|
unsigned char *temp_ptr = data;
|
|
|
|
DP (puts ("i2c_write_byte\n"));
|
|
|
|
while (len) {
|
|
count = 0;
|
|
/* Set and assert the data */
|
|
temp = *temp_ptr;
|
|
GT_REG_WRITE (I2C_DATA, temp);
|
|
asm(" sync");
|
|
RESET_REG_BITS (I2C_CONTROL, (0x1 << 3));
|
|
asm(" sync");
|
|
|
|
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
while ((status & 0x08) != 0x08) {
|
|
GT_REG_READ (I2C_CONTROL, &status);
|
|
}
|
|
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &status);
|
|
count++;
|
|
while ((status & 0xff) != 0x28) {
|
|
if (count > 200) {
|
|
GT_REG_WRITE (I2C_CONTROL, (0x1 << 4)); /*stop */
|
|
asm(" sync");
|
|
return (status);
|
|
}
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &status);
|
|
count++;
|
|
}
|
|
len--;
|
|
temp_ptr++;
|
|
}
|
|
return (0);
|
|
}
|
|
|
|
static uchar
|
|
i2c_set_dev_offset (uchar dev_addr, unsigned int offset, int ten_bit,
|
|
int alen)
|
|
{
|
|
uchar status;
|
|
unsigned int table[2];
|
|
|
|
table[1] = (offset ) & 0x0ff; /* low byte */
|
|
table[0] = (offset >> 8) & 0x0ff; /* high byte */
|
|
|
|
DP (puts ("i2c_set_dev_offset\n"));
|
|
|
|
status = i2c_select_device (dev_addr, 0, ten_bit);
|
|
if (status) {
|
|
#ifdef DEBUG_I2C
|
|
22 printf ("Failed to select device setting offset: 0x%02x\n",
|
|
status);
|
|
#endif
|
|
return status;
|
|
}
|
|
/* check the address offset length */
|
|
if (alen == 0)
|
|
/* no address offset */
|
|
return (0);
|
|
else if (alen == 1) {
|
|
/* 1 byte address offset */
|
|
status = i2c_write_data (&offset, 1);
|
|
if (status) {
|
|
#ifdef DEBUG_I2C
|
|
printf ("Failed to write data: 0x%02x\n", status);
|
|
#endif
|
|
return status;
|
|
}
|
|
} else if (alen == 2) {
|
|
/* 2 bytes address offset */
|
|
status = i2c_write_data (table, 2);
|
|
if (status) {
|
|
#ifdef DEBUG_I2C
|
|
printf ("Failed to write data: 0x%02x\n", status);
|
|
#endif
|
|
return status;
|
|
}
|
|
} else {
|
|
/* address offset unknown or not supported */
|
|
printf ("Address length offset %d is not supported\n", alen);
|
|
return 1;
|
|
}
|
|
return 0; /* sucessful completion */
|
|
}
|
|
|
|
int
|
|
i2c_read (uchar dev_addr, unsigned int offset, int alen, uchar * data,
|
|
int len)
|
|
{
|
|
uchar status = 0;
|
|
unsigned int i2cFreq = CONFIG_SYS_I2C_SPEED;
|
|
|
|
DP (puts ("i2c_read\n"));
|
|
|
|
/* set the i2c frequency */
|
|
i2c_init (i2cFreq, CONFIG_SYS_I2C_SLAVE);
|
|
|
|
status = i2c_set_dev_offset (dev_addr, offset, 0, alen); /* send the slave address + offset */
|
|
if (status) {
|
|
#ifdef DEBUG_I2C
|
|
printf ("Failed to set slave address & offset: 0x%02x\n",
|
|
status);
|
|
#endif
|
|
return status;
|
|
}
|
|
|
|
status = i2c_select_device (dev_addr, 1, 0);
|
|
if (status) {
|
|
#ifdef DEBUG_I2C
|
|
printf ("Failed to select device for data read: 0x%02x\n",
|
|
status);
|
|
#endif
|
|
return status;
|
|
}
|
|
|
|
status = i2c_get_data (data, len);
|
|
if (status) {
|
|
#ifdef DEBUG_I2C
|
|
printf ("Data not read: 0x%02x\n", status);
|
|
#endif
|
|
return status;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
|
|
void i2c_stop (void)
|
|
{
|
|
GT_REG_WRITE (I2C_CONTROL, (0x1 << 4));
|
|
asm(" sync");
|
|
}
|
|
|
|
|
|
int
|
|
i2c_write (uchar dev_addr, unsigned int offset, int alen, uchar * data,
|
|
int len)
|
|
{
|
|
uchar status = 0;
|
|
unsigned int i2cFreq = CONFIG_SYS_I2C_SPEED;
|
|
|
|
DP (puts ("i2c_write\n"));
|
|
|
|
/* set the i2c frequency */
|
|
i2c_init (i2cFreq, CONFIG_SYS_I2C_SLAVE);
|
|
|
|
status = i2c_set_dev_offset (dev_addr, offset, 0, alen); /* send the slave address + offset */
|
|
if (status) {
|
|
#ifdef DEBUG_I2C
|
|
printf ("Failed to set slave address & offset: 0x%02x\n",
|
|
status);
|
|
#endif
|
|
return status;
|
|
}
|
|
|
|
|
|
status = i2c_write_byte (data, len); /* write the data */
|
|
if (status) {
|
|
#ifdef DEBUG_I2C
|
|
printf ("Data not written: 0x%02x\n", status);
|
|
#endif
|
|
return status;
|
|
}
|
|
/* issue a stop bit */
|
|
i2c_stop ();
|
|
return 0;
|
|
}
|
|
|
|
|
|
int i2c_probe (uchar chip)
|
|
{
|
|
|
|
#ifdef DEBUG_I2C
|
|
unsigned int i2c_status;
|
|
#endif
|
|
uchar status = 0;
|
|
unsigned int i2cFreq = CONFIG_SYS_I2C_SPEED;
|
|
|
|
DP (puts ("i2c_probe\n"));
|
|
|
|
/* set the i2c frequency */
|
|
i2c_init (i2cFreq, CONFIG_SYS_I2C_SLAVE);
|
|
|
|
status = i2c_set_dev_offset (chip, 0, 0, 0); /* send the slave address + no offset */
|
|
if (status) {
|
|
#ifdef DEBUG_I2C
|
|
printf ("Failed to set slave address: 0x%02x\n", status);
|
|
#endif
|
|
return (int) status;
|
|
}
|
|
#ifdef DEBUG_I2C
|
|
GT_REG_READ (I2C_STATUS_BAUDE_RATE, &i2c_status);
|
|
printf ("address %#x returned %#x\n", chip, i2c_status);
|
|
#endif
|
|
/* issue a stop bit */
|
|
i2c_stop ();
|
|
return 0; /* successful completion */
|
|
}
|