u-boot/arch/arm/mach-k3/am6_init.c
Lokesh Vutla dc57a554a5 arm: mach-k3: sysfw-loader: Add support for rom loading sysfw image
Starting J7200 SoC, ROM supports for loading sysfw directly from boot
image. In such cases, SPL need not load sysfw from boot media, but need
to receive boot notification message from sysfw. So separate out
remoteproc calls for system controller from sysfw loader and just
receive the boot notification if sysfw is already loaded.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Suman Anna <s-anna@ti.com>
2020-08-11 20:34:46 +05:30

396 lines
10 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* AM6: SoC specific initialization
*
* Copyright (C) 2017-2018 Texas Instruments Incorporated - http://www.ti.com/
* Lokesh Vutla <lokeshvutla@ti.com>
*/
#include <common.h>
#include <fdt_support.h>
#include <init.h>
#include <asm/io.h>
#include <spl.h>
#include <asm/arch/hardware.h>
#include <asm/arch/sysfw-loader.h>
#include <asm/arch/sys_proto.h>
#include "common.h"
#include <dm.h>
#include <dm/uclass-internal.h>
#include <dm/pinctrl.h>
#include <linux/soc/ti/ti_sci_protocol.h>
#include <log.h>
#include <mmc.h>
#include <stdlib.h>
DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_SPL_BUILD
#ifdef CONFIG_K3_LOAD_SYSFW
#ifdef CONFIG_TI_SECURE_DEVICE
struct fwl_data main_cbass_fwls[] = {
{ "MMCSD1_CFG", 2057, 1 },
{ "MMCSD0_CFG", 2058, 1 },
{ "USB3SS0_SLV0", 2176, 2 },
{ "PCIE0_SLV", 2336, 8 },
{ "PCIE1_SLV", 2337, 8 },
{ "PCIE0_CFG", 2688, 1 },
{ "PCIE1_CFG", 2689, 1 },
}, mcu_cbass_fwls[] = {
{ "MCU_ARMSS0_CORE0_SLV", 1024, 1 },
{ "MCU_ARMSS0_CORE1_SLV", 1028, 1 },
{ "MCU_FSS0_S1", 1033, 8 },
{ "MCU_FSS0_S0", 1036, 8 },
{ "MCU_CPSW0", 1220, 1 },
};
#endif
#endif
static void ctrl_mmr_unlock(void)
{
/* Unlock all WKUP_CTRL_MMR0 module registers */
mmr_unlock(WKUP_CTRL_MMR0_BASE, 0);
mmr_unlock(WKUP_CTRL_MMR0_BASE, 1);
mmr_unlock(WKUP_CTRL_MMR0_BASE, 2);
mmr_unlock(WKUP_CTRL_MMR0_BASE, 3);
mmr_unlock(WKUP_CTRL_MMR0_BASE, 6);
mmr_unlock(WKUP_CTRL_MMR0_BASE, 7);
/* Unlock all MCU_CTRL_MMR0 module registers */
mmr_unlock(MCU_CTRL_MMR0_BASE, 0);
mmr_unlock(MCU_CTRL_MMR0_BASE, 1);
mmr_unlock(MCU_CTRL_MMR0_BASE, 2);
mmr_unlock(MCU_CTRL_MMR0_BASE, 6);
/* Unlock all CTRL_MMR0 module registers */
mmr_unlock(CTRL_MMR0_BASE, 0);
mmr_unlock(CTRL_MMR0_BASE, 1);
mmr_unlock(CTRL_MMR0_BASE, 2);
mmr_unlock(CTRL_MMR0_BASE, 3);
mmr_unlock(CTRL_MMR0_BASE, 6);
mmr_unlock(CTRL_MMR0_BASE, 7);
}
/*
* This uninitialized global variable would normal end up in the .bss section,
* but the .bss is cleared between writing and reading this variable, so move
* it to the .data section.
*/
u32 bootindex __attribute__((section(".data")));
static void store_boot_index_from_rom(void)
{
bootindex = *(u32 *)(CONFIG_SYS_K3_BOOT_PARAM_TABLE_INDEX);
}
#if defined(CONFIG_K3_LOAD_SYSFW) && CONFIG_IS_ENABLED(DM_MMC)
void k3_mmc_stop_clock(void)
{
if (spl_boot_device() == BOOT_DEVICE_MMC1) {
struct mmc *mmc = find_mmc_device(0);
if (!mmc)
return;
mmc->saved_clock = mmc->clock;
mmc_set_clock(mmc, 0, true);
}
}
void k3_mmc_restart_clock(void)
{
if (spl_boot_device() == BOOT_DEVICE_MMC1) {
struct mmc *mmc = find_mmc_device(0);
if (!mmc)
return;
mmc_set_clock(mmc, mmc->saved_clock, false);
}
}
#else
void k3_mmc_stop_clock(void) {}
void k3_mmc_restart_clock(void) {}
#endif
#if CONFIG_IS_ENABLED(DFU) || CONFIG_IS_ENABLED(USB_STORAGE)
#define CTRLMMR_SERDES0_CTRL 0x00104080
#define PCIE_LANE0 0x1
static int fixup_usb_boot(void)
{
int ret;
switch (spl_boot_device()) {
case BOOT_DEVICE_USB:
/*
* If bootmode is Host bootmode, fixup the dr_mode to host
* before the dwc3 bind takes place
*/
ret = fdt_find_and_setprop((void *)gd->fdt_blob,
"/interconnect@100000/dwc3@4000000/usb@10000",
"dr_mode", "host", 11, 0);
if (ret)
printf("%s: fdt_find_and_setprop() failed:%d\n", __func__,
ret);
fallthrough;
case BOOT_DEVICE_DFU:
/*
* The serdes mux between PCIe and USB3 needs to be set to PCIe for
* accessing the interface at USB 2.0
*/
writel(PCIE_LANE0, CTRLMMR_SERDES0_CTRL);
default:
break;
}
return 0;
}
int fdtdec_board_setup(const void *fdt_blob)
{
return fixup_usb_boot();
}
#endif
void board_init_f(ulong dummy)
{
#if defined(CONFIG_K3_LOAD_SYSFW) || defined(CONFIG_K3_AM654_DDRSS)
struct udevice *dev;
size_t pool_size;
void *pool_addr;
int ret;
#endif
/*
* Cannot delay this further as there is a chance that
* K3_BOOT_PARAM_TABLE_INDEX can be over written by SPL MALLOC section.
*/
store_boot_index_from_rom();
/* Make all control module registers accessible */
ctrl_mmr_unlock();
#ifdef CONFIG_CPU_V7R
disable_linefill_optimization();
setup_k3_mpu_regions();
#endif
/* Init DM early in-order to invoke system controller */
spl_early_init();
#ifdef CONFIG_K3_EARLY_CONS
/*
* Allow establishing an early console as required for example when
* doing a UART-based boot. Note that this console may not "survive"
* through a SYSFW PM-init step and will need a re-init in some way
* due to changing module clock frequencies.
*/
early_console_init();
#endif
#ifdef CONFIG_K3_LOAD_SYSFW
/*
* Initialize an early full malloc environment. Do so by allocating a
* new malloc area inside the currently active pre-relocation "first"
* malloc pool of which we use all that's left.
*/
pool_size = CONFIG_VAL(SYS_MALLOC_F_LEN) - gd->malloc_ptr;
pool_addr = malloc(pool_size);
if (!pool_addr)
panic("ERROR: Can't allocate full malloc pool!\n");
mem_malloc_init((ulong)pool_addr, (ulong)pool_size);
gd->flags |= GD_FLG_FULL_MALLOC_INIT;
debug("%s: initialized an early full malloc pool at 0x%08lx of 0x%lx bytes\n",
__func__, (unsigned long)pool_addr, (unsigned long)pool_size);
/*
* Process pinctrl for the serial0 a.k.a. WKUP_UART0 module and continue
* regardless of the result of pinctrl. Do this without probing the
* device, but instead by searching the device that would request the
* given sequence number if probed. The UART will be used by the system
* firmware (SYSFW) image for various purposes and SYSFW depends on us
* to initialize its pin settings.
*/
ret = uclass_find_device_by_seq(UCLASS_SERIAL, 0, true, &dev);
if (!ret)
pinctrl_select_state(dev, "default");
/*
* Load, start up, and configure system controller firmware while
* also populating the SYSFW post-PM configuration callback hook.
*/
k3_sysfw_loader(false, k3_mmc_stop_clock, k3_mmc_restart_clock);
/* Prepare console output */
preloader_console_init();
/* Disable ROM configured firewalls right after loading sysfw */
#ifdef CONFIG_TI_SECURE_DEVICE
remove_fwl_configs(main_cbass_fwls, ARRAY_SIZE(main_cbass_fwls));
remove_fwl_configs(mcu_cbass_fwls, ARRAY_SIZE(mcu_cbass_fwls));
#endif
#else
/* Prepare console output */
preloader_console_init();
#endif
/* Output System Firmware version info */
k3_sysfw_print_ver();
/* Perform EEPROM-based board detection */
do_board_detect();
#if defined(CONFIG_CPU_V7R) && defined(CONFIG_K3_AVS0)
ret = uclass_get_device_by_driver(UCLASS_MISC, DM_GET_DRIVER(k3_avs),
&dev);
if (ret)
printf("AVS init failed: %d\n", ret);
#endif
#ifdef CONFIG_K3_AM654_DDRSS
ret = uclass_get_device(UCLASS_RAM, 0, &dev);
if (ret)
panic("DRAM init failed: %d\n", ret);
#endif
spl_enable_dcache();
}
u32 spl_mmc_boot_mode(const u32 boot_device)
{
#if defined(CONFIG_SUPPORT_EMMC_BOOT)
u32 devstat = readl(CTRLMMR_MAIN_DEVSTAT);
u32 bootmode = (devstat & CTRLMMR_MAIN_DEVSTAT_BOOTMODE_MASK) >>
CTRLMMR_MAIN_DEVSTAT_BOOTMODE_SHIFT;
/* eMMC boot0 mode is only supported for primary boot */
if (bootindex == K3_PRIMARY_BOOTMODE &&
bootmode == BOOT_DEVICE_MMC1)
return MMCSD_MODE_EMMCBOOT;
#endif
/* Everything else use filesystem if available */
#if defined(CONFIG_SPL_FS_FAT) || defined(CONFIG_SPL_FS_EXT4)
return MMCSD_MODE_FS;
#else
return MMCSD_MODE_RAW;
#endif
}
static u32 __get_backup_bootmedia(u32 devstat)
{
u32 bkup_boot = (devstat & CTRLMMR_MAIN_DEVSTAT_BKUP_BOOTMODE_MASK) >>
CTRLMMR_MAIN_DEVSTAT_BKUP_BOOTMODE_SHIFT;
switch (bkup_boot) {
case BACKUP_BOOT_DEVICE_USB:
return BOOT_DEVICE_USB;
case BACKUP_BOOT_DEVICE_UART:
return BOOT_DEVICE_UART;
case BACKUP_BOOT_DEVICE_ETHERNET:
return BOOT_DEVICE_ETHERNET;
case BACKUP_BOOT_DEVICE_MMC2:
{
u32 port = (devstat & CTRLMMR_MAIN_DEVSTAT_BKUP_MMC_PORT_MASK) >>
CTRLMMR_MAIN_DEVSTAT_BKUP_MMC_PORT_SHIFT;
if (port == 0x0)
return BOOT_DEVICE_MMC1;
return BOOT_DEVICE_MMC2;
}
case BACKUP_BOOT_DEVICE_SPI:
return BOOT_DEVICE_SPI;
case BACKUP_BOOT_DEVICE_HYPERFLASH:
return BOOT_DEVICE_HYPERFLASH;
case BACKUP_BOOT_DEVICE_I2C:
return BOOT_DEVICE_I2C;
};
return BOOT_DEVICE_RAM;
}
static u32 __get_primary_bootmedia(u32 devstat)
{
u32 bootmode = (devstat & CTRLMMR_MAIN_DEVSTAT_BOOTMODE_MASK) >>
CTRLMMR_MAIN_DEVSTAT_BOOTMODE_SHIFT;
if (bootmode == BOOT_DEVICE_OSPI || bootmode == BOOT_DEVICE_QSPI)
bootmode = BOOT_DEVICE_SPI;
if (bootmode == BOOT_DEVICE_MMC2) {
u32 port = (devstat & CTRLMMR_MAIN_DEVSTAT_MMC_PORT_MASK) >>
CTRLMMR_MAIN_DEVSTAT_MMC_PORT_SHIFT;
if (port == 0x0)
bootmode = BOOT_DEVICE_MMC1;
} else if (bootmode == BOOT_DEVICE_MMC1) {
u32 port = (devstat & CTRLMMR_MAIN_DEVSTAT_EMMC_PORT_MASK) >>
CTRLMMR_MAIN_DEVSTAT_EMMC_PORT_SHIFT;
if (port == 0x1)
bootmode = BOOT_DEVICE_MMC2;
} else if (bootmode == BOOT_DEVICE_DFU) {
u32 mode = (devstat & CTRLMMR_MAIN_DEVSTAT_USB_MODE_MASK) >>
CTRLMMR_MAIN_DEVSTAT_USB_MODE_SHIFT;
if (mode == 0x2)
bootmode = BOOT_DEVICE_USB;
}
return bootmode;
}
u32 spl_boot_device(void)
{
u32 devstat = readl(CTRLMMR_MAIN_DEVSTAT);
if (bootindex == K3_PRIMARY_BOOTMODE)
return __get_primary_bootmedia(devstat);
else
return __get_backup_bootmedia(devstat);
}
#endif
#ifdef CONFIG_SYS_K3_SPL_ATF
#define AM6_DEV_MCU_RTI0 134
#define AM6_DEV_MCU_RTI1 135
#define AM6_DEV_MCU_ARMSS0_CPU0 159
#define AM6_DEV_MCU_ARMSS0_CPU1 245
void release_resources_for_core_shutdown(void)
{
struct ti_sci_handle *ti_sci = get_ti_sci_handle();
struct ti_sci_dev_ops *dev_ops = &ti_sci->ops.dev_ops;
struct ti_sci_proc_ops *proc_ops = &ti_sci->ops.proc_ops;
int ret;
u32 i;
const u32 put_device_ids[] = {
AM6_DEV_MCU_RTI0,
AM6_DEV_MCU_RTI1,
};
/* Iterate through list of devices to put (shutdown) */
for (i = 0; i < ARRAY_SIZE(put_device_ids); i++) {
u32 id = put_device_ids[i];
ret = dev_ops->put_device(ti_sci, id);
if (ret)
panic("Failed to put device %u (%d)\n", id, ret);
}
const u32 put_core_ids[] = {
AM6_DEV_MCU_ARMSS0_CPU1,
AM6_DEV_MCU_ARMSS0_CPU0, /* Handle CPU0 after CPU1 */
};
/* Iterate through list of cores to put (shutdown) */
for (i = 0; i < ARRAY_SIZE(put_core_ids); i++) {
u32 id = put_core_ids[i];
/*
* Queue up the core shutdown request. Note that this call
* needs to be followed up by an actual invocation of an WFE
* or WFI CPU instruction.
*/
ret = proc_ops->proc_shutdown_no_wait(ti_sci, id);
if (ret)
panic("Failed sending core %u shutdown message (%d)\n",
id, ret);
}
}
#endif