u-boot/include/configs/theadorable.h
Tom Rini a09fea1d28 env: Finish migration of common ENV options
- In ARMv8 NXP Layerscape platforms we also need to make use of
  CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so.
- On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define
  to 0.
- Add Kconfig entry for ENV_ADDR.
- Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it.
- Add ENV_xxx_REDUND options that depend on their primary option and
  SYS_REDUNDAND_ENVIRONMENT
- On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR
  for the pre-main-U-Boot environment location.
- On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but
  rather it being non-zero, as it will now be zero by default.
- Rework the env_offset absolute in env/embedded.o to not use
  CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within
  ENV_IS_IN_FLASH.
- Migrate all platforms.

Cc: Wolfgang Denk <wd@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: uboot-stm32@st-md-mailman.stormreply.com
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
2019-11-20 18:32:09 -05:00

111 lines
2.8 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2015-2016 Stefan Roese <sr@denx.de>
*/
#ifndef _CONFIG_THEADORABLE_H
#define _CONFIG_THEADORABLE_H
/*
* High Level Configuration Options (easy to change)
*/
/*
* TEXT_BASE needs to be below 16MiB, since this area is scrubbed
* for DDR ECC byte filling in the SPL before loading the main
* U-Boot into it.
*/
#define CONFIG_SYS_TCLK 250000000 /* 250MHz */
/*
* Commands configuration
*/
/*
* The debugging version enables USB support via defconfig.
* This version should also enable all other non-production
* interfaces / features.
*/
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MVTWSI
#define CONFIG_I2C_MVTWSI_BASE0 MVEBU_TWSI_BASE
#define CONFIG_I2C_MVTWSI_BASE1 MVEBU_TWSI1_BASE
#define CONFIG_SYS_I2C_SLAVE 0x0
#define CONFIG_SYS_I2C_SPEED 100000
/* USB/EHCI configuration */
#define CONFIG_EHCI_IS_TDI
#define CONFIG_USB_MAX_CONTROLLER_COUNT 3
/* Environment in SPI NOR flash */
#define CONFIG_ENV_OVERWRITE
#define PHY_ANEG_TIMEOUT 8000 /* PHY needs a longer aneg time */
/* Keep device tree and initrd in lower memory so the kernel can access them */
#define CONFIG_EXTRA_ENV_SETTINGS \
"fdt_high=0x10000000\0" \
"initrd_high=0x10000000\0"
/* SATA support */
#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_LBA48
/* Enable LCD and reserve 512KB from top of memory*/
#define CONFIG_SYS_MEM_TOP_HIDE 0x80000
#define CONFIG_BMP_16BPP
#define CONFIG_BMP_24BPP
#define CONFIG_BMP_32BPP
/* FPGA programming support */
#define CONFIG_FPGA_STRATIX_V
/*
* Bootcounter
*/
/* Max size of RAM minus BOOTCOUNT_ADDR is the bootcounter address */
#define BOOTCOUNT_ADDR 0x1000
/*
* mv-common.h should be defined after CMD configs since it used them
* to enable certain macros
*/
#include "mv-common.h"
/*
* Memory layout while starting into the bin_hdr via the
* BootROM:
*
* 0x4000.4000 - 0x4003.4000 headers space (192KiB)
* 0x4000.4030 bin_hdr start address
* 0x4003.4000 - 0x4004.7c00 BootROM memory allocations (15KiB)
* 0x4007.fffc BootROM stack top
*
* The address space between 0x4007.fffc and 0x400f.fff is not locked in
* L2 cache thus cannot be used.
*/
/* SPL */
/* Defines for SPL */
#define CONFIG_SPL_MAX_SIZE ((128 << 10) - 0x4030)
#define CONFIG_SPL_BSS_START_ADDR (0x40000000 + (128 << 10))
#define CONFIG_SPL_BSS_MAX_SIZE (16 << 10)
#ifdef CONFIG_SPL_BUILD
#define CONFIG_SYS_MALLOC_SIMPLE
#endif
#define CONFIG_SPL_STACK (0x40000000 + ((192 - 16) << 10))
#define CONFIG_SPL_BOOTROM_SAVE (CONFIG_SPL_STACK + 4)
/* SPL related SPI defines */
#define CONFIG_SYS_U_BOOT_OFFS CONFIG_SYS_SPI_U_BOOT_OFFS
/* Enable DDR support in SPL (DDR3 training from Marvell bin_hdr) */
#define CONFIG_DDR_FIXED_SIZE (2 << 20) /* 2GiB */
#endif /* _CONFIG_THEADORABLE_H */