u-boot/include/configs/omap3_logic.h
Adam Ford bdaf24f8a5 ti_omap3_common: Add CONFIG_SYS_NS16550_COMx entries
Several boards do not use the default UART3, so they do a check
for ifdef CONFIG_SPL_BUILD and enable the pointer for
CONFIG_SYS_NS16550_COMx to point to OMAP34XX_UARTx.

Let's consoldate this all into one place, and remove them from the
individual boards.

Signed-off-by: Adam Ford <aford173@gmail.com>
2018-08-03 19:53:54 -04:00

209 lines
6.4 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2011 Logic Product Development <www.logicpd.com>
* Peter Barada <peter.barada@logicpd.com>
*
* Configuration settings for the Logic OMAP35x/DM37x SOM LV/Torpedo
* reference boards.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
#include <configs/ti_omap3_common.h>
/*
* We are only ever GP parts and will utilize all of the "downloaded image"
* area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in
* order to allow for BCH8 to fit in.
*/
#undef CONFIG_SPL_TEXT_BASE
#define CONFIG_SPL_TEXT_BASE 0x40200000
#define CONFIG_MISC_INIT_R /* misc_init_r dumps the die id */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
/* Hardware drivers */
/* I2C */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */
/* Board NAND Info. */
#ifdef CONFIG_NAND
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
/* NAND devices */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \
13, 14, 16, 17, 18, 19, 20, 21, 22, \
23, 24, 25, 26, 27, 28, 30, 31, 32, \
33, 34, 35, 36, 37, 38, 39, 40, 41, \
42, 44, 45, 46, 47, 48, 49, 50, 51, \
52, 53, 54, 55, 56}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 13
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
#endif
/* Environment information */
#define CONFIG_PREBOOT \
"setenv preboot;" \
"saveenv;"
#define CONFIG_EXTRA_ENV_SETTINGS \
DEFAULT_LINUX_BOOT_ENV \
"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext4 rootwait\0" \
"nandroot=ubi0:rootfs rw ubi.mtd=fs noinitrd\0" \
"nandrootfstype=ubifs rootwait\0" \
"autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"run defaultboot;" \
"fi; " \
"else run defaultboot; fi\0" \
"defaultboot=run mmcramboot\0" \
"consoledevice=ttyS0\0" \
"setconsole=setenv console ${consoledevice},${baudrate}n8\0" \
"dump_bootargs=echo 'Bootargs: '; echo $bootargs\0" \
"rotation=0\0" \
"vrfb_arg=if itest ${rotation} -ne 0; then " \
"setenv bootargs ${bootargs} omapfb.vrfb=y " \
"omapfb.rotate=${rotation}; " \
"fi\0" \
"optargs=ignore_loglevel early_printk no_console_suspend\0" \
"common_bootargs=run setconsole; setenv bootargs " \
"${bootargs} "\
"console=${console} " \
"${mtdparts} "\
"${optargs}; " \
"run vrfb_arg\0" \
"loadbootscript=load mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo 'Running bootscript from mmc ...'; " \
"source ${loadaddr}\0" \
"loadimage=mmc rescan; " \
"load mmc ${mmcdev} ${loadaddr} ${bootfile}\0" \
"ramdisksize=64000\0" \
"ramdiskimage=rootfs.ext2.gz.uboot\0" \
"loadramdisk=mmc rescan; " \
"load mmc ${mmcdev} ${rdaddr} ${ramdiskimage}\0" \
"ramargs=setenv bootargs "\
"root=/dev/ram rw ramdisk_size=${ramdisksize}\0" \
"mmcargs=setenv bootargs "\
"root=${mmcroot} rootfstype=${mmcrootfstype}\0" \
"nandargs=setenv bootargs "\
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
"nfsargs=setenv serverip ${tftpserver}; " \
"setenv bootargs root=/dev/nfs " \
"nfsroot=${nfsrootpath} " \
"ip=${ipaddr}:${tftpserver}:${gatewayip}:${netmask}::eth0:off\0" \
"nfsrootpath=/opt/nfs-exports/omap\0" \
"autoload=no\0" \
"loadfdt=mmc rescan; " \
"load mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
"mmcbootcommon=echo Booting with DT from mmc${mmcdev} ...; " \
"run mmcargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
"run loadimage; " \
"run loadfdt;\0 " \
"mmcbootz=setenv bootfile zImage; " \
"run mmcbootcommon; "\
"bootz ${loadaddr} - ${fdtaddr}\0" \
"mmcboot=setenv bootfile uImage; "\
"run mmcbootcommon; "\
"bootm ${loadaddr} - ${fdtaddr}\0" \
"mmcrambootcommon=echo 'Booting kernel from MMC w/ramdisk...'; " \
"run ramargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
"run loadimage; " \
"run loadfdt; " \
"run loadramdisk\0" \
"mmcramboot=setenv bootfile uImage; " \
"run mmcrambootcommon; " \
"bootm ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
"mmcrambootz=setenv bootfile zImage; " \
"run mmcrambootcommon; " \
"bootz ${loadaddr} ${rdaddr} ${fdtaddr}\0" \
"tftpboot=echo 'Booting kernel/ramdisk rootfs from tftp...'; " \
"run ramargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
"tftpboot ${loadaddr} ${zimage}; " \
"tftpboot ${rdaddr} ${ramdiskimage}; " \
"bootm ${loadaddr} ${rdaddr}\0" \
"tftpbootz=echo 'Booting kernel NFS rootfs...'; " \
"dhcp;" \
"run nfsargs;" \
"run common_bootargs;" \
"run dump_bootargs;" \
"tftpboot $loadaddr zImage;" \
"bootz $loadaddr\0" \
"nandbootcommon=echo 'Booting kernel from NAND...';" \
"run nandargs;" \
"run common_bootargs;" \
"run dump_bootargs;" \
"nand read ${loadaddr} kernel;" \
"nand read ${fdtaddr} spl-os;\0" \
"nandbootz=run nandbootcommon; "\
"bootz ${loadaddr} - ${fdtaddr}\0"\
"nandboot=run nandbootcommon; "\
"bootm ${loadaddr} - ${fdtaddr}\0"\
#define CONFIG_BOOTCOMMAND \
"run autoboot"
/* Miscellaneous configurable options */
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
/* FLASH and environment organization */
/* **** PISMO SUPPORT *** */
#if defined(CONFIG_CMD_NAND)
#define CONFIG_SYS_FLASH_BASE NAND_BASE
#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_ENV_OFFSET 0x260000
#define CONFIG_ENV_ADDR 0x260000
/* Defines for SPL */
/* NAND: SPL falcon mode configs */
#ifdef CONFIG_SPL_OS_BOOT
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
#endif
#endif /* __CONFIG_H */