u-boot/board/freescale/mpc8569mds/ddr.c
Haiying Wang b6bde93090 mpc8569mds: fix some ddr settings
Enable half drive strength, set RTT to 60Ohm and set write leveling override.

Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2010-10-07 09:49:47 -05:00

94 lines
2 KiB
C

/*
* Copyright 2009 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* Version 2 as published by the Free Software Foundation.
*/
#include <common.h>
#include <i2c.h>
#include <asm/fsl_ddr_sdram.h>
#include <asm/fsl_ddr_dimm_params.h>
static void
get_spd(ddr3_spd_eeprom_t *spd, unsigned char i2c_address)
{
i2c_read(i2c_address, 0, 1, (uchar *)spd, sizeof(ddr3_spd_eeprom_t));
}
unsigned int fsl_ddr_get_mem_data_rate(void)
{
return get_ddr_freq(0);
}
void fsl_ddr_get_spd(ddr3_spd_eeprom_t *ctrl_dimms_spd,
unsigned int ctrl_num)
{
unsigned int i;
unsigned int i2c_address = 0;
for (i = 0; i < CONFIG_DIMM_SLOTS_PER_CTLR; i++) {
if (ctrl_num == 0 && i == 0)
i2c_address = SPD_EEPROM_ADDRESS1;
if (ctrl_num == 0 && i == 1)
i2c_address = SPD_EEPROM_ADDRESS2;
get_spd(&(ctrl_dimms_spd[i]), i2c_address);
}
}
void fsl_ddr_board_options(memctl_options_t *popts,
dimm_params_t *pdimm,
unsigned int ctrl_num)
{
/*
* Factors to consider for clock adjust:
* - number of chips on bus
* - position of slot
* - DDR1 vs. DDR2?
* - ???
*
* This needs to be determined on a board-by-board basis.
* 0110 3/4 cycle late
* 0111 7/8 cycle late
*/
popts->clk_adjust = 4;
/*
* Factors to consider for CPO:
* - frequency
* - ddr1 vs. ddr2
*/
popts->cpo_override = 0xff;
/*
* Factors to consider for write data delay:
* - number of DIMMs
*
* 1 = 1/4 clock delay
* 2 = 1/2 clock delay
* 3 = 3/4 clock delay
* 4 = 1 clock delay
* 5 = 5/4 clock delay
* 6 = 3/2 clock delay
*/
popts->write_data_delay = 2;
/*
* Enable half drive strength
*/
popts->half_strength_driver_enable = 1;
/* Write leveling override */
popts->wrlvl_en = 1;
popts->wrlvl_override = 1;
popts->wrlvl_sample = 0xa;
popts->wrlvl_start = 0x4;
/* Rtt and Rtt_W override */
popts->rtt_override = 1;
popts->rtt_override_value = DDR3_RTT_60_OHM;
popts->rtt_wr_override_value = 0; /* Rtt_WR= dynamic ODT off */
}