u-boot/arch/arm/include/asm/arch-omap5/clock.h
Suman Anna fba82eb7c9 ARM: DRA7: Redefine voltage and efuse macros per OPP using Kconfig
Redefine the macros used to define the voltage values and the
efuse register offsets based on OPP for all the voltage domains.
This is done using Kconfig macros that can be set in a defconfig
or selected during a config step. This allows a voltage domain
to be configured/set to a corresponding voltage value depending
on the OPP selection choice.

The Kconfig choices have been added for MPU, DSPEVE, IVA and GPU
voltage domains, with the MPU domain restricted to OPP_NOM. The
OPP_OD and OPP_HIGH options will be added when the support for
configuring the MPU clock frequency is added. The clock
configuration for other voltage domains is out of scope in
u-boot code.

The CORE voltage domain does not have separate voltage values
and efuse register offset at different OPPs, while the MPU
voltage domain only has different efuse register offsets for
different OPPs, but uses the same voltage value. Any different
choices of OPPs for voltage domains on common ganged-rails
is automatically taken care to select the corresponding
highest OPP voltage value.

Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:48 -05:00

395 lines
12 KiB
C

/*
* (C) Copyright 2010
* Texas Instruments, <www.ti.com>
*
* Aneesh V <aneesh@ti.com>
* Sricharan R <r.sricharan@ti.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef _CLOCKS_OMAP5_H_
#define _CLOCKS_OMAP5_H_
#include <common.h>
#include <asm/omap_common.h>
/*
* Assuming a maximum of 1.5 GHz ARM speed and a minimum of 2 cycles per
* loop, allow for a minimum of 2 ms wait (in reality the wait will be
* much more than that)
*/
#define LDELAY 1000000
/* CM_DLL_CTRL */
#define CM_DLL_CTRL_OVERRIDE_SHIFT 0
#define CM_DLL_CTRL_OVERRIDE_MASK (1 << 0)
#define CM_DLL_CTRL_NO_OVERRIDE 0
/* CM_CLKMODE_DPLL */
#define CM_CLKMODE_DPLL_REGM4XEN_SHIFT 11
#define CM_CLKMODE_DPLL_REGM4XEN_MASK (1 << 11)
#define CM_CLKMODE_DPLL_LPMODE_EN_SHIFT 10
#define CM_CLKMODE_DPLL_LPMODE_EN_MASK (1 << 10)
#define CM_CLKMODE_DPLL_RELOCK_RAMP_EN_SHIFT 9
#define CM_CLKMODE_DPLL_RELOCK_RAMP_EN_MASK (1 << 9)
#define CM_CLKMODE_DPLL_DRIFTGUARD_EN_SHIFT 8
#define CM_CLKMODE_DPLL_DRIFTGUARD_EN_MASK (1 << 8)
#define CM_CLKMODE_DPLL_RAMP_RATE_SHIFT 5
#define CM_CLKMODE_DPLL_RAMP_RATE_MASK (0x7 << 5)
#define CM_CLKMODE_DPLL_EN_SHIFT 0
#define CM_CLKMODE_DPLL_EN_MASK (0x7 << 0)
#define CM_CLKMODE_DPLL_DPLL_EN_SHIFT 0
#define CM_CLKMODE_DPLL_DPLL_EN_MASK 7
#define DPLL_EN_STOP 1
#define DPLL_EN_MN_BYPASS 4
#define DPLL_EN_LOW_POWER_BYPASS 5
#define DPLL_EN_FAST_RELOCK_BYPASS 6
#define DPLL_EN_LOCK 7
/* CM_IDLEST_DPLL fields */
#define ST_DPLL_CLK_MASK 1
/* SGX */
#define CLKSEL_GPU_HYD_GCLK_MASK (1 << 25)
#define CLKSEL_GPU_CORE_GCLK_MASK (1 << 24)
/* CM_CLKSEL_DPLL */
#define CM_CLKSEL_DPLL_DPLL_SD_DIV_SHIFT 24
#define CM_CLKSEL_DPLL_DPLL_SD_DIV_MASK (0xFF << 24)
#define CM_CLKSEL_DPLL_M_SHIFT 8
#define CM_CLKSEL_DPLL_M_MASK (0x7FF << 8)
#define CM_CLKSEL_DPLL_N_SHIFT 0
#define CM_CLKSEL_DPLL_N_MASK 0x7F
#define CM_CLKSEL_DCC_EN_SHIFT 22
#define CM_CLKSEL_DCC_EN_MASK (1 << 22)
/* CM_SYS_CLKSEL */
#define CM_SYS_CLKSEL_SYS_CLKSEL_MASK 7
/* CM_CLKSEL_CORE */
#define CLKSEL_CORE_SHIFT 0
#define CLKSEL_L3_SHIFT 4
#define CLKSEL_L4_SHIFT 8
#define CLKSEL_CORE_X2_DIV_1 0
#define CLKSEL_L3_CORE_DIV_2 1
#define CLKSEL_L4_L3_DIV_2 1
/* CM_ABE_PLL_REF_CLKSEL */
#define CM_ABE_PLL_REF_CLKSEL_CLKSEL_SHIFT 0
#define CM_ABE_PLL_REF_CLKSEL_CLKSEL_MASK 1
#define CM_ABE_PLL_REF_CLKSEL_CLKSEL_SYSCLK 0
#define CM_ABE_PLL_REF_CLKSEL_CLKSEL_32KCLK 1
/* CM_CLKSEL_ABE_PLL_SYS */
#define CM_CLKSEL_ABE_PLL_SYS_CLKSEL_SHIFT 0
#define CM_CLKSEL_ABE_PLL_SYS_CLKSEL_MASK 1
#define CM_ABE_PLL_SYS_CLKSEL_SYSCLK1 0
#define CM_ABE_PLL_SYS_CLKSEL_SYSCLK2 1
/* CM_BYPCLK_DPLL_IVA */
#define CM_BYPCLK_DPLL_IVA_CLKSEL_SHIFT 0
#define CM_BYPCLK_DPLL_IVA_CLKSEL_MASK 3
#define DPLL_IVA_CLKSEL_CORE_X2_DIV_2 1
/* CM_SHADOW_FREQ_CONFIG1 */
#define SHADOW_FREQ_CONFIG1_FREQ_UPDATE_MASK 1
#define SHADOW_FREQ_CONFIG1_DLL_OVERRIDE_MASK 4
#define SHADOW_FREQ_CONFIG1_DLL_RESET_MASK 8
#define SHADOW_FREQ_CONFIG1_DPLL_EN_SHIFT 8
#define SHADOW_FREQ_CONFIG1_DPLL_EN_MASK (7 << 8)
#define SHADOW_FREQ_CONFIG1_M2_DIV_SHIFT 11
#define SHADOW_FREQ_CONFIG1_M2_DIV_MASK (0x1F << 11)
/*CM_<clock_domain>__CLKCTRL */
#define CD_CLKCTRL_CLKTRCTRL_SHIFT 0
#define CD_CLKCTRL_CLKTRCTRL_MASK 3
#define CD_CLKCTRL_CLKTRCTRL_NO_SLEEP 0
#define CD_CLKCTRL_CLKTRCTRL_SW_SLEEP 1
#define CD_CLKCTRL_CLKTRCTRL_SW_WKUP 2
#define CD_CLKCTRL_CLKTRCTRL_HW_AUTO 3
/* CM_<clock_domain>_<module>_CLKCTRL */
#define MODULE_CLKCTRL_MODULEMODE_SHIFT 0
#define MODULE_CLKCTRL_MODULEMODE_MASK 3
#define MODULE_CLKCTRL_IDLEST_SHIFT 16
#define MODULE_CLKCTRL_IDLEST_MASK (3 << 16)
#define MODULE_CLKCTRL_MODULEMODE_SW_DISABLE 0
#define MODULE_CLKCTRL_MODULEMODE_HW_AUTO 1
#define MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN 2
#define MODULE_CLKCTRL_IDLEST_FULLY_FUNCTIONAL 0
#define MODULE_CLKCTRL_IDLEST_TRANSITIONING 1
#define MODULE_CLKCTRL_IDLEST_IDLE 2
#define MODULE_CLKCTRL_IDLEST_DISABLED 3
/* CM_L4PER_GPIO4_CLKCTRL */
#define GPIO4_CLKCTRL_OPTFCLKEN_MASK (1 << 8)
/* CM_L3INIT_HSMMCn_CLKCTRL */
#define HSMMC_CLKCTRL_CLKSEL_MASK (1 << 24)
#define HSMMC_CLKCTRL_CLKSEL_DIV_MASK (1 << 25)
/* CM_L3INIT_SATA_CLKCTRL */
#define SATA_CLKCTRL_OPTFCLKEN_MASK (1 << 8)
/* CM_WKUP_GPTIMER1_CLKCTRL */
#define GPTIMER1_CLKCTRL_CLKSEL_MASK (1 << 24)
/* CM_CAM_ISS_CLKCTRL */
#define ISS_CLKCTRL_OPTFCLKEN_MASK (1 << 8)
/* CM_DSS_DSS_CLKCTRL */
#define DSS_CLKCTRL_OPTFCLKEN_MASK 0xF00
/* CM_L3INIT_USBPHY_CLKCTRL */
#define USBPHY_CLKCTRL_OPTFCLKEN_PHY_48M_MASK 8
/* CM_L3INIT_USB_HOST_HS_CLKCTRL */
#define OPTFCLKEN_FUNC48M_CLK (1 << 15)
#define OPTFCLKEN_HSIC480M_P2_CLK (1 << 14)
#define OPTFCLKEN_HSIC480M_P1_CLK (1 << 13)
#define OPTFCLKEN_HSIC60M_P2_CLK (1 << 12)
#define OPTFCLKEN_HSIC60M_P1_CLK (1 << 11)
#define OPTFCLKEN_UTMI_P3_CLK (1 << 10)
#define OPTFCLKEN_UTMI_P2_CLK (1 << 9)
#define OPTFCLKEN_UTMI_P1_CLK (1 << 8)
#define OPTFCLKEN_HSIC480M_P3_CLK (1 << 7)
#define OPTFCLKEN_HSIC60M_P3_CLK (1 << 6)
/* CM_L3INIT_USB_TLL_HS_CLKCTRL */
#define OPTFCLKEN_USB_CH0_CLK_ENABLE (1 << 8)
#define OPTFCLKEN_USB_CH1_CLK_ENABLE (1 << 9)
#define OPTFCLKEN_USB_CH2_CLK_ENABLE (1 << 10)
/* CM_COREAON_USB_PHY_CORE_CLKCTRL */
#define USBPHY_CORE_CLKCTRL_OPTFCLKEN_CLK32K (1 << 8)
/* CM_COREAON_L3INIT_60M_GFCLK_CLKCTRL */
#define L3INIT_CLKCTRL_OPTFCLKEN_60M_GFCLK (1 << 8)
/* CM_L3INIT_USB_OTG_SS_CLKCTRL */
#define OTG_SS_CLKCTRL_MODULEMODE_HW (1 << 0)
#define OPTFCLKEN_REFCLK960M (1 << 8)
/* CM_L3INIT_OCP2SCP1_CLKCTRL */
#define OCP2SCP1_CLKCTRL_MODULEMODE_HW (1 << 0)
/* CM_MPU_MPU_CLKCTRL */
#define MPU_CLKCTRL_CLKSEL_EMIF_DIV_MODE_SHIFT 24
#define MPU_CLKCTRL_CLKSEL_EMIF_DIV_MODE_MASK (3 << 24)
#define MPU_CLKCTRL_CLKSEL_ABE_DIV_MODE_SHIFT 26
#define MPU_CLKCTRL_CLKSEL_ABE_DIV_MODE_MASK (1 << 26)
/* CM_WKUPAON_SCRM_CLKCTRL */
#define OPTFCLKEN_SCRM_PER_SHIFT 9
#define OPTFCLKEN_SCRM_PER_MASK (1 << 9)
#define OPTFCLKEN_SCRM_CORE_SHIFT 8
#define OPTFCLKEN_SCRM_CORE_MASK (1 << 8)
/* CM_COREAON_IO_SRCOMP_CLKCTRL */
#define OPTFCLKEN_SRCOMP_FCLK_SHIFT 8
#define OPTFCLKEN_SRCOMP_FCLK_MASK (1 << 8)
/* PRM_RSTTIME */
#define RSTTIME1_SHIFT 0
#define RSTTIME1_MASK (0x3ff << 0)
/* Clock frequencies */
#define OMAP_SYS_CLK_IND_38_4_MHZ 6
/* PRM_VC_VAL_BYPASS */
#define PRM_VC_I2C_CHANNEL_FREQ_KHZ 400
/* CTRL_CORE_SRCOMP_NORTH_SIDE */
#define USB2PHY_DISCHGDET (1 << 29)
#define USB2PHY_AUTORESUME_EN (1 << 30)
/* SMPS */
#define SMPS_I2C_SLAVE_ADDR 0x12
#define SMPS_REG_ADDR_12_MPU 0x23
#define SMPS_REG_ADDR_45_IVA 0x2B
#define SMPS_REG_ADDR_8_CORE 0x37
/* PALMAS VOLTAGE SETTINGS in mv for OPP_NOMINAL */
/* ES1.0 settings */
#define VDD_MPU 1040
#define VDD_MM 1040
#define VDD_CORE 1040
#define VDD_MPU_LOW 890
#define VDD_MM_LOW 890
#define VDD_CORE_LOW 890
/* ES2.0 settings */
#define VDD_MPU_ES2 1060
#define VDD_MM_ES2 1025
#define VDD_CORE_ES2 1040
#define VDD_MPU_ES2_HIGH 1250
#define VDD_MM_ES2_OD 1120
#define VDD_MPU_ES2_LOW 880
#define VDD_MM_ES2_LOW 880
/* DRA74x/75x/72x voltage settings in mv for OPP_NOM per DM */
#define VDD_MPU_DRA7_NOM 1150
#define VDD_CORE_DRA7_NOM 1150
#define VDD_EVE_DRA7_NOM 1060
#define VDD_GPU_DRA7_NOM 1060
#define VDD_IVA_DRA7_NOM 1060
/* DRA74x/75x/72x voltage settings in mv for OPP_OD per DM */
#define VDD_EVE_DRA7_OD 1150
#define VDD_GPU_DRA7_OD 1150
#define VDD_IVA_DRA7_OD 1150
/* DRA74x/75x/72x voltage settings in mv for OPP_HIGH per DM */
#define VDD_EVE_DRA7_HIGH 1250
#define VDD_GPU_DRA7_HIGH 1250
#define VDD_IVA_DRA7_HIGH 1250
/* Efuse register offsets for DRA7xx platform */
#define DRA752_EFUSE_BASE 0x4A002000
#define DRA752_EFUSE_REGBITS 16
/* STD_FUSE_OPP_VMIN_IVA_2 */
#define STD_FUSE_OPP_VMIN_IVA_NOM (DRA752_EFUSE_BASE + 0x05CC)
/* STD_FUSE_OPP_VMIN_IVA_3 */
#define STD_FUSE_OPP_VMIN_IVA_OD (DRA752_EFUSE_BASE + 0x05D0)
/* STD_FUSE_OPP_VMIN_IVA_4 */
#define STD_FUSE_OPP_VMIN_IVA_HIGH (DRA752_EFUSE_BASE + 0x05D4)
/* STD_FUSE_OPP_VMIN_DSPEVE_2 */
#define STD_FUSE_OPP_VMIN_DSPEVE_NOM (DRA752_EFUSE_BASE + 0x05E0)
/* STD_FUSE_OPP_VMIN_DSPEVE_3 */
#define STD_FUSE_OPP_VMIN_DSPEVE_OD (DRA752_EFUSE_BASE + 0x05E4)
/* STD_FUSE_OPP_VMIN_DSPEVE_4 */
#define STD_FUSE_OPP_VMIN_DSPEVE_HIGH (DRA752_EFUSE_BASE + 0x05E8)
/* STD_FUSE_OPP_VMIN_CORE_2 */
#define STD_FUSE_OPP_VMIN_CORE_NOM (DRA752_EFUSE_BASE + 0x05F4)
/* STD_FUSE_OPP_VMIN_GPU_2 */
#define STD_FUSE_OPP_VMIN_GPU_NOM (DRA752_EFUSE_BASE + 0x1B08)
/* STD_FUSE_OPP_VMIN_GPU_3 */
#define STD_FUSE_OPP_VMIN_GPU_OD (DRA752_EFUSE_BASE + 0x1B0C)
/* STD_FUSE_OPP_VMIN_GPU_4 */
#define STD_FUSE_OPP_VMIN_GPU_HIGH (DRA752_EFUSE_BASE + 0x1B10)
/* STD_FUSE_OPP_VMIN_MPU_2 */
#define STD_FUSE_OPP_VMIN_MPU_NOM (DRA752_EFUSE_BASE + 0x1B20)
/* STD_FUSE_OPP_VMIN_MPU_3 */
#define STD_FUSE_OPP_VMIN_MPU_OD (DRA752_EFUSE_BASE + 0x1B24)
/* STD_FUSE_OPP_VMIN_MPU_4 */
#define STD_FUSE_OPP_VMIN_MPU_HIGH (DRA752_EFUSE_BASE + 0x1B28)
#if defined(CONFIG_DRA7_MPU_OPP_HIGH)
#define DRA7_MPU_OPP OPP_HIGH
#elif defined(CONFIG_DRA7_MPU_OPP_OD)
#define DRA7_MPU_OPP OPP_OD
#else /* OPP_NOM default */
#define DRA7_MPU_OPP OPP_NOM
#endif
/* OPP_NOM only available option for CORE */
#define DRA7_CORE_OPP OPP_NOM
#if defined(CONFIG_DRA7_DSPEVE_OPP_HIGH)
#define DRA7_DSPEVE_OPP OPP_HIGH
#elif defined(CONFIG_DRA7_DSPEVE_OPP_OD)
#define DRA7_DSPEVE_OPP OPP_OD
#else /* OPP_NOM default */
#define DRA7_DSPEVE_OPP OPP_NOM
#endif
#if defined(CONFIG_DRA7_IVA_OPP_HIGH)
#define DRA7_IVA_OPP OPP_HIGH
#elif defined(CONFIG_DRA7_IVA_OPP_OD)
#define DRA7_IVA_OPP OPP_OD
#else /* OPP_NOM default */
#define DRA7_IVA_OPP OPP_NOM
#endif
#if defined(CONFIG_DRA7_GPU_OPP_HIGH)
#define DRA7_GPU_OPP OPP_HIGH
#elif defined(CONFIG_DRA7_GPU_OPP_OD)
#define DRA7_GPU_OPP OPP_OD
#else /* OPP_NOM default */
#define DRA7_GPU_OPP OPP_NOM
#endif
/* Standard offset is 0.5v expressed in uv */
#define PALMAS_SMPS_BASE_VOLT_UV 500000
/* TPS659038 */
#define TPS659038_I2C_SLAVE_ADDR 0x58
#define TPS659038_REG_ADDR_SMPS12 0x23
#define TPS659038_REG_ADDR_SMPS45 0x2B
#define TPS659038_REG_ADDR_SMPS6 0x2F
#define TPS659038_REG_ADDR_SMPS7 0x33
#define TPS659038_REG_ADDR_SMPS8 0x37
/* TPS65917 */
#define TPS65917_I2C_SLAVE_ADDR 0x58
#define TPS65917_REG_ADDR_SMPS1 0x23
#define TPS65917_REG_ADDR_SMPS2 0x27
#define TPS65917_REG_ADDR_SMPS3 0x2F
/* TPS */
#define TPS62361_I2C_SLAVE_ADDR 0x60
#define TPS62361_REG_ADDR_SET0 0x0
#define TPS62361_REG_ADDR_SET1 0x1
#define TPS62361_REG_ADDR_SET2 0x2
#define TPS62361_REG_ADDR_SET3 0x3
#define TPS62361_REG_ADDR_CTRL 0x4
#define TPS62361_REG_ADDR_TEMP 0x5
#define TPS62361_REG_ADDR_RMP_CTRL 0x6
#define TPS62361_REG_ADDR_CHIP_ID 0x8
#define TPS62361_REG_ADDR_CHIP_ID_2 0x9
#define TPS62361_BASE_VOLT_MV 500
#define TPS62361_VSEL0_GPIO 7
/* Defines for DPLL setup */
#define DPLL_LOCKED_FREQ_TOLERANCE_0 0
#define DPLL_LOCKED_FREQ_TOLERANCE_500_KHZ 500
#define DPLL_LOCKED_FREQ_TOLERANCE_1_MHZ 1000
#define DPLL_NO_LOCK 0
#define DPLL_LOCK 1
/*
* MAX value for PRM_RSTTIME[9:0]RSTTIME1 stored is 0x3ff.
* 0x3ff is in the no of FUNC_32K_CLK cycles. Converting cycles
* into microsec and passing the value.
*/
#define CONFIG_DEFAULT_OMAP_RESET_TIME_MAX_USEC 31219
#if defined(CONFIG_DRA7XX)
#define V_OSCK 20000000 /* Clock output from T2 */
#else
#define V_OSCK 19200000 /* Clock output from T2 */
#endif
#define V_SCLK V_OSCK
/* CKO buffer control */
#define CKOBUFFER_CLK_ENABLE_MASK (1 << 28)
/* AUXCLKx reg fields */
#define AUXCLK_ENABLE_MASK (1 << 8)
#define AUXCLK_SRCSELECT_SHIFT 1
#define AUXCLK_SRCSELECT_MASK (3 << 1)
#define AUXCLK_CLKDIV_SHIFT 16
#define AUXCLK_CLKDIV_MASK (0xF << 16)
#define AUXCLK_SRCSELECT_SYS_CLK 0
#define AUXCLK_SRCSELECT_CORE_DPLL 1
#define AUXCLK_SRCSELECT_PER_DPLL 2
#define AUXCLK_SRCSELECT_ALTERNATE 3
#endif /* _CLOCKS_OMAP5_H_ */