mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-17 10:18:38 +00:00
031acdbae8
Set up chip power supply voltage according to voltage ID. The fuse status register provides the values from on-chip voltage ID fuses programmed at the factory. These values define the voltage requirements for the chip. Main operations: 1. Set up the core voltage 2. Set up the SERDES voltage and reset SERDES lanes 3. Enable/disable DDR controller support 0.9V if needed Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com> Reviewed-by: York Sun <york.sun@nxp.com>
420 lines
10 KiB
C
420 lines
10 KiB
C
/*
|
||
* Copyright 2015 Freescale Semiconductor, Inc.
|
||
*
|
||
* SPDX-License-Identifier: GPL-2.0+
|
||
*/
|
||
|
||
#include <common.h>
|
||
#include <asm/io.h>
|
||
#include <linux/errno.h>
|
||
#include <asm/arch/fsl_serdes.h>
|
||
#include <asm/arch/soc.h>
|
||
|
||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||
static u8 serdes1_prtcl_map[SERDES_PRCTL_COUNT];
|
||
#endif
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
static u8 serdes2_prtcl_map[SERDES_PRCTL_COUNT];
|
||
#endif
|
||
|
||
int is_serdes_configured(enum srds_prtcl device)
|
||
{
|
||
int ret = 0;
|
||
|
||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||
if (!serdes1_prtcl_map[NONE])
|
||
fsl_serdes_init();
|
||
|
||
ret |= serdes1_prtcl_map[device];
|
||
#endif
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
if (!serdes2_prtcl_map[NONE])
|
||
fsl_serdes_init();
|
||
|
||
ret |= serdes2_prtcl_map[device];
|
||
#endif
|
||
|
||
return !!ret;
|
||
}
|
||
|
||
int serdes_get_first_lane(u32 sd, enum srds_prtcl device)
|
||
{
|
||
struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
|
||
u32 cfg = gur_in32(&gur->rcwsr[4]);
|
||
int i;
|
||
|
||
switch (sd) {
|
||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||
case FSL_SRDS_1:
|
||
cfg &= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
|
||
cfg >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
|
||
break;
|
||
#endif
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
case FSL_SRDS_2:
|
||
cfg &= FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK;
|
||
cfg >>= FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT;
|
||
break;
|
||
#endif
|
||
default:
|
||
printf("invalid SerDes%d\n", sd);
|
||
break;
|
||
}
|
||
|
||
/* Is serdes enabled at all? */
|
||
if (unlikely(cfg == 0))
|
||
return -ENODEV;
|
||
|
||
for (i = 0; i < SRDS_MAX_LANES; i++) {
|
||
if (serdes_get_prtcl(sd, cfg, i) == device)
|
||
return i;
|
||
}
|
||
|
||
return -ENODEV;
|
||
}
|
||
|
||
int get_serdes_protocol(void)
|
||
{
|
||
struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
|
||
u32 cfg = gur_in32(&gur->rcwsr[4]) &
|
||
FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
|
||
cfg >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
|
||
|
||
return cfg;
|
||
}
|
||
|
||
const char *serdes_clock_to_string(u32 clock)
|
||
{
|
||
switch (clock) {
|
||
case SRDS_PLLCR0_RFCK_SEL_100:
|
||
return "100";
|
||
case SRDS_PLLCR0_RFCK_SEL_125:
|
||
return "125";
|
||
case SRDS_PLLCR0_RFCK_SEL_156_25:
|
||
return "156.25";
|
||
default:
|
||
return "100";
|
||
}
|
||
}
|
||
|
||
void serdes_init(u32 sd, u32 sd_addr, u32 sd_prctl_mask, u32 sd_prctl_shift,
|
||
u8 serdes_prtcl_map[SERDES_PRCTL_COUNT])
|
||
{
|
||
struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
|
||
u32 cfg;
|
||
int lane;
|
||
|
||
if (serdes_prtcl_map[NONE])
|
||
return;
|
||
|
||
memset(serdes_prtcl_map, 0, sizeof(u8) * SERDES_PRCTL_COUNT);
|
||
|
||
cfg = gur_in32(&gur->rcwsr[4]) & sd_prctl_mask;
|
||
cfg >>= sd_prctl_shift;
|
||
printf("Using SERDES%d Protocol: %d (0x%x)\n", sd + 1, cfg, cfg);
|
||
|
||
if (!is_serdes_prtcl_valid(sd, cfg))
|
||
printf("SERDES%d[PRTCL] = 0x%x is not valid\n", sd + 1, cfg);
|
||
|
||
for (lane = 0; lane < SRDS_MAX_LANES; lane++) {
|
||
enum srds_prtcl lane_prtcl = serdes_get_prtcl(sd, cfg, lane);
|
||
|
||
if (unlikely(lane_prtcl >= SERDES_PRCTL_COUNT))
|
||
debug("Unknown SerDes lane protocol %d\n", lane_prtcl);
|
||
else
|
||
serdes_prtcl_map[lane_prtcl] = 1;
|
||
}
|
||
|
||
/* Set the first element to indicate serdes has been initialized */
|
||
serdes_prtcl_map[NONE] = 1;
|
||
}
|
||
|
||
__weak int get_serdes_volt(void)
|
||
{
|
||
return -1;
|
||
}
|
||
|
||
__weak int set_serdes_volt(int svdd)
|
||
{
|
||
return -1;
|
||
}
|
||
|
||
int setup_serdes_volt(u32 svdd)
|
||
{
|
||
struct ccsr_gur __iomem *gur = (void *)(CONFIG_SYS_FSL_GUTS_ADDR);
|
||
struct ccsr_serdes *serdes1_base;
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
struct ccsr_serdes *serdes2_base;
|
||
#endif
|
||
u32 cfg_rcw4 = gur_in32(&gur->rcwsr[4]);
|
||
u32 cfg_rcw5 = gur_in32(&gur->rcwsr[5]);
|
||
u32 cfg_tmp, reg = 0;
|
||
int svdd_cur, svdd_tar;
|
||
int ret;
|
||
int i;
|
||
|
||
/* Only support switch SVDD to 900mV/1000mV */
|
||
if (svdd != 900 && svdd != 1000)
|
||
return -EINVAL;
|
||
|
||
svdd_tar = svdd;
|
||
svdd_cur = get_serdes_volt();
|
||
if (svdd_cur < 0)
|
||
return -EINVAL;
|
||
|
||
debug("%s: current SVDD: %dmV; target SVDD: %dmV\n",
|
||
__func__, svdd_cur, svdd_tar);
|
||
if (svdd_cur == svdd_tar)
|
||
return 0;
|
||
|
||
serdes1_base = (void *)CONFIG_SYS_FSL_SERDES_ADDR;
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
serdes2_base = (void *)serdes1_base + 0x10000;
|
||
#endif
|
||
|
||
/* Put the all enabled lanes in reset */
|
||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||
cfg_tmp = cfg_rcw4 & FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
|
||
cfg_tmp >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
|
||
|
||
for (i = 0; i < 4 && cfg_tmp & (0xf << (3 - i)); i++) {
|
||
reg = in_be32(&serdes1_base->lane[i].gcr0);
|
||
reg &= 0xFF9FFFFF;
|
||
out_be32(&serdes1_base->lane[i].gcr0, reg);
|
||
}
|
||
#endif
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
cfg_tmp = cfg_rcw4 & FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK;
|
||
cfg_tmp >>= FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT;
|
||
|
||
for (i = 0; i < 4 && cfg_tmp & (0xf << (3 - i)); i++) {
|
||
reg = in_be32(&serdes2_base->lane[i].gcr0);
|
||
reg &= 0xFF9FFFFF;
|
||
out_be32(&serdes2_base->lane[i].gcr0, reg);
|
||
}
|
||
#endif
|
||
|
||
/* Put the all enabled PLL in reset */
|
||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||
cfg_tmp = (cfg_rcw5 >> 22) & 0x3;
|
||
for (i = 0; i < 2 && !(cfg_tmp & (0x1 << (1 - i))); i++) {
|
||
reg = in_be32(&serdes1_base->bank[i].rstctl);
|
||
reg &= 0xFFFFFFBF;
|
||
reg |= 0x10000000;
|
||
out_be32(&serdes1_base->bank[i].rstctl, reg);
|
||
udelay(1);
|
||
|
||
reg = in_be32(&serdes1_base->bank[i].rstctl);
|
||
reg &= 0xFFFFFF1F;
|
||
out_be32(&serdes1_base->bank[i].rstctl, reg);
|
||
}
|
||
udelay(1);
|
||
#endif
|
||
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
cfg_tmp = (cfg_rcw5 >> 20) & 0x3;
|
||
for (i = 0; i < 2 && !(cfg_tmp & (0x1 << (1 - i))); i++) {
|
||
reg = in_be32(&serdes2_base->bank[i].rstctl);
|
||
reg &= 0xFFFFFFBF;
|
||
reg |= 0x10000000;
|
||
out_be32(&serdes2_base->bank[i].rstctl, reg);
|
||
udelay(1);
|
||
|
||
reg = in_be32(&serdes2_base->bank[i].rstctl);
|
||
reg &= 0xFFFFFF1F;
|
||
out_be32(&serdes2_base->bank[i].rstctl, reg);
|
||
}
|
||
udelay(1);
|
||
#endif
|
||
|
||
/* Put the Rx/Tx calibration into reset */
|
||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||
reg = in_be32(&serdes1_base->srdstcalcr);
|
||
reg &= 0xF7FFFFFF;
|
||
out_be32(&serdes1_base->srdstcalcr, reg);
|
||
reg = in_be32(&serdes1_base->srdsrcalcr);
|
||
reg &= 0xF7FFFFFF;
|
||
out_be32(&serdes1_base->srdsrcalcr, reg);
|
||
|
||
#endif
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
reg = in_be32(&serdes2_base->srdstcalcr);
|
||
reg &= 0xF7FFFFFF;
|
||
out_be32(&serdes2_base->srdstcalcr, reg);
|
||
reg = in_be32(&serdes2_base->srdsrcalcr);
|
||
reg &= 0xF7FFFFFF;
|
||
out_be32(&serdes2_base->srdsrcalcr, reg);
|
||
#endif
|
||
|
||
/*
|
||
* If SVDD set failed, will not return directly, so that the
|
||
* serdes lanes can complete reseting.
|
||
*/
|
||
ret = set_serdes_volt(svdd_tar);
|
||
if (ret)
|
||
printf("%s: Failed to set SVDD\n", __func__);
|
||
|
||
/* Wait for SVDD to stabilize */
|
||
udelay(100);
|
||
|
||
/* For each PLL that’s not disabled via RCW */
|
||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||
cfg_tmp = (cfg_rcw5 >> 22) & 0x3;
|
||
for (i = 0; i < 2 && !(cfg_tmp & (0x1 << (1 - i))); i++) {
|
||
reg = in_be32(&serdes1_base->bank[i].rstctl);
|
||
reg |= 0x00000020;
|
||
out_be32(&serdes1_base->bank[i].rstctl, reg);
|
||
udelay(1);
|
||
|
||
reg = in_be32(&serdes1_base->bank[i].rstctl);
|
||
reg |= 0x00000080;
|
||
out_be32(&serdes1_base->bank[i].rstctl, reg);
|
||
|
||
/* Take the Rx/Tx calibration out of reset */
|
||
if (!(cfg_tmp == 0x3 && i == 1)) {
|
||
udelay(1);
|
||
reg = in_be32(&serdes1_base->srdstcalcr);
|
||
reg |= 0x08000000;
|
||
out_be32(&serdes1_base->srdstcalcr, reg);
|
||
reg = in_be32(&serdes1_base->srdsrcalcr);
|
||
reg |= 0x08000000;
|
||
out_be32(&serdes1_base->srdsrcalcr, reg);
|
||
}
|
||
}
|
||
udelay(1);
|
||
#endif
|
||
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
cfg_tmp = (cfg_rcw5 >> 20) & 0x3;
|
||
for (i = 0; i < 2 && !(cfg_tmp & (0x1 << (1 - i))); i++) {
|
||
reg = in_be32(&serdes2_base->bank[i].rstctl);
|
||
reg |= 0x00000020;
|
||
out_be32(&serdes2_base->bank[i].rstctl, reg);
|
||
udelay(1);
|
||
|
||
reg = in_be32(&serdes2_base->bank[i].rstctl);
|
||
reg |= 0x00000080;
|
||
out_be32(&serdes2_base->bank[i].rstctl, reg);
|
||
|
||
/* Take the Rx/Tx calibration out of reset */
|
||
if (!(cfg_tmp == 0x3 && i == 1)) {
|
||
udelay(1);
|
||
reg = in_be32(&serdes2_base->srdstcalcr);
|
||
reg |= 0x08000000;
|
||
out_be32(&serdes2_base->srdstcalcr, reg);
|
||
reg = in_be32(&serdes2_base->srdsrcalcr);
|
||
reg |= 0x08000000;
|
||
out_be32(&serdes2_base->srdsrcalcr, reg);
|
||
}
|
||
}
|
||
udelay(1);
|
||
|
||
#endif
|
||
|
||
/* Wait for at lesat 625us to ensure the PLLs being reset are locked */
|
||
udelay(800);
|
||
|
||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||
cfg_tmp = (cfg_rcw5 >> 22) & 0x3;
|
||
for (i = 0; i < 2 && !(cfg_tmp & (0x1 << (1 - i))); i++) {
|
||
/* if the PLL is not locked, set RST_ERR */
|
||
reg = in_be32(&serdes1_base->bank[i].pllcr0);
|
||
if (!((reg >> 23) & 0x1)) {
|
||
reg = in_be32(&serdes1_base->bank[i].rstctl);
|
||
reg |= 0x20000000;
|
||
out_be32(&serdes1_base->bank[i].rstctl, reg);
|
||
} else {
|
||
udelay(1);
|
||
reg = in_be32(&serdes1_base->bank[i].rstctl);
|
||
reg &= 0xFFFFFFEF;
|
||
reg |= 0x00000040;
|
||
out_be32(&serdes1_base->bank[i].rstctl, reg);
|
||
udelay(1);
|
||
}
|
||
}
|
||
#endif
|
||
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
cfg_tmp = (cfg_rcw5 >> 20) & 0x3;
|
||
for (i = 0; i < 2 && !(cfg_tmp & (0x1 << (1 - i))); i++) {
|
||
reg = in_be32(&serdes2_base->bank[i].pllcr0);
|
||
if (!((reg >> 23) & 0x1)) {
|
||
reg = in_be32(&serdes2_base->bank[i].rstctl);
|
||
reg |= 0x20000000;
|
||
out_be32(&serdes2_base->bank[i].rstctl, reg);
|
||
} else {
|
||
udelay(1);
|
||
reg = in_be32(&serdes2_base->bank[i].rstctl);
|
||
reg &= 0xFFFFFFEF;
|
||
reg |= 0x00000040;
|
||
out_be32(&serdes2_base->bank[i].rstctl, reg);
|
||
udelay(1);
|
||
}
|
||
}
|
||
#endif
|
||
|
||
/* Take the all enabled lanes out of reset */
|
||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||
cfg_tmp = cfg_rcw4 & FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK;
|
||
cfg_tmp >>= FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT;
|
||
|
||
for (i = 0; i < 4 && cfg_tmp & (0xf << (3 - i)); i++) {
|
||
reg = in_be32(&serdes1_base->lane[i].gcr0);
|
||
reg |= 0x00600000;
|
||
out_be32(&serdes1_base->lane[i].gcr0, reg);
|
||
}
|
||
#endif
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
cfg_tmp = cfg_rcw4 & FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK;
|
||
cfg_tmp >>= FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT;
|
||
|
||
for (i = 0; i < 4 && cfg_tmp & (0xf << (3 - i)); i++) {
|
||
reg = in_be32(&serdes2_base->lane[i].gcr0);
|
||
reg |= 0x00600000;
|
||
out_be32(&serdes2_base->lane[i].gcr0, reg);
|
||
}
|
||
#endif
|
||
/* For each PLL being reset, and achieved PLL lock set RST_DONE */
|
||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||
cfg_tmp = (cfg_rcw5 >> 22) & 0x3;
|
||
for (i = 0; i < 2; i++) {
|
||
reg = in_be32(&serdes1_base->bank[i].pllcr0);
|
||
if (!(cfg_tmp & (0x1 << (1 - i))) && ((reg >> 23) & 0x1)) {
|
||
reg = in_be32(&serdes1_base->bank[i].rstctl);
|
||
reg |= 0x40000000;
|
||
out_be32(&serdes1_base->bank[i].rstctl, reg);
|
||
}
|
||
}
|
||
#endif
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
cfg_tmp = (cfg_rcw5 >> 20) & 0x3;
|
||
for (i = 0; i < 2; i++) {
|
||
reg = in_be32(&serdes2_base->bank[i].pllcr0);
|
||
if (!(cfg_tmp & (0x1 << (1 - i))) && ((reg >> 23) & 0x1)) {
|
||
reg = in_be32(&serdes2_base->bank[i].rstctl);
|
||
reg |= 0x40000000;
|
||
out_be32(&serdes2_base->bank[i].rstctl, reg);
|
||
}
|
||
}
|
||
#endif
|
||
|
||
return ret;
|
||
}
|
||
|
||
void fsl_serdes_init(void)
|
||
{
|
||
#ifdef CONFIG_SYS_FSL_SRDS_1
|
||
serdes_init(FSL_SRDS_1,
|
||
CONFIG_SYS_FSL_SERDES_ADDR,
|
||
FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_MASK,
|
||
FSL_CHASSIS2_RCWSR4_SRDS1_PRTCL_SHIFT,
|
||
serdes1_prtcl_map);
|
||
#endif
|
||
#ifdef CONFIG_SYS_FSL_SRDS_2
|
||
serdes_init(FSL_SRDS_2,
|
||
CONFIG_SYS_FSL_SERDES_ADDR,
|
||
FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_MASK,
|
||
FSL_CHASSIS2_RCWSR4_SRDS2_PRTCL_SHIFT,
|
||
serdes2_prtcl_map);
|
||
#endif
|
||
}
|