mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-12 22:33:18 +00:00
e22cc0cf13
Writing magic bits into LDO SRAM was suggested only for OMAP5432 ES1.0. Now these are no longer applicable. Moreover these bits should not be overwritten as they are loaded from EFUSE. So avoid writing into these registers. Boot tested on OMAP5432 ES2.0 Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
785 lines
21 KiB
C
785 lines
21 KiB
C
/*
|
|
*
|
|
* Clock initialization for OMAP4
|
|
*
|
|
* (C) Copyright 2010
|
|
* Texas Instruments, <www.ti.com>
|
|
*
|
|
* Aneesh V <aneesh@ti.com>
|
|
*
|
|
* Based on previous work by:
|
|
* Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
* Rajendra Nayak <rnayak@ti.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
#include <common.h>
|
|
#include <i2c.h>
|
|
#include <asm/omap_common.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/utils.h>
|
|
#include <asm/omap_gpio.h>
|
|
#include <asm/emif.h>
|
|
|
|
#ifndef CONFIG_SPL_BUILD
|
|
/*
|
|
* printing to console doesn't work unless
|
|
* this code is executed from SPL
|
|
*/
|
|
#define printf(fmt, args...)
|
|
#define puts(s)
|
|
#endif
|
|
|
|
const u32 sys_clk_array[8] = {
|
|
12000000, /* 12 MHz */
|
|
20000000, /* 20 MHz */
|
|
16800000, /* 16.8 MHz */
|
|
19200000, /* 19.2 MHz */
|
|
26000000, /* 26 MHz */
|
|
27000000, /* 27 MHz */
|
|
38400000, /* 38.4 MHz */
|
|
};
|
|
|
|
static inline u32 __get_sys_clk_index(void)
|
|
{
|
|
s8 ind;
|
|
/*
|
|
* For ES1 the ROM code calibration of sys clock is not reliable
|
|
* due to hw issue. So, use hard-coded value. If this value is not
|
|
* correct for any board over-ride this function in board file
|
|
* From ES2.0 onwards you will get this information from
|
|
* CM_SYS_CLKSEL
|
|
*/
|
|
if (omap_revision() == OMAP4430_ES1_0)
|
|
ind = OMAP_SYS_CLK_IND_38_4_MHZ;
|
|
else {
|
|
/* SYS_CLKSEL - 1 to match the dpll param array indices */
|
|
ind = (readl((*prcm)->cm_sys_clksel) &
|
|
CM_SYS_CLKSEL_SYS_CLKSEL_MASK) - 1;
|
|
}
|
|
return ind;
|
|
}
|
|
|
|
u32 get_sys_clk_index(void)
|
|
__attribute__ ((weak, alias("__get_sys_clk_index")));
|
|
|
|
u32 get_sys_clk_freq(void)
|
|
{
|
|
u8 index = get_sys_clk_index();
|
|
return sys_clk_array[index];
|
|
}
|
|
|
|
void setup_post_dividers(u32 const base, const struct dpll_params *params)
|
|
{
|
|
struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
|
|
|
|
/* Setup post-dividers */
|
|
if (params->m2 >= 0)
|
|
writel(params->m2, &dpll_regs->cm_div_m2_dpll);
|
|
if (params->m3 >= 0)
|
|
writel(params->m3, &dpll_regs->cm_div_m3_dpll);
|
|
if (params->m4_h11 >= 0)
|
|
writel(params->m4_h11, &dpll_regs->cm_div_m4_h11_dpll);
|
|
if (params->m5_h12 >= 0)
|
|
writel(params->m5_h12, &dpll_regs->cm_div_m5_h12_dpll);
|
|
if (params->m6_h13 >= 0)
|
|
writel(params->m6_h13, &dpll_regs->cm_div_m6_h13_dpll);
|
|
if (params->m7_h14 >= 0)
|
|
writel(params->m7_h14, &dpll_regs->cm_div_m7_h14_dpll);
|
|
if (params->h21 >= 0)
|
|
writel(params->h21, &dpll_regs->cm_div_h21_dpll);
|
|
if (params->h22 >= 0)
|
|
writel(params->h22, &dpll_regs->cm_div_h22_dpll);
|
|
if (params->h23 >= 0)
|
|
writel(params->h23, &dpll_regs->cm_div_h23_dpll);
|
|
if (params->h24 >= 0)
|
|
writel(params->h24, &dpll_regs->cm_div_h24_dpll);
|
|
}
|
|
|
|
static inline void do_bypass_dpll(u32 const base)
|
|
{
|
|
struct dpll_regs *dpll_regs = (struct dpll_regs *)base;
|
|
|
|
clrsetbits_le32(&dpll_regs->cm_clkmode_dpll,
|
|
CM_CLKMODE_DPLL_DPLL_EN_MASK,
|
|
DPLL_EN_FAST_RELOCK_BYPASS <<
|
|
CM_CLKMODE_DPLL_EN_SHIFT);
|
|
}
|
|
|
|
static inline void wait_for_bypass(u32 const base)
|
|
{
|
|
struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
|
|
|
|
if (!wait_on_value(ST_DPLL_CLK_MASK, 0, &dpll_regs->cm_idlest_dpll,
|
|
LDELAY)) {
|
|
printf("Bypassing DPLL failed %x\n", base);
|
|
}
|
|
}
|
|
|
|
static inline void do_lock_dpll(u32 const base)
|
|
{
|
|
struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
|
|
|
|
clrsetbits_le32(&dpll_regs->cm_clkmode_dpll,
|
|
CM_CLKMODE_DPLL_DPLL_EN_MASK,
|
|
DPLL_EN_LOCK << CM_CLKMODE_DPLL_EN_SHIFT);
|
|
}
|
|
|
|
static inline void wait_for_lock(u32 const base)
|
|
{
|
|
struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
|
|
|
|
if (!wait_on_value(ST_DPLL_CLK_MASK, ST_DPLL_CLK_MASK,
|
|
&dpll_regs->cm_idlest_dpll, LDELAY)) {
|
|
printf("DPLL locking failed for %x\n", base);
|
|
hang();
|
|
}
|
|
}
|
|
|
|
inline u32 check_for_lock(u32 const base)
|
|
{
|
|
struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
|
|
u32 lock = readl(&dpll_regs->cm_idlest_dpll) & ST_DPLL_CLK_MASK;
|
|
|
|
return lock;
|
|
}
|
|
|
|
const struct dpll_params *get_mpu_dpll_params(struct dplls const *dpll_data)
|
|
{
|
|
u32 sysclk_ind = get_sys_clk_index();
|
|
return &dpll_data->mpu[sysclk_ind];
|
|
}
|
|
|
|
const struct dpll_params *get_core_dpll_params(struct dplls const *dpll_data)
|
|
{
|
|
u32 sysclk_ind = get_sys_clk_index();
|
|
return &dpll_data->core[sysclk_ind];
|
|
}
|
|
|
|
const struct dpll_params *get_per_dpll_params(struct dplls const *dpll_data)
|
|
{
|
|
u32 sysclk_ind = get_sys_clk_index();
|
|
return &dpll_data->per[sysclk_ind];
|
|
}
|
|
|
|
const struct dpll_params *get_iva_dpll_params(struct dplls const *dpll_data)
|
|
{
|
|
u32 sysclk_ind = get_sys_clk_index();
|
|
return &dpll_data->iva[sysclk_ind];
|
|
}
|
|
|
|
const struct dpll_params *get_usb_dpll_params(struct dplls const *dpll_data)
|
|
{
|
|
u32 sysclk_ind = get_sys_clk_index();
|
|
return &dpll_data->usb[sysclk_ind];
|
|
}
|
|
|
|
const struct dpll_params *get_abe_dpll_params(struct dplls const *dpll_data)
|
|
{
|
|
#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
|
|
u32 sysclk_ind = get_sys_clk_index();
|
|
return &dpll_data->abe[sysclk_ind];
|
|
#else
|
|
return dpll_data->abe;
|
|
#endif
|
|
}
|
|
|
|
static const struct dpll_params *get_ddr_dpll_params
|
|
(struct dplls const *dpll_data)
|
|
{
|
|
u32 sysclk_ind = get_sys_clk_index();
|
|
|
|
if (!dpll_data->ddr)
|
|
return NULL;
|
|
return &dpll_data->ddr[sysclk_ind];
|
|
}
|
|
|
|
#ifdef CONFIG_DRIVER_TI_CPSW
|
|
static const struct dpll_params *get_gmac_dpll_params
|
|
(struct dplls const *dpll_data)
|
|
{
|
|
u32 sysclk_ind = get_sys_clk_index();
|
|
|
|
if (!dpll_data->gmac)
|
|
return NULL;
|
|
return &dpll_data->gmac[sysclk_ind];
|
|
}
|
|
#endif
|
|
|
|
static void do_setup_dpll(u32 const base, const struct dpll_params *params,
|
|
u8 lock, char *dpll)
|
|
{
|
|
u32 temp, M, N;
|
|
struct dpll_regs *const dpll_regs = (struct dpll_regs *)base;
|
|
|
|
if (!params)
|
|
return;
|
|
|
|
temp = readl(&dpll_regs->cm_clksel_dpll);
|
|
|
|
if (check_for_lock(base)) {
|
|
/*
|
|
* The Dpll has already been locked by rom code using CH.
|
|
* Check if M,N are matching with Ideal nominal opp values.
|
|
* If matches, skip the rest otherwise relock.
|
|
*/
|
|
M = (temp & CM_CLKSEL_DPLL_M_MASK) >> CM_CLKSEL_DPLL_M_SHIFT;
|
|
N = (temp & CM_CLKSEL_DPLL_N_MASK) >> CM_CLKSEL_DPLL_N_SHIFT;
|
|
if ((M != (params->m)) || (N != (params->n))) {
|
|
debug("\n %s Dpll locked, but not for ideal M = %d,"
|
|
"N = %d values, current values are M = %d,"
|
|
"N= %d" , dpll, params->m, params->n,
|
|
M, N);
|
|
} else {
|
|
/* Dpll locked with ideal values for nominal opps. */
|
|
debug("\n %s Dpll already locked with ideal"
|
|
"nominal opp values", dpll);
|
|
goto setup_post_dividers;
|
|
}
|
|
}
|
|
|
|
bypass_dpll(base);
|
|
|
|
/* Set M & N */
|
|
temp &= ~CM_CLKSEL_DPLL_M_MASK;
|
|
temp |= (params->m << CM_CLKSEL_DPLL_M_SHIFT) & CM_CLKSEL_DPLL_M_MASK;
|
|
|
|
temp &= ~CM_CLKSEL_DPLL_N_MASK;
|
|
temp |= (params->n << CM_CLKSEL_DPLL_N_SHIFT) & CM_CLKSEL_DPLL_N_MASK;
|
|
|
|
writel(temp, &dpll_regs->cm_clksel_dpll);
|
|
|
|
/* Lock */
|
|
if (lock)
|
|
do_lock_dpll(base);
|
|
|
|
setup_post_dividers:
|
|
setup_post_dividers(base, params);
|
|
|
|
/* Wait till the DPLL locks */
|
|
if (lock)
|
|
wait_for_lock(base);
|
|
}
|
|
|
|
u32 omap_ddr_clk(void)
|
|
{
|
|
u32 ddr_clk, sys_clk_khz, omap_rev, divider;
|
|
const struct dpll_params *core_dpll_params;
|
|
|
|
omap_rev = omap_revision();
|
|
sys_clk_khz = get_sys_clk_freq() / 1000;
|
|
|
|
core_dpll_params = get_core_dpll_params(*dplls_data);
|
|
|
|
debug("sys_clk %d\n ", sys_clk_khz * 1000);
|
|
|
|
/* Find Core DPLL locked frequency first */
|
|
ddr_clk = sys_clk_khz * 2 * core_dpll_params->m /
|
|
(core_dpll_params->n + 1);
|
|
|
|
if (omap_rev < OMAP5430_ES1_0) {
|
|
/*
|
|
* DDR frequency is PHY_ROOT_CLK/2
|
|
* PHY_ROOT_CLK = Fdpll/2/M2
|
|
*/
|
|
divider = 4;
|
|
} else {
|
|
/*
|
|
* DDR frequency is PHY_ROOT_CLK
|
|
* PHY_ROOT_CLK = Fdpll/2/M2
|
|
*/
|
|
divider = 2;
|
|
}
|
|
|
|
ddr_clk = ddr_clk / divider / core_dpll_params->m2;
|
|
ddr_clk *= 1000; /* convert to Hz */
|
|
debug("ddr_clk %d\n ", ddr_clk);
|
|
|
|
return ddr_clk;
|
|
}
|
|
|
|
/*
|
|
* Lock MPU dpll
|
|
*
|
|
* Resulting MPU frequencies:
|
|
* 4430 ES1.0 : 600 MHz
|
|
* 4430 ES2.x : 792 MHz (OPP Turbo)
|
|
* 4460 : 920 MHz (OPP Turbo) - DCC disabled
|
|
*/
|
|
void configure_mpu_dpll(void)
|
|
{
|
|
const struct dpll_params *params;
|
|
struct dpll_regs *mpu_dpll_regs;
|
|
u32 omap_rev;
|
|
omap_rev = omap_revision();
|
|
|
|
/*
|
|
* DCC and clock divider settings for 4460.
|
|
* DCC is required, if more than a certain frequency is required.
|
|
* For, 4460 > 1GHZ.
|
|
* 5430 > 1.4GHZ.
|
|
*/
|
|
if ((omap_rev >= OMAP4460_ES1_0) && (omap_rev < OMAP5430_ES1_0)) {
|
|
mpu_dpll_regs =
|
|
(struct dpll_regs *)((*prcm)->cm_clkmode_dpll_mpu);
|
|
bypass_dpll((*prcm)->cm_clkmode_dpll_mpu);
|
|
clrbits_le32((*prcm)->cm_mpu_mpu_clkctrl,
|
|
MPU_CLKCTRL_CLKSEL_EMIF_DIV_MODE_MASK);
|
|
setbits_le32((*prcm)->cm_mpu_mpu_clkctrl,
|
|
MPU_CLKCTRL_CLKSEL_ABE_DIV_MODE_MASK);
|
|
clrbits_le32(&mpu_dpll_regs->cm_clksel_dpll,
|
|
CM_CLKSEL_DCC_EN_MASK);
|
|
}
|
|
|
|
params = get_mpu_dpll_params(*dplls_data);
|
|
|
|
do_setup_dpll((*prcm)->cm_clkmode_dpll_mpu, params, DPLL_LOCK, "mpu");
|
|
debug("MPU DPLL locked\n");
|
|
}
|
|
|
|
#ifdef CONFIG_USB_EHCI_OMAP
|
|
static void setup_usb_dpll(void)
|
|
{
|
|
const struct dpll_params *params;
|
|
u32 sys_clk_khz, sd_div, num, den;
|
|
|
|
sys_clk_khz = get_sys_clk_freq() / 1000;
|
|
/*
|
|
* USB:
|
|
* USB dpll is J-type. Need to set DPLL_SD_DIV for jitter correction
|
|
* DPLL_SD_DIV = CEILING ([DPLL_MULT/(DPLL_DIV+1)]* CLKINP / 250)
|
|
* - where CLKINP is sys_clk in MHz
|
|
* Use CLKINP in KHz and adjust the denominator accordingly so
|
|
* that we have enough accuracy and at the same time no overflow
|
|
*/
|
|
params = get_usb_dpll_params(*dplls_data);
|
|
num = params->m * sys_clk_khz;
|
|
den = (params->n + 1) * 250 * 1000;
|
|
num += den - 1;
|
|
sd_div = num / den;
|
|
clrsetbits_le32((*prcm)->cm_clksel_dpll_usb,
|
|
CM_CLKSEL_DPLL_DPLL_SD_DIV_MASK,
|
|
sd_div << CM_CLKSEL_DPLL_DPLL_SD_DIV_SHIFT);
|
|
|
|
/* Now setup the dpll with the regular function */
|
|
do_setup_dpll((*prcm)->cm_clkmode_dpll_usb, params, DPLL_LOCK, "usb");
|
|
}
|
|
#endif
|
|
|
|
static void setup_dplls(void)
|
|
{
|
|
u32 temp;
|
|
const struct dpll_params *params;
|
|
|
|
debug("setup_dplls\n");
|
|
|
|
/* CORE dpll */
|
|
params = get_core_dpll_params(*dplls_data); /* default - safest */
|
|
/*
|
|
* Do not lock the core DPLL now. Just set it up.
|
|
* Core DPLL will be locked after setting up EMIF
|
|
* using the FREQ_UPDATE method(freq_update_core())
|
|
*/
|
|
if (emif_sdram_type() == EMIF_SDRAM_TYPE_LPDDR2)
|
|
do_setup_dpll((*prcm)->cm_clkmode_dpll_core, params,
|
|
DPLL_NO_LOCK, "core");
|
|
else
|
|
do_setup_dpll((*prcm)->cm_clkmode_dpll_core, params,
|
|
DPLL_LOCK, "core");
|
|
/* Set the ratios for CORE_CLK, L3_CLK, L4_CLK */
|
|
temp = (CLKSEL_CORE_X2_DIV_1 << CLKSEL_CORE_SHIFT) |
|
|
(CLKSEL_L3_CORE_DIV_2 << CLKSEL_L3_SHIFT) |
|
|
(CLKSEL_L4_L3_DIV_2 << CLKSEL_L4_SHIFT);
|
|
writel(temp, (*prcm)->cm_clksel_core);
|
|
debug("Core DPLL configured\n");
|
|
|
|
/* lock PER dpll */
|
|
params = get_per_dpll_params(*dplls_data);
|
|
do_setup_dpll((*prcm)->cm_clkmode_dpll_per,
|
|
params, DPLL_LOCK, "per");
|
|
debug("PER DPLL locked\n");
|
|
|
|
/* MPU dpll */
|
|
configure_mpu_dpll();
|
|
|
|
#ifdef CONFIG_USB_EHCI_OMAP
|
|
setup_usb_dpll();
|
|
#endif
|
|
params = get_ddr_dpll_params(*dplls_data);
|
|
do_setup_dpll((*prcm)->cm_clkmode_dpll_ddrphy,
|
|
params, DPLL_LOCK, "ddr");
|
|
|
|
#ifdef CONFIG_DRIVER_TI_CPSW
|
|
params = get_gmac_dpll_params(*dplls_data);
|
|
do_setup_dpll((*prcm)->cm_clkmode_dpll_gmac, params,
|
|
DPLL_LOCK, "gmac");
|
|
#endif
|
|
}
|
|
|
|
#ifdef CONFIG_SYS_CLOCKS_ENABLE_ALL
|
|
static void setup_non_essential_dplls(void)
|
|
{
|
|
u32 abe_ref_clk;
|
|
const struct dpll_params *params;
|
|
|
|
/* IVA */
|
|
clrsetbits_le32((*prcm)->cm_bypclk_dpll_iva,
|
|
CM_BYPCLK_DPLL_IVA_CLKSEL_MASK, DPLL_IVA_CLKSEL_CORE_X2_DIV_2);
|
|
|
|
params = get_iva_dpll_params(*dplls_data);
|
|
do_setup_dpll((*prcm)->cm_clkmode_dpll_iva, params, DPLL_LOCK, "iva");
|
|
|
|
/* Configure ABE dpll */
|
|
params = get_abe_dpll_params(*dplls_data);
|
|
#ifdef CONFIG_SYS_OMAP_ABE_SYSCK
|
|
abe_ref_clk = CM_ABE_PLL_REF_CLKSEL_CLKSEL_SYSCLK;
|
|
|
|
if (omap_revision() == DRA752_ES1_0)
|
|
/* Select the sys clk for dpll_abe */
|
|
clrsetbits_le32((*prcm)->cm_abe_pll_sys_clksel,
|
|
CM_CLKSEL_ABE_PLL_SYS_CLKSEL_MASK,
|
|
CM_ABE_PLL_SYS_CLKSEL_SYSCLK2);
|
|
#else
|
|
abe_ref_clk = CM_ABE_PLL_REF_CLKSEL_CLKSEL_32KCLK;
|
|
/*
|
|
* We need to enable some additional options to achieve
|
|
* 196.608MHz from 32768 Hz
|
|
*/
|
|
setbits_le32((*prcm)->cm_clkmode_dpll_abe,
|
|
CM_CLKMODE_DPLL_DRIFTGUARD_EN_MASK|
|
|
CM_CLKMODE_DPLL_RELOCK_RAMP_EN_MASK|
|
|
CM_CLKMODE_DPLL_LPMODE_EN_MASK|
|
|
CM_CLKMODE_DPLL_REGM4XEN_MASK);
|
|
/* Spend 4 REFCLK cycles at each stage */
|
|
clrsetbits_le32((*prcm)->cm_clkmode_dpll_abe,
|
|
CM_CLKMODE_DPLL_RAMP_RATE_MASK,
|
|
1 << CM_CLKMODE_DPLL_RAMP_RATE_SHIFT);
|
|
#endif
|
|
|
|
/* Select the right reference clk */
|
|
clrsetbits_le32((*prcm)->cm_abe_pll_ref_clksel,
|
|
CM_ABE_PLL_REF_CLKSEL_CLKSEL_MASK,
|
|
abe_ref_clk << CM_ABE_PLL_REF_CLKSEL_CLKSEL_SHIFT);
|
|
/* Lock the dpll */
|
|
do_setup_dpll((*prcm)->cm_clkmode_dpll_abe, params, DPLL_LOCK, "abe");
|
|
}
|
|
#endif
|
|
|
|
u32 get_offset_code(u32 volt_offset, struct pmic_data *pmic)
|
|
{
|
|
u32 offset_code;
|
|
|
|
volt_offset -= pmic->base_offset;
|
|
|
|
offset_code = (volt_offset + pmic->step - 1) / pmic->step;
|
|
|
|
/*
|
|
* Offset codes 1-6 all give the base voltage in Palmas
|
|
* Offset code 0 switches OFF the SMPS
|
|
*/
|
|
return offset_code + pmic->start_code;
|
|
}
|
|
|
|
void do_scale_vcore(u32 vcore_reg, u32 volt_mv, struct pmic_data *pmic)
|
|
{
|
|
u32 offset_code;
|
|
u32 offset = volt_mv;
|
|
int ret = 0;
|
|
|
|
if (!volt_mv)
|
|
return;
|
|
|
|
pmic->pmic_bus_init();
|
|
/* See if we can first get the GPIO if needed */
|
|
if (pmic->gpio_en)
|
|
ret = gpio_request(pmic->gpio, "PMIC_GPIO");
|
|
|
|
if (ret < 0) {
|
|
printf("%s: gpio %d request failed %d\n", __func__,
|
|
pmic->gpio, ret);
|
|
return;
|
|
}
|
|
|
|
/* Pull the GPIO low to select SET0 register, while we program SET1 */
|
|
if (pmic->gpio_en)
|
|
gpio_direction_output(pmic->gpio, 0);
|
|
|
|
/* convert to uV for better accuracy in the calculations */
|
|
offset *= 1000;
|
|
|
|
offset_code = get_offset_code(offset, pmic);
|
|
|
|
debug("do_scale_vcore: volt - %d offset_code - 0x%x\n", volt_mv,
|
|
offset_code);
|
|
|
|
if (pmic->pmic_write(pmic->i2c_slave_addr, vcore_reg, offset_code))
|
|
printf("Scaling voltage failed for 0x%x\n", vcore_reg);
|
|
|
|
if (pmic->gpio_en)
|
|
gpio_direction_output(pmic->gpio, 1);
|
|
}
|
|
|
|
static u32 optimize_vcore_voltage(struct volts const *v)
|
|
{
|
|
u32 val;
|
|
if (!v->value)
|
|
return 0;
|
|
if (!v->efuse.reg)
|
|
return v->value;
|
|
|
|
switch (v->efuse.reg_bits) {
|
|
case 16:
|
|
val = readw(v->efuse.reg);
|
|
break;
|
|
case 32:
|
|
val = readl(v->efuse.reg);
|
|
break;
|
|
default:
|
|
printf("Error: efuse 0x%08x bits=%d unknown\n",
|
|
v->efuse.reg, v->efuse.reg_bits);
|
|
return v->value;
|
|
}
|
|
|
|
if (!val) {
|
|
printf("Error: efuse 0x%08x bits=%d val=0, using %d\n",
|
|
v->efuse.reg, v->efuse.reg_bits, v->value);
|
|
return v->value;
|
|
}
|
|
|
|
debug("%s:efuse 0x%08x bits=%d Vnom=%d, using efuse value %d\n",
|
|
__func__, v->efuse.reg, v->efuse.reg_bits, v->value, val);
|
|
return val;
|
|
}
|
|
|
|
/*
|
|
* Setup the voltages for vdd_mpu, vdd_core, and vdd_iva
|
|
* We set the maximum voltages allowed here because Smart-Reflex is not
|
|
* enabled in bootloader. Voltage initialization in the kernel will set
|
|
* these to the nominal values after enabling Smart-Reflex
|
|
*/
|
|
void scale_vcores(struct vcores_data const *vcores)
|
|
{
|
|
u32 val;
|
|
|
|
val = optimize_vcore_voltage(&vcores->core);
|
|
do_scale_vcore(vcores->core.addr, val, vcores->core.pmic);
|
|
|
|
val = optimize_vcore_voltage(&vcores->mpu);
|
|
do_scale_vcore(vcores->mpu.addr, val, vcores->mpu.pmic);
|
|
|
|
/* Configure MPU ABB LDO after scale */
|
|
abb_setup((*ctrl)->control_std_fuse_opp_vdd_mpu_2,
|
|
(*ctrl)->control_wkup_ldovbb_mpu_voltage_ctrl,
|
|
(*prcm)->prm_abbldo_mpu_setup,
|
|
(*prcm)->prm_abbldo_mpu_ctrl,
|
|
(*prcm)->prm_irqstatus_mpu_2,
|
|
OMAP_ABB_MPU_TXDONE_MASK,
|
|
OMAP_ABB_FAST_OPP);
|
|
|
|
val = optimize_vcore_voltage(&vcores->mm);
|
|
do_scale_vcore(vcores->mm.addr, val, vcores->mm.pmic);
|
|
|
|
val = optimize_vcore_voltage(&vcores->gpu);
|
|
do_scale_vcore(vcores->gpu.addr, val, vcores->gpu.pmic);
|
|
|
|
val = optimize_vcore_voltage(&vcores->eve);
|
|
do_scale_vcore(vcores->eve.addr, val, vcores->eve.pmic);
|
|
|
|
val = optimize_vcore_voltage(&vcores->iva);
|
|
do_scale_vcore(vcores->iva.addr, val, vcores->iva.pmic);
|
|
}
|
|
|
|
static inline void enable_clock_domain(u32 const clkctrl_reg, u32 enable_mode)
|
|
{
|
|
clrsetbits_le32(clkctrl_reg, CD_CLKCTRL_CLKTRCTRL_MASK,
|
|
enable_mode << CD_CLKCTRL_CLKTRCTRL_SHIFT);
|
|
debug("Enable clock domain - %x\n", clkctrl_reg);
|
|
}
|
|
|
|
static inline void wait_for_clk_enable(u32 clkctrl_addr)
|
|
{
|
|
u32 clkctrl, idlest = MODULE_CLKCTRL_IDLEST_DISABLED;
|
|
u32 bound = LDELAY;
|
|
|
|
while ((idlest == MODULE_CLKCTRL_IDLEST_DISABLED) ||
|
|
(idlest == MODULE_CLKCTRL_IDLEST_TRANSITIONING)) {
|
|
|
|
clkctrl = readl(clkctrl_addr);
|
|
idlest = (clkctrl & MODULE_CLKCTRL_IDLEST_MASK) >>
|
|
MODULE_CLKCTRL_IDLEST_SHIFT;
|
|
if (--bound == 0) {
|
|
printf("Clock enable failed for 0x%x idlest 0x%x\n",
|
|
clkctrl_addr, clkctrl);
|
|
return;
|
|
}
|
|
}
|
|
}
|
|
|
|
static inline void enable_clock_module(u32 const clkctrl_addr, u32 enable_mode,
|
|
u32 wait_for_enable)
|
|
{
|
|
clrsetbits_le32(clkctrl_addr, MODULE_CLKCTRL_MODULEMODE_MASK,
|
|
enable_mode << MODULE_CLKCTRL_MODULEMODE_SHIFT);
|
|
debug("Enable clock module - %x\n", clkctrl_addr);
|
|
if (wait_for_enable)
|
|
wait_for_clk_enable(clkctrl_addr);
|
|
}
|
|
|
|
void freq_update_core(void)
|
|
{
|
|
u32 freq_config1 = 0;
|
|
const struct dpll_params *core_dpll_params;
|
|
u32 omap_rev = omap_revision();
|
|
|
|
core_dpll_params = get_core_dpll_params(*dplls_data);
|
|
/* Put EMIF clock domain in sw wakeup mode */
|
|
enable_clock_domain((*prcm)->cm_memif_clkstctrl,
|
|
CD_CLKCTRL_CLKTRCTRL_SW_WKUP);
|
|
wait_for_clk_enable((*prcm)->cm_memif_emif_1_clkctrl);
|
|
wait_for_clk_enable((*prcm)->cm_memif_emif_2_clkctrl);
|
|
|
|
freq_config1 = SHADOW_FREQ_CONFIG1_FREQ_UPDATE_MASK |
|
|
SHADOW_FREQ_CONFIG1_DLL_RESET_MASK;
|
|
|
|
freq_config1 |= (DPLL_EN_LOCK << SHADOW_FREQ_CONFIG1_DPLL_EN_SHIFT) &
|
|
SHADOW_FREQ_CONFIG1_DPLL_EN_MASK;
|
|
|
|
freq_config1 |= (core_dpll_params->m2 <<
|
|
SHADOW_FREQ_CONFIG1_M2_DIV_SHIFT) &
|
|
SHADOW_FREQ_CONFIG1_M2_DIV_MASK;
|
|
|
|
writel(freq_config1, (*prcm)->cm_shadow_freq_config1);
|
|
if (!wait_on_value(SHADOW_FREQ_CONFIG1_FREQ_UPDATE_MASK, 0,
|
|
(u32 *) (*prcm)->cm_shadow_freq_config1, LDELAY)) {
|
|
puts("FREQ UPDATE procedure failed!!");
|
|
hang();
|
|
}
|
|
|
|
/*
|
|
* Putting EMIF in HW_AUTO is seen to be causing issues with
|
|
* EMIF clocks and the master DLL. Keep EMIF in SW_WKUP
|
|
* in OMAP5430 ES1.0 silicon
|
|
*/
|
|
if (omap_rev != OMAP5430_ES1_0) {
|
|
/* Put EMIF clock domain back in hw auto mode */
|
|
enable_clock_domain((*prcm)->cm_memif_clkstctrl,
|
|
CD_CLKCTRL_CLKTRCTRL_HW_AUTO);
|
|
wait_for_clk_enable((*prcm)->cm_memif_emif_1_clkctrl);
|
|
wait_for_clk_enable((*prcm)->cm_memif_emif_2_clkctrl);
|
|
}
|
|
}
|
|
|
|
void bypass_dpll(u32 const base)
|
|
{
|
|
do_bypass_dpll(base);
|
|
wait_for_bypass(base);
|
|
}
|
|
|
|
void lock_dpll(u32 const base)
|
|
{
|
|
do_lock_dpll(base);
|
|
wait_for_lock(base);
|
|
}
|
|
|
|
void setup_clocks_for_console(void)
|
|
{
|
|
/* Do not add any spl_debug prints in this function */
|
|
clrsetbits_le32((*prcm)->cm_l4per_clkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK,
|
|
CD_CLKCTRL_CLKTRCTRL_SW_WKUP <<
|
|
CD_CLKCTRL_CLKTRCTRL_SHIFT);
|
|
|
|
/* Enable all UARTs - console will be on one of them */
|
|
clrsetbits_le32((*prcm)->cm_l4per_uart1_clkctrl,
|
|
MODULE_CLKCTRL_MODULEMODE_MASK,
|
|
MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
|
|
MODULE_CLKCTRL_MODULEMODE_SHIFT);
|
|
|
|
clrsetbits_le32((*prcm)->cm_l4per_uart2_clkctrl,
|
|
MODULE_CLKCTRL_MODULEMODE_MASK,
|
|
MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
|
|
MODULE_CLKCTRL_MODULEMODE_SHIFT);
|
|
|
|
clrsetbits_le32((*prcm)->cm_l4per_uart3_clkctrl,
|
|
MODULE_CLKCTRL_MODULEMODE_MASK,
|
|
MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
|
|
MODULE_CLKCTRL_MODULEMODE_SHIFT);
|
|
|
|
clrsetbits_le32((*prcm)->cm_l4per_uart4_clkctrl,
|
|
MODULE_CLKCTRL_MODULEMODE_MASK,
|
|
MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN <<
|
|
MODULE_CLKCTRL_MODULEMODE_SHIFT);
|
|
|
|
clrsetbits_le32((*prcm)->cm_l4per_clkstctrl, CD_CLKCTRL_CLKTRCTRL_MASK,
|
|
CD_CLKCTRL_CLKTRCTRL_HW_AUTO <<
|
|
CD_CLKCTRL_CLKTRCTRL_SHIFT);
|
|
}
|
|
|
|
void do_enable_clocks(u32 const *clk_domains,
|
|
u32 const *clk_modules_hw_auto,
|
|
u32 const *clk_modules_explicit_en,
|
|
u8 wait_for_enable)
|
|
{
|
|
u32 i, max = 100;
|
|
|
|
/* Put the clock domains in SW_WKUP mode */
|
|
for (i = 0; (i < max) && clk_domains[i]; i++) {
|
|
enable_clock_domain(clk_domains[i],
|
|
CD_CLKCTRL_CLKTRCTRL_SW_WKUP);
|
|
}
|
|
|
|
/* Clock modules that need to be put in HW_AUTO */
|
|
for (i = 0; (i < max) && clk_modules_hw_auto[i]; i++) {
|
|
enable_clock_module(clk_modules_hw_auto[i],
|
|
MODULE_CLKCTRL_MODULEMODE_HW_AUTO,
|
|
wait_for_enable);
|
|
};
|
|
|
|
/* Clock modules that need to be put in SW_EXPLICIT_EN mode */
|
|
for (i = 0; (i < max) && clk_modules_explicit_en[i]; i++) {
|
|
enable_clock_module(clk_modules_explicit_en[i],
|
|
MODULE_CLKCTRL_MODULEMODE_SW_EXPLICIT_EN,
|
|
wait_for_enable);
|
|
};
|
|
|
|
/* Put the clock domains in HW_AUTO mode now */
|
|
for (i = 0; (i < max) && clk_domains[i]; i++) {
|
|
enable_clock_domain(clk_domains[i],
|
|
CD_CLKCTRL_CLKTRCTRL_HW_AUTO);
|
|
}
|
|
}
|
|
|
|
void prcm_init(void)
|
|
{
|
|
switch (omap_hw_init_context()) {
|
|
case OMAP_INIT_CONTEXT_SPL:
|
|
case OMAP_INIT_CONTEXT_UBOOT_FROM_NOR:
|
|
case OMAP_INIT_CONTEXT_UBOOT_AFTER_CH:
|
|
enable_basic_clocks();
|
|
timer_init();
|
|
scale_vcores(*omap_vcores);
|
|
setup_dplls();
|
|
#ifdef CONFIG_SYS_CLOCKS_ENABLE_ALL
|
|
setup_non_essential_dplls();
|
|
enable_non_essential_clocks();
|
|
#endif
|
|
setup_warmreset_time();
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
|
|
if (OMAP_INIT_CONTEXT_SPL != omap_hw_init_context())
|
|
enable_basic_uboot_clocks();
|
|
}
|
|
|
|
void gpi2c_init(void)
|
|
{
|
|
static int gpi2c = 1;
|
|
|
|
if (gpi2c) {
|
|
i2c_init(CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE);
|
|
gpi2c = 0;
|
|
}
|
|
}
|