mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-07 05:34:28 +00:00
a09fea1d28
- In ARMv8 NXP Layerscape platforms we also need to make use of CONFIG_SYS_RELOC_GD_ENV_ADDR now, do so. - On ENV_IS_IN_REMOTE, CONFIG_ENV_OFFSET is never used, drop the define to 0. - Add Kconfig entry for ENV_ADDR. - Make ENV_ADDR / ENV_OFFSET depend on the env locations that use it. - Add ENV_xxx_REDUND options that depend on their primary option and SYS_REDUNDAND_ENVIRONMENT - On a number of PowerPC platforms, use SPL_ENV_ADDR not CONFIG_ENV_ADDR for the pre-main-U-Boot environment location. - On ENV_IS_IN_SPI_FLASH, check not for CONFIG_ENV_ADDR being set but rather it being non-zero, as it will now be zero by default. - Rework the env_offset absolute in env/embedded.o to not use CONFIG_ENV_OFFSET as it was the only use of ENV_OFFSET within ENV_IS_IN_FLASH. - Migrate all platforms. Cc: Wolfgang Denk <wd@denx.de> Cc: Joe Hershberger <joe.hershberger@ni.com> Cc: Patrick Delaunay <patrick.delaunay@st.com> Cc: uboot-stm32@st-md-mailman.stormreply.com Signed-off-by: Tom Rini <trini@konsulko.com> Acked-by: Joe Hershberger <joe.hershberger@ni.com> Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
149 lines
4.1 KiB
C
149 lines
4.1 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Config file for Compulab CM-T335 board
|
|
*
|
|
* Copyright (C) 2013, Compulab Ltd - http://compulab.co.il/
|
|
*
|
|
* Author: Ilya Ledvich <ilya@compulab.co.il>
|
|
*/
|
|
|
|
#ifndef __CONFIG_CM_T335_H
|
|
#define __CONFIG_CM_T335_H
|
|
|
|
#define CONFIG_CM_T335
|
|
|
|
#include <configs/ti_am335x_common.h>
|
|
|
|
#undef CONFIG_MAX_RAM_BANK_SIZE
|
|
#define CONFIG_MAX_RAM_BANK_SIZE (512 << 20) /* 512MB */
|
|
|
|
#define CONFIG_MACH_TYPE MACH_TYPE_CM_T335
|
|
|
|
/* Clock Defines */
|
|
#define V_OSCK 25000000 /* Clock output from T2 */
|
|
#define V_SCLK (V_OSCK)
|
|
|
|
#ifndef CONFIG_SPL_BUILD
|
|
#define MMCARGS \
|
|
"mmcdev=0\0" \
|
|
"mmcroot=/dev/mmcblk0p2 rw rootwait\0" \
|
|
"mmcrootfstype=ext4\0" \
|
|
"mmcargs=setenv bootargs console=${console} " \
|
|
"root=${mmcroot} " \
|
|
"rootfstype=${mmcrootfstype}\0" \
|
|
"mmcboot=echo Booting from mmc ...; " \
|
|
"run mmcargs; " \
|
|
"bootm ${loadaddr}\0"
|
|
|
|
#define NANDARGS \
|
|
"mtdids=" CONFIG_MTDIDS_DEFAULT "\0" \
|
|
"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
|
|
"nandroot=ubi0:rootfs rw\0" \
|
|
"nandrootfstype=ubifs\0" \
|
|
"nandargs=setenv bootargs console=${console} " \
|
|
"root=${nandroot} " \
|
|
"rootfstype=${nandrootfstype} " \
|
|
"ubi.mtd=${rootfs_name}\0" \
|
|
"nandboot=echo Booting from nand ...; " \
|
|
"run nandargs; " \
|
|
"nboot ${loadaddr} nand0 900000; " \
|
|
"bootm ${loadaddr}\0"
|
|
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"loadaddr=82000000\0" \
|
|
"console=ttyO0,115200n8\0" \
|
|
"rootfs_name=rootfs\0" \
|
|
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
|
|
"bootscript=echo Running bootscript from mmc ...; " \
|
|
"source ${loadaddr}\0" \
|
|
"loaduimage=fatload mmc ${mmcdev} ${loadaddr} uImage\0" \
|
|
MMCARGS \
|
|
NANDARGS
|
|
|
|
#define CONFIG_BOOTCOMMAND \
|
|
"mmc dev ${mmcdev}; if mmc rescan; then " \
|
|
"if run loadbootscript; then " \
|
|
"run bootscript; " \
|
|
"else " \
|
|
"if run loaduimage; then " \
|
|
"run mmcboot; " \
|
|
"else run nandboot; " \
|
|
"fi; " \
|
|
"fi; " \
|
|
"else run nandboot; fi"
|
|
#endif /* CONFIG_SPL_BUILD */
|
|
|
|
#define CONFIG_TIMESTAMP
|
|
#define CONFIG_SYS_AUTOLOAD "no"
|
|
|
|
/* Serial console configuration */
|
|
|
|
/* NS16550 Configuration */
|
|
#define CONFIG_SYS_NS16550_COM1 0x44e09000 /* UART0 */
|
|
#define CONFIG_SYS_NS16550_COM2 0x48022000 /* UART1 */
|
|
|
|
/* I2C Configuration */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* Main EEPROM */
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_I2C_EEPROM_BUS 0
|
|
|
|
/* SPL */
|
|
|
|
/* Network. */
|
|
#define CONFIG_PHY_ATHEROS
|
|
|
|
/* NAND support */
|
|
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
|
|
#define CONFIG_SYS_NAND_PAGE_COUNT (CONFIG_SYS_NAND_BLOCK_SIZE / \
|
|
CONFIG_SYS_NAND_PAGE_SIZE)
|
|
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
|
|
#define CONFIG_SYS_NAND_OOBSIZE 64
|
|
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
|
|
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
|
|
#define CONFIG_SYS_NAND_ECCPOS { 2, 3, 4, 5, 6, 7, 8, 9, \
|
|
10, 11, 12, 13, 14, 15, 16, 17, \
|
|
18, 19, 20, 21, 22, 23, 24, 25, \
|
|
26, 27, 28, 29, 30, 31, 32, 33, \
|
|
34, 35, 36, 37, 38, 39, 40, 41, \
|
|
42, 43, 44, 45, 46, 47, 48, 49, \
|
|
50, 51, 52, 53, 54, 55, 56, 57, }
|
|
|
|
#define CONFIG_SYS_NAND_ECCSIZE 512
|
|
#define CONFIG_SYS_NAND_ECCBYTES 14
|
|
|
|
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_TEXT_BASE
|
|
|
|
#undef CONFIG_SYS_NAND_U_BOOT_OFFS
|
|
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x200000
|
|
|
|
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
|
|
#define CONFIG_SYS_NAND_ONFI_DETECTION
|
|
#ifdef CONFIG_SPL_OS_BOOT
|
|
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x500000
|
|
#endif
|
|
|
|
/* GPIO pin + bank to pin ID mapping */
|
|
#define GPIO_PIN(_bank, _pin) ((_bank << 5) + _pin)
|
|
|
|
/* Status LED */
|
|
/* Status LED polarity is inversed, so init it in the "off" state */
|
|
|
|
/* EEPROM */
|
|
#define CONFIG_ENV_EEPROM_IS_ON_I2C
|
|
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4
|
|
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
|
|
#define CONFIG_SYS_EEPROM_SIZE 256
|
|
|
|
#ifndef CONFIG_SPL_BUILD
|
|
/*
|
|
* Enable PCA9555 at I2C0-0x26.
|
|
* First select the I2C0 bus with "i2c dev 0", then use "pca953x" command.
|
|
*/
|
|
#define CONFIG_PCA953X
|
|
#define CONFIG_SYS_I2C_PCA953X_ADDR 0x26
|
|
#define CONFIG_SYS_I2C_PCA953X_WIDTH { {0x26, 16} }
|
|
#endif /* CONFIG_SPL_BUILD */
|
|
|
|
#endif /* __CONFIG_CM_T335_H */
|
|
|