mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-14 08:57:58 +00:00
6b66d2ee47
If UHS speed modes are enabled, a compatible SD card switches down to 1.8V during enumeration. If after this a software reboot/crash takes place and on-chip ROM tries to enumerate the SD card, the difference in IO voltages (host @ 3.3V and card @ 1.8V) may end up damaging the card. The fix for this is to have support for power cycling the card in hardware (with a PORz/soft-reset line causing a power cycle of the card). Because the beaglebone X15 (rev A,B and C), am57xx-evms and am57xx-idks don't have this capability, disable voltage switching for these boards. The major effect of this is that the maximum supported speed mode is now high speed(50 MHz) down from SDR104(200 MHz). Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
115 lines
2.3 KiB
Text
115 lines
2.3 KiB
Text
/*
|
|
* Copyright (C) 2015-2016 Texas Instruments Incorporated - http://www.ti.com/
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*/
|
|
/dts-v1/;
|
|
|
|
#include "dra72x.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include "am57xx-idk-common.dtsi"
|
|
#include "dra7-mmc-iodelay.dtsi"
|
|
#include "dra72x-mmc-iodelay.dtsi"
|
|
|
|
/ {
|
|
model = "TI AM5718 IDK";
|
|
compatible = "ti,am5718-idk", "ti,am5718", "ti,dra7";
|
|
|
|
memory@80000000 {
|
|
device_type = "memory";
|
|
reg = <0x0 0x80000000 0x0 0x40000000>;
|
|
};
|
|
|
|
leds {
|
|
compatible = "gpio-leds";
|
|
cpu0-led {
|
|
label = "status0:red:cpu0";
|
|
gpios = <&gpio2 25 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
linux,default-trigger = "cpu0";
|
|
};
|
|
|
|
usr0-led {
|
|
label = "status0:green:usr";
|
|
gpios = <&gpio2 26 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
|
|
heartbeat-led {
|
|
label = "status0:blue:heartbeat";
|
|
gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
linux,default-trigger = "heartbeat";
|
|
};
|
|
|
|
usr1-led {
|
|
label = "status1:red:usr";
|
|
gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
|
|
usr2-led {
|
|
label = "status1:green:usr";
|
|
gpios = <&gpio2 21 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
};
|
|
|
|
mmc0-led {
|
|
label = "status1:blue:mmc0";
|
|
gpios = <&gpio2 19 GPIO_ACTIVE_HIGH>;
|
|
default-state = "off";
|
|
linux,default-trigger = "mmc0";
|
|
};
|
|
};
|
|
};
|
|
|
|
&omap_dwc3_2 {
|
|
extcon = <&extcon_usb2>;
|
|
};
|
|
|
|
&extcon_usb2 {
|
|
id-gpio = <&gpio5 7 GPIO_ACTIVE_HIGH>;
|
|
vbus-gpio = <&gpio7 22 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
&mailbox5 {
|
|
status = "okay";
|
|
mbox_ipu1_ipc3x: mbox_ipu1_ipc3x {
|
|
status = "okay";
|
|
};
|
|
mbox_dsp1_ipc3x: mbox_dsp1_ipc3x {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&mailbox6 {
|
|
status = "okay";
|
|
mbox_ipu2_ipc3x: mbox_ipu2_ipc3x {
|
|
status = "okay";
|
|
};
|
|
};
|
|
|
|
&pcie1_rc {
|
|
status = "okay";
|
|
gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
&pcie1_ep {
|
|
gpios = <&gpio3 23 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
&mmc1 {
|
|
pinctrl-names = "default", "hs";
|
|
pinctrl-0 = <&mmc1_pins_default_no_clk_pu>;
|
|
pinctrl-1 = <&mmc1_pins_hs>;
|
|
};
|
|
|
|
&mmc2 {
|
|
pinctrl-names = "default", "hs", "ddr_1_8v";
|
|
pinctrl-0 = <&mmc2_pins_default>;
|
|
pinctrl-1 = <&mmc2_pins_hs>;
|
|
pinctrl-2 = <&mmc2_pins_ddr_rev20 &mmc2_iodelay_ddr_conf>;
|
|
};
|