mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-25 12:33:41 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
158 lines
3.1 KiB
C
158 lines
3.1 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
|
|
#include <common.h>
|
|
#include <cpu_func.h>
|
|
#include <hang.h>
|
|
#include <init.h>
|
|
#include <log.h>
|
|
#include <spl.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/io.h>
|
|
#include <asm/mach-imx/iomux-v3.h>
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/imx8mm_pins.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/mach-imx/boot_mode.h>
|
|
#include <asm/arch/ddr.h>
|
|
|
|
#include <dm/uclass.h>
|
|
#include <dm/device.h>
|
|
#include <dm/uclass-internal.h>
|
|
#include <dm/device-internal.h>
|
|
|
|
#include <power/pmic.h>
|
|
#include <power/bd71837.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int spl_board_boot_device(enum boot_device boot_dev_spl)
|
|
{
|
|
switch (boot_dev_spl) {
|
|
case SD2_BOOT:
|
|
case MMC2_BOOT:
|
|
return BOOT_DEVICE_MMC1;
|
|
case SD3_BOOT:
|
|
case MMC3_BOOT:
|
|
return BOOT_DEVICE_MMC2;
|
|
default:
|
|
return BOOT_DEVICE_NONE;
|
|
}
|
|
}
|
|
|
|
static void spl_dram_init(void)
|
|
{
|
|
ddr_init(&dram_timing);
|
|
}
|
|
|
|
void spl_board_init(void)
|
|
{
|
|
debug("Normal Boot\n");
|
|
}
|
|
|
|
#ifdef CONFIG_SPL_LOAD_FIT
|
|
int board_fit_config_name_match(const char *name)
|
|
{
|
|
/* Just empty function now - can't decide what to choose */
|
|
debug("%s: %s\n", __func__, name);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_FSEL1)
|
|
#define WDOG_PAD_CTRL (PAD_CTL_DSE6 | PAD_CTL_ODE | PAD_CTL_PUE | PAD_CTL_PE)
|
|
|
|
static iomux_v3_cfg_t const uart_pads[] = {
|
|
IMX8MM_PAD_UART2_RXD_UART2_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
IMX8MM_PAD_UART2_TXD_UART2_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const wdog_pads[] = {
|
|
IMX8MM_PAD_GPIO1_IO02_WDOG1_WDOG_B | MUX_PAD_CTRL(WDOG_PAD_CTRL),
|
|
};
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
|
|
|
|
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
|
|
|
|
set_wdog_reset(wdog);
|
|
|
|
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int power_init_board(void)
|
|
{
|
|
struct udevice *dev;
|
|
int ret;
|
|
|
|
ret = pmic_get("pmic@4b", &dev);
|
|
if (ret == -ENODEV) {
|
|
puts("No pmic\n");
|
|
return 0;
|
|
}
|
|
if (ret != 0)
|
|
return ret;
|
|
|
|
/* decrease RESET key long push time from the default 10s to 10ms */
|
|
pmic_reg_write(dev, BD718XX_PWRONCONFIG1, 0x0);
|
|
|
|
/* unlock the PMIC regs */
|
|
pmic_reg_write(dev, BD718XX_REGLOCK, 0x1);
|
|
|
|
/* increase VDD_SOC to typical value 0.85v before first DRAM access */
|
|
pmic_reg_write(dev, BD718XX_BUCK1_VOLT_RUN, 0x0f);
|
|
|
|
/* increase VDD_DRAM to 0.975v for 3Ghz DDR */
|
|
pmic_reg_write(dev, BD718XX_1ST_NODVS_BUCK_VOLT, 0x83);
|
|
|
|
/* lock the PMIC regs */
|
|
pmic_reg_write(dev, BD718XX_REGLOCK, 0x11);
|
|
|
|
return 0;
|
|
}
|
|
|
|
void board_init_f(ulong dummy)
|
|
{
|
|
struct udevice *dev;
|
|
int ret;
|
|
|
|
arch_cpu_init();
|
|
|
|
init_uart_clk(1);
|
|
|
|
board_early_init_f();
|
|
|
|
timer_init();
|
|
|
|
preloader_console_init();
|
|
|
|
/* Clear the BSS. */
|
|
memset(__bss_start, 0, __bss_end - __bss_start);
|
|
|
|
ret = spl_early_init();
|
|
if (ret) {
|
|
debug("spl_early_init() failed: %d\n", ret);
|
|
hang();
|
|
}
|
|
|
|
ret = uclass_get_device_by_name(UCLASS_CLK,
|
|
"clock-controller@30380000",
|
|
&dev);
|
|
if (ret < 0) {
|
|
printf("Failed to find clock node. Check device tree\n");
|
|
hang();
|
|
}
|
|
|
|
enable_tzc380();
|
|
|
|
power_init_board();
|
|
|
|
/* DDR initialization */
|
|
spl_dram_init();
|
|
|
|
board_init_r(NULL, 0);
|
|
}
|