mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-07 13:44:29 +00:00
f41e588c03
This patch adds support for gmiitorgmii converter. This converter sits between the MAC and the external phy MAC <==> GMII2RGMII <==> RGMII_PHY. The ethernet driver probes this bridge and this bridge driver probes real phy driver and invokes the real phy functionalities as requested. This bridge just needs to be configured based on real phy negotiated speed and duplex. Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com>
248 lines
7 KiB
Text
248 lines
7 KiB
Text
|
|
config BITBANGMII
|
|
bool "Bit-banged ethernet MII management channel support"
|
|
|
|
config MV88E6352_SWITCH
|
|
bool "Marvell 88E6352 switch support"
|
|
|
|
menuconfig PHYLIB
|
|
bool "Ethernet PHY (physical media interface) support"
|
|
depends on NET
|
|
help
|
|
Enable Ethernet PHY (physical media interface) support.
|
|
|
|
if PHYLIB
|
|
|
|
config PHY_ADDR_ENABLE
|
|
bool "Limit phy address"
|
|
default y if ARCH_SUNXI
|
|
help
|
|
Select this if you want to control which phy address is used
|
|
|
|
if PHY_ADDR_ENABLE
|
|
config PHY_ADDR
|
|
int "PHY address"
|
|
default 1 if ARCH_SUNXI
|
|
default 0
|
|
help
|
|
The address of PHY on MII bus. Usually in range of 0 to 31.
|
|
endif
|
|
|
|
config B53_SWITCH
|
|
bool "Broadcom BCM53xx (RoboSwitch) Ethernet switch PHY support."
|
|
help
|
|
Enable support for Broadcom BCM53xx (RoboSwitch) Ethernet switches.
|
|
This currently supports BCM53125 and similar models.
|
|
|
|
if B53_SWITCH
|
|
|
|
config B53_CPU_PORT
|
|
int "CPU port"
|
|
default 8
|
|
|
|
config B53_PHY_PORTS
|
|
hex "Bitmask of PHY ports"
|
|
|
|
endif # B53_SWITCH
|
|
|
|
config MV88E61XX_SWITCH
|
|
bool "Marvel MV88E61xx Ethernet switch PHY support."
|
|
|
|
if MV88E61XX_SWITCH
|
|
|
|
config MV88E61XX_CPU_PORT
|
|
int "CPU Port"
|
|
|
|
config MV88E61XX_PHY_PORTS
|
|
hex "Bitmask of PHY Ports"
|
|
|
|
config MV88E61XX_FIXED_PORTS
|
|
hex "Bitmask of PHYless serdes Ports"
|
|
|
|
endif # MV88E61XX_SWITCH
|
|
|
|
config PHYLIB_10G
|
|
bool "Generic 10G PHY support"
|
|
|
|
menuconfig PHY_AQUANTIA
|
|
bool "Aquantia Ethernet PHYs support"
|
|
select PHY_GIGE
|
|
select PHYLIB_10G
|
|
|
|
config PHY_AQUANTIA_UPLOAD_FW
|
|
bool "Aquantia firmware loading support"
|
|
default n
|
|
depends on PHY_AQUANTIA
|
|
help
|
|
Aquantia PHYs use firmware which can be either loaded automatically
|
|
from storage directly attached to the phy or loaded by the boot loader
|
|
via MDIO commands. The firmware is loaded from a file, specified by
|
|
the PHY_AQUANTIA_FW_PART and PHY_AQUANTIA_FW_NAME options.
|
|
|
|
config PHY_AQUANTIA_FW_PART
|
|
string "Aquantia firmware partition"
|
|
depends on PHY_AQUANTIA_UPLOAD_FW
|
|
help
|
|
Partition containing the firmware file.
|
|
|
|
config PHY_AQUANTIA_FW_NAME
|
|
string "Aquantia firmware filename"
|
|
depends on PHY_AQUANTIA_UPLOAD_FW
|
|
help
|
|
Firmware filename.
|
|
|
|
config PHY_ATHEROS
|
|
bool "Atheros Ethernet PHYs support"
|
|
|
|
config PHY_BROADCOM
|
|
bool "Broadcom Ethernet PHYs support"
|
|
|
|
config PHY_CORTINA
|
|
bool "Cortina Ethernet PHYs support"
|
|
|
|
config PHY_DAVICOM
|
|
bool "Davicom Ethernet PHYs support"
|
|
|
|
config PHY_ET1011C
|
|
bool "LSI TruePHY ET1011C support"
|
|
|
|
config PHY_LXT
|
|
bool "LXT971 Ethernet PHY support"
|
|
|
|
config PHY_MARVELL
|
|
bool "Marvell Ethernet PHYs support"
|
|
|
|
config PHY_MESON_GXL
|
|
bool "Amlogic Meson GXL Internal PHY support"
|
|
|
|
config PHY_MICREL
|
|
bool "Micrel Ethernet PHYs support"
|
|
help
|
|
Enable support for the GbE PHYs manufactured by Micrel (now
|
|
a part of Microchip). This includes drivers for the KSZ804, KSZ8031,
|
|
KSZ8051, KSZ8081, KSZ8895, KSZ886x and KSZ8721 (if "Micrel KSZ8xxx
|
|
family support" is selected) and the KSZ9021 and KSZ9031 (if "Micrel
|
|
KSZ90x1 family support" is selected).
|
|
|
|
if PHY_MICREL
|
|
|
|
config PHY_MICREL_KSZ9021
|
|
bool
|
|
select PHY_MICREL_KSZ90X1
|
|
|
|
config PHY_MICREL_KSZ9031
|
|
bool
|
|
select PHY_MICREL_KSZ90X1
|
|
|
|
config PHY_MICREL_KSZ90X1
|
|
bool "Micrel KSZ90x1 family support"
|
|
select PHY_GIGE
|
|
help
|
|
Enable support for the Micrel KSZ9021 and KSZ9031 GbE PHYs. If
|
|
enabled, the extended register read/write for KSZ90x1 PHYs
|
|
is supported through the 'mdio' command and any RGMII signal
|
|
delays configured in the device tree will be applied to the
|
|
PHY during initialization.
|
|
|
|
config PHY_MICREL_KSZ8XXX
|
|
bool "Micrel KSZ8xxx family support"
|
|
help
|
|
Enable support for the 8000 series 10/100 PHYs manufactured by Micrel
|
|
(now a part of Microchip). This includes drivers for the KSZ804,
|
|
KSZ8031, KSZ8051, KSZ8081, KSZ8895, KSZ886x, and KSZ8721.
|
|
|
|
endif # PHY_MICREL
|
|
|
|
config PHY_MSCC
|
|
bool "Microsemi Corp Ethernet PHYs support"
|
|
|
|
config PHY_NATSEMI
|
|
bool "National Semiconductor Ethernet PHYs support"
|
|
|
|
config PHY_REALTEK
|
|
bool "Realtek Ethernet PHYs support"
|
|
|
|
config RTL8211E_PINE64_GIGABIT_FIX
|
|
bool "Fix gigabit throughput on some Pine64+ models"
|
|
depends on PHY_REALTEK
|
|
help
|
|
Configure the Realtek RTL8211E found on some Pine64+ models differently to
|
|
fix throughput on Gigabit links, turning off all internal delays in the
|
|
process. The settings that this touches are not documented in the CONFREG
|
|
section of the RTL8211E datasheet, but come from Realtek by way of the
|
|
Pine64 engineering team.
|
|
|
|
config RTL8211X_PHY_FORCE_MASTER
|
|
bool "Ethernet PHY RTL8211x: force 1000BASE-T master mode"
|
|
depends on PHY_REALTEK
|
|
help
|
|
Force master mode for 1000BASE-T on RTl8211x PHYs (except for RTL8211F).
|
|
This can work around link stability and data corruption issues on gigabit
|
|
links which can occur in slave mode on certain PHYs, e.g. on the
|
|
RTL8211C(L).
|
|
|
|
Please note that two directly connected devices (i.e. via crossover cable)
|
|
will not be able to establish a link between each other if they both force
|
|
master mode. Multiple devices forcing master mode when connected by a
|
|
network switch do not pose a problem as the switch configures its affected
|
|
ports into slave mode.
|
|
|
|
This option only affects gigabit links. If you must establish a direct
|
|
connection between two devices which both force master mode, try forcing
|
|
the link speed to 100MBit/s.
|
|
|
|
If unsure, say N.
|
|
|
|
config RTL8211F_PHY_FORCE_EEE_RXC_ON
|
|
bool "Ethernet PHY RTL8211F: do not stop receiving the xMII clock during LPI"
|
|
depends on PHY_REALTEK
|
|
default n
|
|
help
|
|
The IEEE 802.3az-2010 (EEE) standard provides a protocol to coordinate
|
|
transitions to/from a lower power consumption level (Low Power Idle
|
|
mode) based on link utilization. When no packets are being
|
|
transmitted, the system goes to Low Power Idle mode to save power.
|
|
|
|
Under particular circumstances this setting can cause issues where
|
|
the PHY is unable to transmit or receive any packet when in LPI mode.
|
|
The problem is caused when the PHY is configured to stop receiving
|
|
the xMII clock while it is signaling LPI. For some PHYs the bit
|
|
configuring this behavior is set by the Linux kernel, causing the
|
|
issue in U-Boot on reboot if the PHY retains the register value.
|
|
|
|
Default n, which means that the PHY state is not changed. To work
|
|
around the issues, change this setting to y.
|
|
|
|
config PHY_SMSC
|
|
bool "Microchip(SMSC) Ethernet PHYs support"
|
|
|
|
config PHY_TERANETICS
|
|
bool "Teranetics Ethernet PHYs support"
|
|
|
|
config PHY_TI
|
|
bool "Texas Instruments Ethernet PHYs support"
|
|
|
|
config PHY_VITESSE
|
|
bool "Vitesse Ethernet PHYs support"
|
|
|
|
config PHY_XILINX
|
|
bool "Xilinx Ethernet PHYs support"
|
|
|
|
config PHY_XILINX_GMII2RGMII
|
|
bool "Xilinx GMII to RGMII Ethernet PHYs support"
|
|
help
|
|
This adds support for Xilinx GMII to RGMII IP core. This IP acts
|
|
as bridge between MAC connected over GMII and external phy that
|
|
is connected over RGMII interface.
|
|
|
|
config PHY_FIXED
|
|
bool "Fixed-Link PHY"
|
|
depends on DM_ETH
|
|
help
|
|
Fixed PHY is used for having a 'fixed-link' to another MAC with a direct
|
|
connection (MII, RGMII, ...).
|
|
There is nothing like autoneogation and so
|
|
on, the link is always up with fixed speed and fixed duplex-setting.
|
|
More information: doc/device-tree-bindings/net/fixed-link.txt
|
|
|
|
endif #PHYLIB
|