u-boot/board/freescale/mx51evk/mx51evk.c
Fabio Estevam 07fc671d7e mx51evk: Convert to driver model
Make the conversion to driver model as it is mandatory.

Tested booting the Linux kernel from the SD card.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
2021-03-01 10:21:36 +01:00

218 lines
5.3 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2009 Freescale Semiconductor, Inc.
*/
#include <common.h>
#include <init.h>
#include <asm/global_data.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux-mx51.h>
#include <linux/delay.h>
#include <linux/errno.h>
#include <asm/arch/sys_proto.h>
#include <asm/arch/crm_regs.h>
#include <asm/arch/clock.h>
#include <asm/mach-imx/mx5_video.h>
#include <i2c.h>
#include <input.h>
#include <mmc.h>
#include <fsl_esdhc_imx.h>
#include <power/pmic.h>
#include <fsl_pmic.h>
#include <mc13892.h>
#include <usb/ehci-ci.h>
DECLARE_GLOBAL_DATA_PTR;
int dram_init(void)
{
/* dram_init must store complete ramsize in gd->ram_size */
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
PHYS_SDRAM_1_SIZE);
return 0;
}
u32 get_board_rev(void)
{
u32 rev = get_cpu_rev();
if (!gpio_get_value(IMX_GPIO_NR(1, 22)))
rev |= BOARD_REV_2_0 << BOARD_VER_OFFSET;
return rev;
}
#define UART_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_DOWN | PAD_CTL_DSE_HIGH)
static void setup_iomux_uart(void)
{
static const iomux_v3_cfg_t uart_pads[] = {
MX51_PAD_UART1_RXD__UART1_RXD,
MX51_PAD_UART1_TXD__UART1_TXD,
NEW_PAD_CTRL(MX51_PAD_UART1_RTS__UART1_RTS, UART_PAD_CTRL),
NEW_PAD_CTRL(MX51_PAD_UART1_CTS__UART1_CTS, UART_PAD_CTRL),
};
imx_iomux_v3_setup_multiple_pads(uart_pads, ARRAY_SIZE(uart_pads));
}
#ifdef CONFIG_MXC_SPI
static void setup_iomux_spi(void)
{
static const iomux_v3_cfg_t spi_pads[] = {
NEW_PAD_CTRL(MX51_PAD_CSPI1_MOSI__ECSPI1_MOSI, PAD_CTL_HYS |
PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_CSPI1_MISO__ECSPI1_MISO, PAD_CTL_HYS |
PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
NEW_PAD_CTRL(MX51_PAD_CSPI1_SS1__ECSPI1_SS1,
MX51_GPIO_PAD_CTRL),
MX51_PAD_CSPI1_SS0__ECSPI1_SS0,
NEW_PAD_CTRL(MX51_PAD_CSPI1_RDY__ECSPI1_RDY, MX51_PAD_CTRL_2),
NEW_PAD_CTRL(MX51_PAD_CSPI1_SCLK__ECSPI1_SCLK, PAD_CTL_HYS |
PAD_CTL_DSE_HIGH | PAD_CTL_SRE_FAST),
};
imx_iomux_v3_setup_multiple_pads(spi_pads, ARRAY_SIZE(spi_pads));
}
#endif
static void power_init(void)
{
unsigned int val;
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)MXC_CCM_BASE;
struct pmic *p;
int ret;
ret = pmic_init(CONFIG_FSL_PMIC_BUS);
if (ret)
return;
p = pmic_get("FSL_PMIC");
if (!p)
return;
/* Write needed to Power Gate 2 register */
pmic_reg_read(p, REG_POWER_MISC, &val);
val &= ~PWGT2SPIEN;
pmic_reg_write(p, REG_POWER_MISC, val);
/* Externally powered */
pmic_reg_read(p, REG_CHARGE, &val);
val |= ICHRG0 | ICHRG1 | ICHRG2 | ICHRG3 | CHGAUTOB;
pmic_reg_write(p, REG_CHARGE, val);
/* power up the system first */
pmic_reg_write(p, REG_POWER_MISC, PWUP);
/* Set core voltage to 1.1V */
pmic_reg_read(p, REG_SW_0, &val);
val = (val & ~SWx_VOLT_MASK) | SWx_1_100V;
pmic_reg_write(p, REG_SW_0, val);
/* Setup VCC (SW2) to 1.25 */
pmic_reg_read(p, REG_SW_1, &val);
val = (val & ~SWx_VOLT_MASK) | SWx_1_250V;
pmic_reg_write(p, REG_SW_1, val);
/* Setup 1V2_DIG1 (SW3) to 1.25 */
pmic_reg_read(p, REG_SW_2, &val);
val = (val & ~SWx_VOLT_MASK) | SWx_1_250V;
pmic_reg_write(p, REG_SW_2, val);
udelay(50);
/* Raise the core frequency to 800MHz */
writel(0x0, &mxc_ccm->cacrr);
/* Set switchers in Auto in NORMAL mode & STANDBY mode */
/* Setup the switcher mode for SW1 & SW2*/
pmic_reg_read(p, REG_SW_4, &val);
val = (val & ~((SWMODE_MASK << SWMODE1_SHIFT) |
(SWMODE_MASK << SWMODE2_SHIFT)));
val |= (SWMODE_AUTO_AUTO << SWMODE1_SHIFT) |
(SWMODE_AUTO_AUTO << SWMODE2_SHIFT);
pmic_reg_write(p, REG_SW_4, val);
/* Setup the switcher mode for SW3 & SW4 */
pmic_reg_read(p, REG_SW_5, &val);
val = (val & ~((SWMODE_MASK << SWMODE3_SHIFT) |
(SWMODE_MASK << SWMODE4_SHIFT)));
val |= (SWMODE_AUTO_AUTO << SWMODE3_SHIFT) |
(SWMODE_AUTO_AUTO << SWMODE4_SHIFT);
pmic_reg_write(p, REG_SW_5, val);
/* Set VDIG to 1.65V, VGEN3 to 1.8V, VCAM to 2.6V */
pmic_reg_read(p, REG_SETTING_0, &val);
val &= ~(VCAM_MASK | VGEN3_MASK | VDIG_MASK);
val |= VDIG_1_65 | VGEN3_1_8 | VCAM_2_6;
pmic_reg_write(p, REG_SETTING_0, val);
/* Set VVIDEO to 2.775V, VAUDIO to 3V, VSD to 3.15V */
pmic_reg_read(p, REG_SETTING_1, &val);
val &= ~(VVIDEO_MASK | VSD_MASK | VAUDIO_MASK);
val |= VSD_3_15 | VAUDIO_3_0 | VVIDEO_2_775;
pmic_reg_write(p, REG_SETTING_1, val);
/* Configure VGEN3 and VCAM regulators to use external PNP */
val = VGEN3CONFIG | VCAMCONFIG;
pmic_reg_write(p, REG_MODE_1, val);
udelay(200);
/* Enable VGEN3, VCAM, VAUDIO, VVIDEO, VSD regulators */
val = VGEN3EN | VGEN3CONFIG | VCAMEN | VCAMCONFIG |
VVIDEOEN | VAUDIOEN | VSDEN;
pmic_reg_write(p, REG_MODE_1, val);
imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX51_PAD_EIM_A20__GPIO2_14,
NO_PAD_CTRL));
gpio_request(IMX_GPIO_NR(2, 14), "gpio2_14");
gpio_direction_output(IMX_GPIO_NR(2, 14), 0);
udelay(500);
gpio_set_value(IMX_GPIO_NR(2, 14), 1);
}
int board_early_init_f(void)
{
setup_iomux_uart();
setup_iomux_lcd();
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
return 0;
}
#ifdef CONFIG_BOARD_LATE_INIT
int board_late_init(void)
{
#ifdef CONFIG_MXC_SPI
setup_iomux_spi();
power_init();
#endif
return 0;
}
#endif
/*
* Do not overwrite the console
* Use always serial for U-Boot console
*/
int overwrite_console(void)
{
return 1;
}
int checkboard(void)
{
puts("Board: MX51EVK\n");
return 0;
}