mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-18 02:38:56 +00:00
401d1c4f5d
Move this out of the common header and include it only where needed. In a number of cases this requires adding "struct udevice;" to avoid adding another large header or in other cases replacing / adding missing header files that had been pulled in, very indirectly. Finally, we have a few cases where we did not need to include <asm/global_data.h> at all, so remove that include. Signed-off-by: Simon Glass <sjg@chromium.org> Signed-off-by: Tom Rini <trini@konsulko.com>
112 lines
2.6 KiB
C
112 lines
2.6 KiB
C
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* (C) Copyright 2000-2003
|
|
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
|
|
*
|
|
* Copyright (C) 2004-2007, 2012 Freescale Semiconductor, Inc.
|
|
* TsiChung Liew (Tsi-Chung.Liew@freescale.com)
|
|
*/
|
|
|
|
#include <config.h>
|
|
#include <common.h>
|
|
#include <init.h>
|
|
#include <asm/global_data.h>
|
|
#include <asm/immap.h>
|
|
#include <asm/io.h>
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
int checkboard(void)
|
|
{
|
|
puts("Board: ");
|
|
puts("Freescale M5235 EVB\n");
|
|
return 0;
|
|
};
|
|
|
|
int dram_init(void)
|
|
{
|
|
sdram_t *sdram = (sdram_t *)(MMAP_SDRAM);
|
|
gpio_t *gpio = (gpio_t *)(MMAP_GPIO);
|
|
u32 dramsize, i, dramclk;
|
|
|
|
/*
|
|
* When booting from external Flash, the port-size is less than
|
|
* the port-size of SDRAM. In this case it is necessary to enable
|
|
* Data[15:0] on Port Address/Data.
|
|
*/
|
|
out_8(&gpio->par_ad,
|
|
GPIO_PAR_AD_ADDR23 | GPIO_PAR_AD_ADDR22 | GPIO_PAR_AD_ADDR21 |
|
|
GPIO_PAR_AD_DATAL);
|
|
|
|
/* Initialize PAR to enable SDRAM signals */
|
|
out_8(&gpio->par_sdram,
|
|
GPIO_PAR_SDRAM_SDWE | GPIO_PAR_SDRAM_SCAS |
|
|
GPIO_PAR_SDRAM_SRAS | GPIO_PAR_SDRAM_SCKE |
|
|
GPIO_PAR_SDRAM_SDCS(3));
|
|
|
|
dramsize = CONFIG_SYS_SDRAM_SIZE * 0x100000;
|
|
for (i = 0x13; i < 0x20; i++) {
|
|
if (dramsize == (1 << i))
|
|
break;
|
|
}
|
|
i--;
|
|
|
|
if (!(in_be32(&sdram->dacr0) & SDRAMC_DARCn_RE)) {
|
|
dramclk = gd->bus_clk / (CONFIG_SYS_HZ * CONFIG_SYS_HZ);
|
|
|
|
/* Initialize DRAM Control Register: DCR */
|
|
out_be16(&sdram->dcr, SDRAMC_DCR_RTIM_9CLKS |
|
|
SDRAMC_DCR_RTIM_6CLKS |
|
|
SDRAMC_DCR_RC((15 * dramclk) >> 4));
|
|
|
|
/* Initialize DACR0 */
|
|
out_be32(&sdram->dacr0,
|
|
SDRAMC_DARCn_BA(CONFIG_SYS_SDRAM_BASE) |
|
|
SDRAMC_DARCn_CASL_C1 | SDRAMC_DARCn_CBM_CMD20 |
|
|
SDRAMC_DARCn_PS_32);
|
|
asm("nop");
|
|
|
|
/* Initialize DMR0 */
|
|
out_be32(&sdram->dmr0,
|
|
((dramsize - 1) & 0xFFFC0000) | SDRAMC_DMRn_V);
|
|
asm("nop");
|
|
|
|
/* Set IP (bit 3) in DACR */
|
|
setbits_be32(&sdram->dacr0, SDRAMC_DARCn_IP);
|
|
|
|
/* Wait 30ns to allow banks to precharge */
|
|
for (i = 0; i < 5; i++) {
|
|
asm("nop");
|
|
}
|
|
|
|
/* Write to this block to initiate precharge */
|
|
*(u32 *) (CONFIG_SYS_SDRAM_BASE) = 0xA5A59696;
|
|
|
|
/* Set RE (bit 15) in DACR */
|
|
setbits_be32(&sdram->dacr0, SDRAMC_DARCn_RE);
|
|
|
|
/* Wait for at least 8 auto refresh cycles to occur */
|
|
for (i = 0; i < 0x2000; i++) {
|
|
asm("nop");
|
|
}
|
|
|
|
/* Finish the configuration by issuing the MRS. */
|
|
setbits_be32(&sdram->dacr0, SDRAMC_DARCn_IMRS);
|
|
asm("nop");
|
|
|
|
/* Write to the SDRAM Mode Register */
|
|
*(u32 *) (CONFIG_SYS_SDRAM_BASE + 0x400) = 0xA5A59696;
|
|
}
|
|
|
|
gd->ram_size = dramsize;
|
|
|
|
return 0;
|
|
};
|
|
|
|
int testdram(void)
|
|
{
|
|
/* TODO: XXX XXX XXX */
|
|
printf("DRAM test not implemented!\n");
|
|
|
|
return (0);
|
|
}
|