u-boot/include/configs/NETTA.h
Stefan Roese 68d7d65100 Separate mtdparts command from jffs2
Currently the mtdparts commands are included in the jffs2 command support.
This doesn't make sense anymore since other commands (e.g. UBI) use this
infrastructure as well now. This patch separates the mtdparts commands from
the jffs2 commands making it possible to only select mtdparts when no JFFS2
support is needed.

Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
2009-03-20 22:39:14 +01:00

797 lines
29 KiB
C

/*
* (C) Copyright 2000-2004
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* See file CREDITS for list of people who contributed to this
* project.
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of
* the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston,
* MA 02111-1307 USA
*/
/*
* Pantelis Antoniou, Intracom S.A., panto@intracom.gr
* U-Boot port on NetTA4 board
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_MPC885 1 /* This is a MPC885 CPU */
#define CONFIG_NETTA 1 /* ...on a NetTA board */
#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
#undef CONFIG_8xx_CONS_SMC2
#undef CONFIG_8xx_CONS_NONE
#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */
/* #define CONFIG_XIN 10000000 */
#define CONFIG_XIN 50000000
#define MPC8XX_HZ 120000000
/* #define MPC8XX_HZ 100000000 */
/* #define MPC8XX_HZ 50000000 */
/* #define MPC8XX_HZ 80000000 */
#define CONFIG_8xx_GCLK_FREQ MPC8XX_HZ
#if 0
#define CONFIG_BOOTDELAY -1 /* autoboot disabled */
#else
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#endif
#undef CONFIG_CLOCKS_IN_MHZ /* clocks NOT passsed to Linux in MHz */
#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"
#undef CONFIG_BOOTARGS
#define CONFIG_BOOTCOMMAND \
"tftpboot; " \
"setenv bootargs root=/dev/nfs rw nfsroot=${serverip}:${rootpath} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:${hostname}::off;" \
"bootm"
#define CONFIG_LOADS_ECHO 0 /* echo off for serial download */
#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_HW_WATCHDOG
#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_SUBNETMASK
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_NISDOMAIN
#undef CONFIG_MAC_PARTITION
#undef CONFIG_DOS_PARTITION
#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */
#define CONFIG_NET_MULTI 1 /* the only way to get the FEC in */
#define FEC_ENET 1 /* eth.c needs it that way... */
#undef CONFIG_SYS_DISCOVER_PHY /* do not discover phys */
#define CONFIG_MII 1
#define CONFIG_MII_INIT 1
#define CONFIG_RMII 1 /* use RMII interface */
#if defined(CONFIG_NETTA_ISDN)
#define CONFIG_ETHER_ON_FEC1 1
#define CONFIG_FEC1_PHY 1 /* phy address of FEC1 */
#define CONFIG_FEC1_PHY_NORXERR 1
#undef CONFIG_ETHER_ON_FEC2
#else
#define CONFIG_ETHER_ON_FEC1 1
#define CONFIG_FEC1_PHY 8 /* phy address of FEC1 */
#define CONFIG_FEC1_PHY_NORXERR 1
#define CONFIG_ETHER_ON_FEC2 1
#define CONFIG_FEC2_PHY 1 /* phy address of FEC2 */
#define CONFIG_FEC2_PHY_NORXERR 1
#endif
#define CONFIG_ENV_OVERWRITE 1 /* allow modification of vendor params */
/* POST support */
#define CONFIG_POST (CONFIG_SYS_POST_MEMORY | \
CONFIG_SYS_POST_CODEC | \
CONFIG_SYS_POST_DSP )
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_CDP
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_FAT
#define CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCMCIA
#define CONFIG_CMD_PING
#define CONFIG_BOARD_EARLY_INIT_F 1
#define CONFIG_MISC_INIT_R
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_PROMPT "=> " /* Monitor Command Prompt */
#define CONFIG_SYS_HUSH_PARSER 1
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x0300000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0700000 /* 3 ... 7 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_HZ 1000 /* decrementer freq: 1 ms ticks */
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Internal Memory Mapped Register
*/
#define CONFIG_SYS_IMMR 0xFF000000
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
#define CONFIG_SYS_INIT_RAM_END 0x3000 /* End of used area in DPRAM */
#define CONFIG_SYS_GBL_DATA_SIZE 64 /* size in bytes reserved for initial data */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_FLASH_BASE 0x40000000
#if defined(DEBUG)
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
#else
#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
#endif
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 8 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_SECT_SIZE 0x10000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x60000)
#define CONFIG_ENV_OFFSET 0
#define CONFIG_ENV_SIZE 0x4000
#define CONFIG_ENV_ADDR_REDUND (CONFIG_SYS_FLASH_BASE + 0x70000)
#define CONFIG_ENV_OFFSET_REDUND 0
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
#endif
/*-----------------------------------------------------------------------
* SYPCR - System Protection Control 11-9
* SYPCR can only be written once after reset!
*-----------------------------------------------------------------------
* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
*/
#if defined(CONFIG_WATCHDOG)
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
SYPCR_SWE | SYPCR_SWRI| SYPCR_SWP)
#else
#define CONFIG_SYS_SYPCR (SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
#endif
/*-----------------------------------------------------------------------
* SIUMCR - SIU Module Configuration 11-6
*-----------------------------------------------------------------------
* PCMCIA config., multi-function pin tri-state
*/
#ifndef CONFIG_CAN_DRIVER
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
#else /* we must activate GPL5 in the SIUMCR for CAN */
#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01 | SIUMCR_FRC)
#endif /* CONFIG_CAN_DRIVER */
/*-----------------------------------------------------------------------
* TBSCR - Time Base Status and Control 11-26
*-----------------------------------------------------------------------
* Clear Reference Interrupt Status, Timebase freezing enabled
*/
#define CONFIG_SYS_TBSCR (TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)
/*-----------------------------------------------------------------------
* RTCSC - Real-Time Clock Status and Control Register 11-27
*-----------------------------------------------------------------------
*/
#define CONFIG_SYS_RTCSC (RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)
/*-----------------------------------------------------------------------
* PISCR - Periodic Interrupt Status and Control 11-31
*-----------------------------------------------------------------------
* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
*/
#define CONFIG_SYS_PISCR (PISCR_PS | PISCR_PITF)
/*-----------------------------------------------------------------------
* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
*-----------------------------------------------------------------------
* Reset PLL lock status sticky bit, timer expired status bit and timer
* interrupt status bit
*
*/
#if CONFIG_XIN == 10000000
#if MPC8XX_HZ == 120000000
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
(0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
PLPRCR_TEXPS)
#elif MPC8XX_HZ == 100000000
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
(0 << PLPRCR_S_SHIFT) | (10 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
PLPRCR_TEXPS)
#elif MPC8XX_HZ == 50000000
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
(1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
PLPRCR_TEXPS)
#elif MPC8XX_HZ == 25000000
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
(2 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (3 << PLPRCR_PDF_SHIFT) | \
PLPRCR_TEXPS)
#elif MPC8XX_HZ == 40000000
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
(1 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
PLPRCR_TEXPS)
#elif MPC8XX_HZ == 75000000
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
(1 << PLPRCR_S_SHIFT) | (15 << PLPRCR_MFI_SHIFT) | (0 << PLPRCR_PDF_SHIFT) | \
PLPRCR_TEXPS)
#else
#error unsupported CPU freq for XIN = 10MHz
#endif
#elif CONFIG_XIN == 50000000
#if MPC8XX_HZ == 120000000
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
(0 << PLPRCR_S_SHIFT) | (12 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
PLPRCR_TEXPS)
#elif MPC8XX_HZ == 100000000
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
(0 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
PLPRCR_TEXPS)
#elif MPC8XX_HZ == 80000000
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
(0 << PLPRCR_S_SHIFT) | (8 << PLPRCR_MFI_SHIFT) | (4 << PLPRCR_PDF_SHIFT) | \
PLPRCR_TEXPS)
#elif MPC8XX_HZ == 50000000
#define CONFIG_SYS_PLPRCR ((0 << PLPRCR_MFN_SHIFT) | (0 << PLPRCR_MFD_SHIFT) | \
(1 << PLPRCR_S_SHIFT) | (6 << PLPRCR_MFI_SHIFT) | (2 << PLPRCR_PDF_SHIFT) | \
PLPRCR_TEXPS)
#else
#error unsupported CPU freq for XIN = 50MHz
#endif
#else
#error unsupported XIN freq
#endif
/*
*-----------------------------------------------------------------------
* SCCR - System Clock and reset Control Register 15-27
*-----------------------------------------------------------------------
* Set clock output, timebase and RTC source and divider,
* power management and some other internal clocks
*
* Note: When TBS == 0 the timebase is independent of current cpu clock.
*/
#define SCCR_MASK SCCR_EBDF11
#if MPC8XX_HZ > 66666666
#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ SCCR_CRQEN | \
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL111 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00 | SCCR_EBDF01)
#else
#define CONFIG_SYS_SCCR (/* SCCR_TBS | */ SCCR_CRQEN | \
SCCR_COM00 | SCCR_DFSYNC00 | SCCR_DFBRG00 | \
SCCR_DFNL111 | SCCR_DFNH000 | SCCR_DFLCD000 | \
SCCR_DFALCD00)
#endif
/*-----------------------------------------------------------------------
*
*-----------------------------------------------------------------------
*
*/
/*#define CONFIG_SYS_DER 0x2002000F*/
#define CONFIG_SYS_DER 0
/*
* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
/* used to re-map FLASH both when starting from SRAM or FLASH:
* restrict access enough to keep SRAM working (if any)
* but not too much to meddle with FLASH accesses
*/
#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */
/* FLASH timing: ACS = 11, TRLX = 0, CSNT = 1, SCY = 5, EHTR = 1 */
#define CONFIG_SYS_OR_TIMING_FLASH (OR_CSNT_SAM | OR_BI | OR_SCY_5_CLK | OR_TRLX)
#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_PS_8 | BR_V )
/*
* BR3 and OR3 (SDRAM)
*
*/
#define SDRAM_BASE3_PRELIM 0x00000000 /* SDRAM bank #0 */
#define SDRAM_MAX_SIZE (256 << 20) /* max 256MB per bank */
/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
#define CONFIG_SYS_OR_TIMING_SDRAM (OR_CSNT_SAM | OR_G5LS)
#define CONFIG_SYS_OR3_PRELIM ((0xFFFFFFFFLU & ~(SDRAM_MAX_SIZE - 1)) | CONFIG_SYS_OR_TIMING_SDRAM)
#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMB | BR_PS_32 | BR_V)
/*
* Memory Periodic Timer Prescaler
*/
/*
* Memory Periodic Timer Prescaler
*
* The Divider for PTA (refresh timer) configuration is based on an
* example SDRAM configuration (64 MBit, one bank). The adjustment to
* the number of chip selects (NCS) and the actually needed refresh
* rate is done by setting MPTPR.
*
* PTA is calculated from
* PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
*
* gclk CPU clock (not bus clock!)
* Trefresh Refresh cycle * 4 (four word bursts used)
*
* 4096 Rows from SDRAM example configuration
* 1000 factor s -> ms
* 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
* 4 Number of refresh cycles per period
* 64 Refresh cycle in ms per number of rows
* --------------------------------------------
* Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
*
* 50 MHz => 50.000.000 / Divider = 98
* 66 Mhz => 66.000.000 / Divider = 129
* 80 Mhz => 80.000.000 / Divider = 156
*/
#if MPC8XX_HZ == 120000000
#define CONFIG_SYS_MAMR_PTA 234
#elif MPC8XX_HZ == 100000000
#define CONFIG_SYS_MAMR_PTA 195
#elif MPC8XX_HZ == 80000000
#define CONFIG_SYS_MAMR_PTA 156
#elif MPC8XX_HZ == 50000000
#define CONFIG_SYS_MAMR_PTA 98
#else
#error Unknown frequency
#endif
/*
* For 16 MBit, refresh rates could be 31.3 us
* (= 64 ms / 2K = 125 / quad bursts).
* For a simpler initialization, 15.6 us is used instead.
*
* #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
* #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
*/
#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */
/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */
/*
* MAMR settings for SDRAM
*/
/* 8 column SDRAM */
#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/* 9 column SDRAM */
#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) | MAMR_PTAE | \
MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 | \
MAMR_RLFA_1X | MAMR_WLFA_1X | MAMR_TLFA_4X)
/*
* Internal Definitions
*
* Boot Flags
*/
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
#define CONFIG_LAST_STAGE_INIT /* needed to reset the damn phys */
/***********************************************************************************************************
Pin definitions:
+------+----------------+--------+------------------------------------------------------------
| # | Name | Type | Comment
+------+----------------+--------+------------------------------------------------------------
| PA3 | OK_ETH_3V | Input | CISCO Ethernet power OK
| | | | (NetRoute: FEC1, TA: FEC2) (0=power OK)
| PA6 | P_VCCD1 | Output | TPS2211A PCMCIA
| PA7 | DCL1_3V | Periph | IDL1 PCM clock
| PA8 | DSP_DR1 | Periph | IDL1 PCM Data Rx
| PA9 | L1TXDA | Periph | IDL1 PCM Data Tx
| PA10 | P_VCCD0 | Output | TPS2211A PCMCIA
| PA12 | P_SHDN | Output | TPS2211A PCMCIA
| PA13 | ETH_LOOP | Output | CISCO Loopback remote power
| | | | (NetRoute: FEC1, TA: FEC2) (1=NORMAL)
| PA14 | P_VPPD0 | Output | TPS2211A PCMCIA
| PA15 | P_VPPD1 | Output | TPS2211A PCMCIA
| PB14 | SPIEN_FXO | Output | SPI CS for FXO daughter-board
| PB15 | SPIEN_S1 | Output | SPI CS for S-interface 1 (NetRoute only)
| PB16 | DREQ1 | Output | D channel request for S-interface chip 1.
| PB17 | L1ST3 | Periph | IDL1 timeslot enable signal for PPC
| PB18 | L1ST2 | Periph | IDL1 timeslot enable signal for PPC
| PB19 | SPIEN_S2 | Output | SPI CS for S-interface 2 (NetRoute only)
| PB20 | SPIEN_SEEPROM | Output | SPI CS for serial eeprom
| PB21 | LEDIO | Output | Led mode indication for PHY
| PB22 | UART_CTS | Input | UART CTS
| PB23 | UART_RTS | Output | UART RTS
| PB24 | UART_RX | Periph | UART Data Rx
| PB25 | UART_TX | Periph | UART Data Tx
| PB26 | RMII-MDC | Periph | Free for future use (MII mgt clock)
| PB27 | RMII-MDIO | Periph | Free for future use (MII mgt data)
| PB28 | SPI_RXD_3V | Input | SPI Data Rx
| PB29 | SPI_TXD | Output | SPI Data Tx
| PB30 | SPI_CLK | Output | SPI Clock
| PB31 | RMII1-REFCLK | Periph | RMII reference clock for FEC1
| PC4 | PHY1_LINK | Input | PHY link state FEC1 (interrupt)
| PC5 | PHY2_LINK | Input | PHY link state FEC2 (interrupt)
| PC6 | RMII1-MDINT | Input | PHY prog interrupt FEC1 (interrupt)
| PC7 | RMII2-MDINT | Input | PHY prog interrupt FEC1 (interrupt)
| PC8 | P_OC | Input | TPS2211A PCMCIA overcurrent (interrupt) (1=OK)
| PC9 | COM_HOOK1 | Input | Codec interrupt chip #1 (interrupt)
| PC10 | COM_HOOK2 | Input | Codec interrupt chip #2 (interrupt)
| PC11 | COM_HOOK4 | Input | Codec interrupt chip #4 (interrupt)
| PC12 | COM_HOOK3 | Input | Codec interrupt chip #3 (interrupt)
| PC13 | F_RY_BY | Input | NAND ready signal (interrupt)
| PC14 | FAN_OK | Input | Fan status signal (interrupt) (1=OK)
| PC15 | PC15_DIRECT0 | Periph | PCMCIA DMA request.
| PD3 | F_ALE | Output | NAND
| PD4 | F_CLE | Output | NAND
| PD5 | F_CE | Output | NAND
| PD6 | DSP_INT | Output | DSP debug interrupt
| PD7 | DSP_RESET | Output | DSP reset
| PD8 | RMII_MDC | Periph | MII mgt clock
| PD9 | SPIEN_C1 | Output | SPI CS for codec #1
| PD10 | SPIEN_C2 | Output | SPI CS for codec #2
| PD11 | SPIEN_C3 | Output | SPI CS for codec #3
| PD12 | FSC2 | Periph | IDL2 frame sync
| PD13 | DGRANT2 | Input | D channel grant from S #2
| PD14 | SPIEN_C4 | Output | SPI CS for codec #4
| PD15 | TP700 | Output | Testpoint for software debugging
| PE14 | RMII2-TXD0 | Periph | FEC2 transmit data
| PE15 | RMII2-TXD1 | Periph | FEC2 transmit data
| PE16 | RMII2-REFCLK | Periph | TA: RMII ref clock for
| | DCL2 | Periph | NetRoute: PCM clock #2
| PE17 | TP703 | Output | Testpoint for software debugging
| PE18 | DGRANT1 | Input | D channel grant from S #1
| PE19 | RMII2-TXEN | Periph | TA: FEC2 tx enable
| | PCM2OUT | Periph | NetRoute: Tx data for IDL2
| PE20 | FSC1 | Periph | IDL1 frame sync
| PE21 | RMII2-RXD0 | Periph | FEC2 receive data
| PE22 | RMII2-RXD1 | Periph | FEC2 receive data
| PE23 | L1ST1 | Periph | IDL1 timeslot enable signal for PPC
| PE24 | U-N1 | Output | Select user/network for S #1 (0=user)
| PE25 | U-N2 | Output | Select user/network for S #2 (0=user)
| PE26 | RMII2-RXDV | Periph | FEC2 valid
| PE27 | DREQ2 | Output | D channel request for S #2.
| PE28 | FPGA_DONE | Input | FPGA done signal
| PE29 | FPGA_INIT | Output | FPGA init signal
| PE30 | UDOUT2_3V | Input | IDL2 PCM input
| PE31 | | | Free
+------+----------------+--------+---------------------------------------------------
Chip selects:
+------+----------------+------------------------------------------------------------
| # | Name | Comment
+------+----------------+------------------------------------------------------------
| CS0 | CS0 | Boot flash
| CS1 | CS_FLASH | NAND flash
| CS2 | CS_DSP | DSP
| CS3 | DCS_DRAM | DRAM
| CS4 | CS_ER1 | External output register
+------+----------------+------------------------------------------------------------
Interrupts:
+------+----------------+------------------------------------------------------------
| # | Name | Comment
+------+----------------+------------------------------------------------------------
| IRQ1 | UINTER_3V | S interupt chips interrupt (common)
| IRQ3 | IRQ_DSP | DSP interrupt
| IRQ4 | IRQ_DSP1 | Extra DSP interrupt
+------+----------------+------------------------------------------------------------
*************************************************************************************************/
#define DSP_SIZE 0x00010000 /* 64K */
#define NAND_SIZE 0x00010000 /* 64K */
#define ER_SIZE 0x00010000 /* 64K */
#define DUMMY_SIZE 0x00010000 /* 64K */
#define DSP_BASE 0xF1000000
#define NAND_BASE 0xF1010000
#define ER_BASE 0xF1020000
#define DUMMY_BASE 0xF1FF0000
/****************************************************************/
/* NAND */
#define CONFIG_NAND_LEGACY
#define CONFIG_SYS_NAND_BASE NAND_BASE
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_MTD_NAND_UNSAFE
#define CONFIG_SYS_MAX_NAND_DEVICE 1
/* #define NAND_NO_RB */
#define SECTORSIZE 512
#define ADDR_COLUMN 1
#define ADDR_PAGE 2
#define ADDR_COLUMN_PAGE 3
#define NAND_ChipID_UNKNOWN 0x00
#define NAND_MAX_FLOORS 1
/* ALE = PD3, CLE = PD4, CE = PD5, F_RY_BY = PC13 */
#define NAND_DISABLE_CE(nand) \
do { \
(((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) |= (1 << (15 - 5)); \
} while(0)
#define NAND_ENABLE_CE(nand) \
do { \
(((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 5)); \
} while(0)
#define NAND_CTL_CLRALE(nandptr) \
do { \
(((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 3)); \
} while(0)
#define NAND_CTL_SETALE(nandptr) \
do { \
(((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) |= (1 << (15 - 3)); \
} while(0)
#define NAND_CTL_CLRCLE(nandptr) \
do { \
(((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) &= ~(1 << (15 - 4)); \
} while(0)
#define NAND_CTL_SETCLE(nandptr) \
do { \
(((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pddat) |= (1 << (15 - 4)); \
} while(0)
#ifndef NAND_NO_RB
#define NAND_WAIT_READY(nand) \
do { \
while ((((volatile immap_t *)CONFIG_SYS_IMMR)->im_ioport.iop_pcdat & (1 << (15 - 13))) == 0) { \
WATCHDOG_RESET(); \
} \
} while (0)
#else
#define NAND_WAIT_READY(nand) udelay(12)
#endif
#define WRITE_NAND_COMMAND(d, adr) \
do { \
*(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
} while(0)
#define WRITE_NAND_ADDRESS(d, adr) \
do { \
*(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
} while(0)
#define WRITE_NAND(d, adr) \
do { \
*(volatile unsigned char *)((unsigned long)(adr)) = (unsigned char)(d); \
} while(0)
#define READ_NAND(adr) \
((unsigned char)(*(volatile unsigned char *)(unsigned long)(adr)))
#define CONFIG_JFFS2_NAND 1 /* jffs2 on nand support */
#define NAND_CACHE_PAGES 16 /* size of nand cache in 512 bytes pages */
/*
* JFFS2 partitions
*
*/
/* No command line, one static partition, whole device */
#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nand0"
#define CONFIG_JFFS2_PART_SIZE 0x00100000
#define CONFIG_JFFS2_PART_OFFSET 0x00200000
/* mtdparts command line support */
/* Note: fake mtd_id used, no linux mtd map file */
/*
#define CONFIG_CMD_MTDPARTS
#define MTDIDS_DEFAULT "nand0=netta-nand"
#define MTDPARTS_DEFAULT "mtdparts=netta-nand:1m@2m(jffs2)"
*/
/*****************************************************************************/
#define CONFIG_SYS_DIRECT_FLASH_TFTP
#define CONFIG_SYS_DIRECT_NAND_TFTP
/*****************************************************************************/
#if 1
/*-----------------------------------------------------------------------
* PCMCIA stuff
*-----------------------------------------------------------------------
*/
#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )
/*-----------------------------------------------------------------------
* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
*-----------------------------------------------------------------------
*/
#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */
#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
#undef CONFIG_IDE_LED /* LED for ide not supported */
#undef CONFIG_IDE_RESET /* reset for ide not supported */
#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */
#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000
#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR
/* Offset for data I/O */
#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for normal register accesses */
#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)
/* Offset for alternate registers */
#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100
#define CONFIG_MAC_PARTITION
#define CONFIG_DOS_PARTITION
#endif
/*************************************************************************************************/
#define CONFIG_CDP_DEVICE_ID 20
#define CONFIG_CDP_DEVICE_ID_PREFIX "NT" /* netta */
#define CONFIG_CDP_PORT_ID "eth%d"
#define CONFIG_CDP_CAPABILITIES 0x00000010
#define CONFIG_CDP_VERSION "u-boot 1.0" " " U_BOOT_DATE " " U_BOOT_TIME
#define CONFIG_CDP_PLATFORM "Intracom NetTA"
#define CONFIG_CDP_TRIGGER 0x20020001
#define CONFIG_CDP_POWER_CONSUMPTION 4300 /* 90 mA @ 48V */
#define CONFIG_CDP_APPLIANCE_VLAN_TYPE 0x01 /* ipphone? */
/*************************************************************************************************/
#define CONFIG_AUTO_COMPLETE 1
/*************************************************************************************************/
#define CONFIG_CRC32_VERIFY 1
/*************************************************************************************************/
#define CONFIG_HUSH_OLD_PARSER_COMPATIBLE 1
/*************************************************************************************************/
#endif /* __CONFIG_H */