mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-18 02:38:56 +00:00
1fd92db83d
Update the naming convention used in the network stack functions and variables that Ethernet drivers use to interact with it. This cleans up the temporary hacks that were added to this interface along with the DM support. This patch has a few remaining checkpatch.pl failures that would be out of the scope of this patch to fix (drivers that are in gross violation of checkpatch.pl). Signed-off-by: Joe Hershberger <joe.hershberger@ni.com> Acked-by: Simon Glass <sjg@chromium.org>
542 lines
13 KiB
C
542 lines
13 KiB
C
/*
|
|
* (C) Copyright 2002 Wolfgang Grandegger, wg@denx.de.
|
|
*
|
|
* This driver for AMD PCnet network controllers is derived from the
|
|
* Linux driver pcnet32.c written 1996-1999 by Thomas Bogendoerfer.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <malloc.h>
|
|
#include <net.h>
|
|
#include <netdev.h>
|
|
#include <asm/io.h>
|
|
#include <pci.h>
|
|
|
|
#define PCNET_DEBUG_LEVEL 0 /* 0=off, 1=init, 2=rx/tx */
|
|
|
|
#define PCNET_DEBUG1(fmt,args...) \
|
|
debug_cond(PCNET_DEBUG_LEVEL > 0, fmt ,##args)
|
|
#define PCNET_DEBUG2(fmt,args...) \
|
|
debug_cond(PCNET_DEBUG_LEVEL > 1, fmt ,##args)
|
|
|
|
#if !defined(CONF_PCNET_79C973) && defined(CONF_PCNET_79C975)
|
|
#error "Macro for PCnet chip version is not defined!"
|
|
#endif
|
|
|
|
/*
|
|
* Set the number of Tx and Rx buffers, using Log_2(# buffers).
|
|
* Reasonable default values are 4 Tx buffers, and 16 Rx buffers.
|
|
* That translates to 2 (4 == 2^^2) and 4 (16 == 2^^4).
|
|
*/
|
|
#define PCNET_LOG_TX_BUFFERS 0
|
|
#define PCNET_LOG_RX_BUFFERS 2
|
|
|
|
#define TX_RING_SIZE (1 << (PCNET_LOG_TX_BUFFERS))
|
|
#define TX_RING_LEN_BITS ((PCNET_LOG_TX_BUFFERS) << 12)
|
|
|
|
#define RX_RING_SIZE (1 << (PCNET_LOG_RX_BUFFERS))
|
|
#define RX_RING_LEN_BITS ((PCNET_LOG_RX_BUFFERS) << 4)
|
|
|
|
#define PKT_BUF_SZ 1544
|
|
|
|
/* The PCNET Rx and Tx ring descriptors. */
|
|
struct pcnet_rx_head {
|
|
u32 base;
|
|
s16 buf_length;
|
|
s16 status;
|
|
u32 msg_length;
|
|
u32 reserved;
|
|
};
|
|
|
|
struct pcnet_tx_head {
|
|
u32 base;
|
|
s16 length;
|
|
s16 status;
|
|
u32 misc;
|
|
u32 reserved;
|
|
};
|
|
|
|
/* The PCNET 32-Bit initialization block, described in databook. */
|
|
struct pcnet_init_block {
|
|
u16 mode;
|
|
u16 tlen_rlen;
|
|
u8 phys_addr[6];
|
|
u16 reserved;
|
|
u32 filter[2];
|
|
/* Receive and transmit ring base, along with extra bits. */
|
|
u32 rx_ring;
|
|
u32 tx_ring;
|
|
u32 reserved2;
|
|
};
|
|
|
|
struct pcnet_uncached_priv {
|
|
struct pcnet_rx_head rx_ring[RX_RING_SIZE];
|
|
struct pcnet_tx_head tx_ring[TX_RING_SIZE];
|
|
struct pcnet_init_block init_block;
|
|
};
|
|
|
|
typedef struct pcnet_priv {
|
|
struct pcnet_uncached_priv *uc;
|
|
/* Receive Buffer space */
|
|
unsigned char (*rx_buf)[RX_RING_SIZE][PKT_BUF_SZ + 4];
|
|
int cur_rx;
|
|
int cur_tx;
|
|
} pcnet_priv_t;
|
|
|
|
static pcnet_priv_t *lp;
|
|
|
|
/* Offsets from base I/O address for WIO mode */
|
|
#define PCNET_RDP 0x10
|
|
#define PCNET_RAP 0x12
|
|
#define PCNET_RESET 0x14
|
|
#define PCNET_BDP 0x16
|
|
|
|
static u16 pcnet_read_csr(struct eth_device *dev, int index)
|
|
{
|
|
outw(index, dev->iobase + PCNET_RAP);
|
|
return inw(dev->iobase + PCNET_RDP);
|
|
}
|
|
|
|
static void pcnet_write_csr(struct eth_device *dev, int index, u16 val)
|
|
{
|
|
outw(index, dev->iobase + PCNET_RAP);
|
|
outw(val, dev->iobase + PCNET_RDP);
|
|
}
|
|
|
|
static u16 pcnet_read_bcr(struct eth_device *dev, int index)
|
|
{
|
|
outw(index, dev->iobase + PCNET_RAP);
|
|
return inw(dev->iobase + PCNET_BDP);
|
|
}
|
|
|
|
static void pcnet_write_bcr(struct eth_device *dev, int index, u16 val)
|
|
{
|
|
outw(index, dev->iobase + PCNET_RAP);
|
|
outw(val, dev->iobase + PCNET_BDP);
|
|
}
|
|
|
|
static void pcnet_reset(struct eth_device *dev)
|
|
{
|
|
inw(dev->iobase + PCNET_RESET);
|
|
}
|
|
|
|
static int pcnet_check(struct eth_device *dev)
|
|
{
|
|
outw(88, dev->iobase + PCNET_RAP);
|
|
return inw(dev->iobase + PCNET_RAP) == 88;
|
|
}
|
|
|
|
static int pcnet_init (struct eth_device *dev, bd_t * bis);
|
|
static int pcnet_send(struct eth_device *dev, void *packet, int length);
|
|
static int pcnet_recv (struct eth_device *dev);
|
|
static void pcnet_halt (struct eth_device *dev);
|
|
static int pcnet_probe (struct eth_device *dev, bd_t * bis, int dev_num);
|
|
|
|
#define PCI_TO_MEM(d, a) pci_virt_to_mem((pci_dev_t)d->priv, (a))
|
|
#define PCI_TO_MEM_LE(d,a) (u32)(cpu_to_le32(PCI_TO_MEM(d,a)))
|
|
|
|
static struct pci_device_id supported[] = {
|
|
{PCI_VENDOR_ID_AMD, PCI_DEVICE_ID_AMD_LANCE},
|
|
{}
|
|
};
|
|
|
|
|
|
int pcnet_initialize(bd_t *bis)
|
|
{
|
|
pci_dev_t devbusfn;
|
|
struct eth_device *dev;
|
|
u16 command, status;
|
|
int dev_nr = 0;
|
|
|
|
PCNET_DEBUG1("\npcnet_initialize...\n");
|
|
|
|
for (dev_nr = 0;; dev_nr++) {
|
|
|
|
/*
|
|
* Find the PCnet PCI device(s).
|
|
*/
|
|
devbusfn = pci_find_devices(supported, dev_nr);
|
|
if (devbusfn < 0)
|
|
break;
|
|
|
|
/*
|
|
* Allocate and pre-fill the device structure.
|
|
*/
|
|
dev = (struct eth_device *)malloc(sizeof(*dev));
|
|
if (!dev) {
|
|
printf("pcnet: Can not allocate memory\n");
|
|
break;
|
|
}
|
|
memset(dev, 0, sizeof(*dev));
|
|
dev->priv = (void *)devbusfn;
|
|
sprintf(dev->name, "pcnet#%d", dev_nr);
|
|
|
|
/*
|
|
* Setup the PCI device.
|
|
*/
|
|
pci_read_config_dword(devbusfn, PCI_BASE_ADDRESS_0,
|
|
(unsigned int *)&dev->iobase);
|
|
dev->iobase = pci_io_to_phys(devbusfn, dev->iobase);
|
|
dev->iobase &= ~0xf;
|
|
|
|
PCNET_DEBUG1("%s: devbusfn=0x%x iobase=0x%x: ",
|
|
dev->name, devbusfn, dev->iobase);
|
|
|
|
command = PCI_COMMAND_IO | PCI_COMMAND_MASTER;
|
|
pci_write_config_word(devbusfn, PCI_COMMAND, command);
|
|
pci_read_config_word(devbusfn, PCI_COMMAND, &status);
|
|
if ((status & command) != command) {
|
|
printf("%s: Couldn't enable IO access or Bus Mastering\n",
|
|
dev->name);
|
|
free(dev);
|
|
continue;
|
|
}
|
|
|
|
pci_write_config_byte(devbusfn, PCI_LATENCY_TIMER, 0x40);
|
|
|
|
/*
|
|
* Probe the PCnet chip.
|
|
*/
|
|
if (pcnet_probe(dev, bis, dev_nr) < 0) {
|
|
free(dev);
|
|
continue;
|
|
}
|
|
|
|
/*
|
|
* Setup device structure and register the driver.
|
|
*/
|
|
dev->init = pcnet_init;
|
|
dev->halt = pcnet_halt;
|
|
dev->send = pcnet_send;
|
|
dev->recv = pcnet_recv;
|
|
|
|
eth_register(dev);
|
|
}
|
|
|
|
udelay(10 * 1000);
|
|
|
|
return dev_nr;
|
|
}
|
|
|
|
static int pcnet_probe(struct eth_device *dev, bd_t *bis, int dev_nr)
|
|
{
|
|
int chip_version;
|
|
char *chipname;
|
|
|
|
#ifdef PCNET_HAS_PROM
|
|
int i;
|
|
#endif
|
|
|
|
/* Reset the PCnet controller */
|
|
pcnet_reset(dev);
|
|
|
|
/* Check if register access is working */
|
|
if (pcnet_read_csr(dev, 0) != 4 || !pcnet_check(dev)) {
|
|
printf("%s: CSR register access check failed\n", dev->name);
|
|
return -1;
|
|
}
|
|
|
|
/* Identify the chip */
|
|
chip_version =
|
|
pcnet_read_csr(dev, 88) | (pcnet_read_csr(dev, 89) << 16);
|
|
if ((chip_version & 0xfff) != 0x003)
|
|
return -1;
|
|
chip_version = (chip_version >> 12) & 0xffff;
|
|
switch (chip_version) {
|
|
case 0x2621:
|
|
chipname = "PCnet/PCI II 79C970A"; /* PCI */
|
|
break;
|
|
#ifdef CONFIG_PCNET_79C973
|
|
case 0x2625:
|
|
chipname = "PCnet/FAST III 79C973"; /* PCI */
|
|
break;
|
|
#endif
|
|
#ifdef CONFIG_PCNET_79C975
|
|
case 0x2627:
|
|
chipname = "PCnet/FAST III 79C975"; /* PCI */
|
|
break;
|
|
#endif
|
|
default:
|
|
printf("%s: PCnet version %#x not supported\n",
|
|
dev->name, chip_version);
|
|
return -1;
|
|
}
|
|
|
|
PCNET_DEBUG1("AMD %s\n", chipname);
|
|
|
|
#ifdef PCNET_HAS_PROM
|
|
/*
|
|
* In most chips, after a chip reset, the ethernet address is read from
|
|
* the station address PROM at the base address and programmed into the
|
|
* "Physical Address Registers" CSR12-14.
|
|
*/
|
|
for (i = 0; i < 3; i++) {
|
|
unsigned int val;
|
|
|
|
val = pcnet_read_csr(dev, i + 12) & 0x0ffff;
|
|
/* There may be endianness issues here. */
|
|
dev->enetaddr[2 * i] = val & 0x0ff;
|
|
dev->enetaddr[2 * i + 1] = (val >> 8) & 0x0ff;
|
|
}
|
|
#endif /* PCNET_HAS_PROM */
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int pcnet_init(struct eth_device *dev, bd_t *bis)
|
|
{
|
|
struct pcnet_uncached_priv *uc;
|
|
int i, val;
|
|
u32 addr;
|
|
|
|
PCNET_DEBUG1("%s: pcnet_init...\n", dev->name);
|
|
|
|
/* Switch pcnet to 32bit mode */
|
|
pcnet_write_bcr(dev, 20, 2);
|
|
|
|
/* Set/reset autoselect bit */
|
|
val = pcnet_read_bcr(dev, 2) & ~2;
|
|
val |= 2;
|
|
pcnet_write_bcr(dev, 2, val);
|
|
|
|
/* Enable auto negotiate, setup, disable fd */
|
|
val = pcnet_read_bcr(dev, 32) & ~0x98;
|
|
val |= 0x20;
|
|
pcnet_write_bcr(dev, 32, val);
|
|
|
|
/*
|
|
* Enable NOUFLO on supported controllers, with the transmit
|
|
* start point set to the full packet. This will cause entire
|
|
* packets to be buffered by the ethernet controller before
|
|
* transmission, eliminating underflows which are common on
|
|
* slower devices. Controllers which do not support NOUFLO will
|
|
* simply be left with a larger transmit FIFO threshold.
|
|
*/
|
|
val = pcnet_read_bcr(dev, 18);
|
|
val |= 1 << 11;
|
|
pcnet_write_bcr(dev, 18, val);
|
|
val = pcnet_read_csr(dev, 80);
|
|
val |= 0x3 << 10;
|
|
pcnet_write_csr(dev, 80, val);
|
|
|
|
/*
|
|
* We only maintain one structure because the drivers will never
|
|
* be used concurrently. In 32bit mode the RX and TX ring entries
|
|
* must be aligned on 16-byte boundaries.
|
|
*/
|
|
if (lp == NULL) {
|
|
addr = (u32)malloc(sizeof(pcnet_priv_t) + 0x10);
|
|
addr = (addr + 0xf) & ~0xf;
|
|
lp = (pcnet_priv_t *)addr;
|
|
|
|
addr = (u32)memalign(ARCH_DMA_MINALIGN, sizeof(*lp->uc));
|
|
flush_dcache_range(addr, addr + sizeof(*lp->uc));
|
|
addr = UNCACHED_SDRAM(addr);
|
|
lp->uc = (struct pcnet_uncached_priv *)addr;
|
|
|
|
addr = (u32)memalign(ARCH_DMA_MINALIGN, sizeof(*lp->rx_buf));
|
|
flush_dcache_range(addr, addr + sizeof(*lp->rx_buf));
|
|
lp->rx_buf = (void *)addr;
|
|
}
|
|
|
|
uc = lp->uc;
|
|
|
|
uc->init_block.mode = cpu_to_le16(0x0000);
|
|
uc->init_block.filter[0] = 0x00000000;
|
|
uc->init_block.filter[1] = 0x00000000;
|
|
|
|
/*
|
|
* Initialize the Rx ring.
|
|
*/
|
|
lp->cur_rx = 0;
|
|
for (i = 0; i < RX_RING_SIZE; i++) {
|
|
uc->rx_ring[i].base = PCI_TO_MEM_LE(dev, (*lp->rx_buf)[i]);
|
|
uc->rx_ring[i].buf_length = cpu_to_le16(-PKT_BUF_SZ);
|
|
uc->rx_ring[i].status = cpu_to_le16(0x8000);
|
|
PCNET_DEBUG1
|
|
("Rx%d: base=0x%x buf_length=0x%hx status=0x%hx\n", i,
|
|
uc->rx_ring[i].base, uc->rx_ring[i].buf_length,
|
|
uc->rx_ring[i].status);
|
|
}
|
|
|
|
/*
|
|
* Initialize the Tx ring. The Tx buffer address is filled in as
|
|
* needed, but we do need to clear the upper ownership bit.
|
|
*/
|
|
lp->cur_tx = 0;
|
|
for (i = 0; i < TX_RING_SIZE; i++) {
|
|
uc->tx_ring[i].base = 0;
|
|
uc->tx_ring[i].status = 0;
|
|
}
|
|
|
|
/*
|
|
* Setup Init Block.
|
|
*/
|
|
PCNET_DEBUG1("Init block at 0x%p: MAC", &lp->uc->init_block);
|
|
|
|
for (i = 0; i < 6; i++) {
|
|
lp->uc->init_block.phys_addr[i] = dev->enetaddr[i];
|
|
PCNET_DEBUG1(" %02x", lp->uc->init_block.phys_addr[i]);
|
|
}
|
|
|
|
uc->init_block.tlen_rlen = cpu_to_le16(TX_RING_LEN_BITS |
|
|
RX_RING_LEN_BITS);
|
|
uc->init_block.rx_ring = PCI_TO_MEM_LE(dev, uc->rx_ring);
|
|
uc->init_block.tx_ring = PCI_TO_MEM_LE(dev, uc->tx_ring);
|
|
|
|
PCNET_DEBUG1("\ntlen_rlen=0x%x rx_ring=0x%x tx_ring=0x%x\n",
|
|
uc->init_block.tlen_rlen,
|
|
uc->init_block.rx_ring, uc->init_block.tx_ring);
|
|
|
|
/*
|
|
* Tell the controller where the Init Block is located.
|
|
*/
|
|
barrier();
|
|
addr = PCI_TO_MEM(dev, &lp->uc->init_block);
|
|
pcnet_write_csr(dev, 1, addr & 0xffff);
|
|
pcnet_write_csr(dev, 2, (addr >> 16) & 0xffff);
|
|
|
|
pcnet_write_csr(dev, 4, 0x0915);
|
|
pcnet_write_csr(dev, 0, 0x0001); /* start */
|
|
|
|
/* Wait for Init Done bit */
|
|
for (i = 10000; i > 0; i--) {
|
|
if (pcnet_read_csr(dev, 0) & 0x0100)
|
|
break;
|
|
udelay(10);
|
|
}
|
|
if (i <= 0) {
|
|
printf("%s: TIMEOUT: controller init failed\n", dev->name);
|
|
pcnet_reset(dev);
|
|
return -1;
|
|
}
|
|
|
|
/*
|
|
* Finally start network controller operation.
|
|
*/
|
|
pcnet_write_csr(dev, 0, 0x0002);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int pcnet_send(struct eth_device *dev, void *packet, int pkt_len)
|
|
{
|
|
int i, status;
|
|
struct pcnet_tx_head *entry = &lp->uc->tx_ring[lp->cur_tx];
|
|
|
|
PCNET_DEBUG2("Tx%d: %d bytes from 0x%p ", lp->cur_tx, pkt_len,
|
|
packet);
|
|
|
|
flush_dcache_range((unsigned long)packet,
|
|
(unsigned long)packet + pkt_len);
|
|
|
|
/* Wait for completion by testing the OWN bit */
|
|
for (i = 1000; i > 0; i--) {
|
|
status = readw(&entry->status);
|
|
if ((status & 0x8000) == 0)
|
|
break;
|
|
udelay(100);
|
|
PCNET_DEBUG2(".");
|
|
}
|
|
if (i <= 0) {
|
|
printf("%s: TIMEOUT: Tx%d failed (status = 0x%x)\n",
|
|
dev->name, lp->cur_tx, status);
|
|
pkt_len = 0;
|
|
goto failure;
|
|
}
|
|
|
|
/*
|
|
* Setup Tx ring. Caution: the write order is important here,
|
|
* set the status with the "ownership" bits last.
|
|
*/
|
|
writew(-pkt_len, &entry->length);
|
|
writel(0, &entry->misc);
|
|
writel(PCI_TO_MEM(dev, packet), &entry->base);
|
|
writew(0x8300, &entry->status);
|
|
|
|
/* Trigger an immediate send poll. */
|
|
pcnet_write_csr(dev, 0, 0x0008);
|
|
|
|
failure:
|
|
if (++lp->cur_tx >= TX_RING_SIZE)
|
|
lp->cur_tx = 0;
|
|
|
|
PCNET_DEBUG2("done\n");
|
|
return pkt_len;
|
|
}
|
|
|
|
static int pcnet_recv (struct eth_device *dev)
|
|
{
|
|
struct pcnet_rx_head *entry;
|
|
unsigned char *buf;
|
|
int pkt_len = 0;
|
|
u16 status, err_status;
|
|
|
|
while (1) {
|
|
entry = &lp->uc->rx_ring[lp->cur_rx];
|
|
/*
|
|
* If we own the next entry, it's a new packet. Send it up.
|
|
*/
|
|
status = readw(&entry->status);
|
|
if ((status & 0x8000) != 0)
|
|
break;
|
|
err_status = status >> 8;
|
|
|
|
if (err_status != 0x03) { /* There was an error. */
|
|
printf("%s: Rx%d", dev->name, lp->cur_rx);
|
|
PCNET_DEBUG1(" (status=0x%x)", err_status);
|
|
if (err_status & 0x20)
|
|
printf(" Frame");
|
|
if (err_status & 0x10)
|
|
printf(" Overflow");
|
|
if (err_status & 0x08)
|
|
printf(" CRC");
|
|
if (err_status & 0x04)
|
|
printf(" Fifo");
|
|
printf(" Error\n");
|
|
status &= 0x03ff;
|
|
|
|
} else {
|
|
pkt_len = (readl(&entry->msg_length) & 0xfff) - 4;
|
|
if (pkt_len < 60) {
|
|
printf("%s: Rx%d: invalid packet length %d\n",
|
|
dev->name, lp->cur_rx, pkt_len);
|
|
} else {
|
|
buf = (*lp->rx_buf)[lp->cur_rx];
|
|
invalidate_dcache_range((unsigned long)buf,
|
|
(unsigned long)buf + pkt_len);
|
|
net_process_received_packet(buf, pkt_len);
|
|
PCNET_DEBUG2("Rx%d: %d bytes from 0x%p\n",
|
|
lp->cur_rx, pkt_len, buf);
|
|
}
|
|
}
|
|
|
|
status |= 0x8000;
|
|
writew(status, &entry->status);
|
|
|
|
if (++lp->cur_rx >= RX_RING_SIZE)
|
|
lp->cur_rx = 0;
|
|
}
|
|
return pkt_len;
|
|
}
|
|
|
|
static void pcnet_halt(struct eth_device *dev)
|
|
{
|
|
int i;
|
|
|
|
PCNET_DEBUG1("%s: pcnet_halt...\n", dev->name);
|
|
|
|
/* Reset the PCnet controller */
|
|
pcnet_reset(dev);
|
|
|
|
/* Wait for Stop bit */
|
|
for (i = 1000; i > 0; i--) {
|
|
if (pcnet_read_csr(dev, 0) & 0x4)
|
|
break;
|
|
udelay(10);
|
|
}
|
|
if (i <= 0)
|
|
printf("%s: TIMEOUT: controller reset failed\n", dev->name);
|
|
}
|