mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-13 16:37:30 +00:00
1d6c54ecb3
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot. This patch is adding minimal support to get U-Boot boot. U-Boot on R5 runs out of DDR with default configuration that's why DDR needs to be partitioned if there is something else running on arm64. Console is done via Cadence uart driver and the first Cadence Triple Timer Counter is used for time. This configuration with uart1 was tested on zcu100-revC. U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200) Model: Xilinx ZynqMP R5 DRAM: 512 MiB WARNING: Caches not enabled MMC: In: serial@ff010000 Out: serial@ff010000 Err: serial@ff010000 Net: Net Initialization Skipped No ethernet found. ZynqMP r5> There are two ways how to run this on ZynqMP. 1. Run from ZynqMP arm64 tftpb 20000000 u-boot-r5.elf setenv autostart no && bootelf -p 20000000 cpu 4 disable && cpu 4 release 10000000 lockstep or cpu 4 disable && cpu 4 release 10000000 split 2. Load via jtag when directly to R5 Signed-off-by: Michal Simek <michal.simek@xilinx.com>
685 lines
22 KiB
Text
685 lines
22 KiB
Text
#
|
|
# Serial device configuration
|
|
#
|
|
|
|
menu "Serial drivers"
|
|
|
|
config BAUDRATE
|
|
int "Default baudrate"
|
|
default 115200
|
|
help
|
|
Select a default baudrate, where "default" has a driver-specific
|
|
meaning of either setting the baudrate for the early debug UART
|
|
in the SPL stage (most drivers) or for choosing a default baudrate
|
|
in the absence of an environment setting (serial_mxc.c).
|
|
|
|
config REQUIRE_SERIAL_CONSOLE
|
|
bool "Require a serial port for console"
|
|
# Running without a serial console is not supported by the
|
|
# non-dm serial code
|
|
depends on DM_SERIAL
|
|
default y
|
|
help
|
|
Require a serial port for the console, and panic if none is found
|
|
during serial port initialization (default y). Set this to n on
|
|
boards which have no debug serial port whatsoever.
|
|
|
|
config SPECIFY_CONSOLE_INDEX
|
|
bool "Specify the port number used for console"
|
|
default y if !DM_SERIAL || (SPL && !SPL_DM_SERIAL) || \
|
|
(TPL && !TPL_DM_SERIAL)
|
|
help
|
|
In various cases, we need to specify which of the UART devices that
|
|
a board or SoC has available are to be used for the console device
|
|
in U-Boot.
|
|
|
|
config SERIAL_PRESENT
|
|
bool "Provide a serial driver"
|
|
depends on DM_SERIAL
|
|
default y
|
|
help
|
|
In very space-constrained devices even the full UART driver is too
|
|
large. In this case the debug UART can still be used in some cases.
|
|
This option enables the full UART in U-Boot, so if is it disabled,
|
|
the full UART driver will be omitted, thus saving space.
|
|
|
|
config SPL_SERIAL_PRESENT
|
|
bool "Provide a serial driver in SPL"
|
|
depends on DM_SERIAL
|
|
default y
|
|
help
|
|
In very space-constrained devices even the full UART driver is too
|
|
large. In this case the debug UART can still be used in some cases.
|
|
This option enables the full UART in SPL, so if is it disabled,
|
|
the full UART driver will be omitted, thus saving space.
|
|
|
|
# Logic to allow us to use the imply keyword to set what the default port
|
|
# should be. The default is otherwise 1.
|
|
config CONS_INDEX_0
|
|
bool
|
|
|
|
config CONS_INDEX_2
|
|
bool
|
|
|
|
config CONS_INDEX_3
|
|
bool
|
|
|
|
config CONS_INDEX_4
|
|
bool
|
|
|
|
config CONS_INDEX_5
|
|
bool
|
|
|
|
config CONS_INDEX_6
|
|
bool
|
|
|
|
config CONS_INDEX
|
|
int "UART used for console"
|
|
depends on SPECIFY_CONSOLE_INDEX
|
|
range 0 6
|
|
default 0 if CONS_INDEX_0
|
|
default 2 if CONS_INDEX_2
|
|
default 3 if CONS_INDEX_3
|
|
default 4 if CONS_INDEX_4
|
|
default 5 if CONS_INDEX_5
|
|
default 6 if CONS_INDEX_6
|
|
default 1
|
|
help
|
|
Set this to match the UART number of the serial console.
|
|
|
|
config DM_SERIAL
|
|
bool "Enable Driver Model for serial drivers"
|
|
depends on DM
|
|
help
|
|
Enable driver model for serial. This replaces
|
|
drivers/serial/serial.c with the serial uclass, which
|
|
implements serial_putc() etc. The uclass interface is
|
|
defined in include/serial.h.
|
|
|
|
config SERIAL_RX_BUFFER
|
|
bool "Enable RX buffer for serial input"
|
|
depends on DM_SERIAL
|
|
help
|
|
Enable RX buffer support for the serial driver. This enables
|
|
pasting longer strings, even when the RX FIFO of the UART is
|
|
not big enough (e.g. 16 bytes on the normal NS16550).
|
|
|
|
config SERIAL_RX_BUFFER_SIZE
|
|
int "RX buffer size"
|
|
depends on SERIAL_RX_BUFFER
|
|
default 256
|
|
help
|
|
The size of the RX buffer (needs to be power of 2)
|
|
|
|
config SERIAL_SEARCH_ALL
|
|
bool "Search for serial devices after default one failed"
|
|
depends on DM_SERIAL
|
|
help
|
|
The serial subsystem only searches for a single serial device
|
|
that was instantiated, but does not check whether it was probed
|
|
correctly. With this option set, we make successful probing
|
|
mandatory and search for fallback serial devices if the default
|
|
device does not work.
|
|
|
|
If unsure, say N.
|
|
|
|
config SPL_DM_SERIAL
|
|
bool "Enable Driver Model for serial drivers in SPL"
|
|
depends on DM_SERIAL && SPL_DM
|
|
default y
|
|
help
|
|
Enable driver model for serial in SPL. This replaces
|
|
drivers/serial/serial.c with the serial uclass, which
|
|
implements serial_putc() etc. The uclass interface is
|
|
defined in include/serial.h.
|
|
|
|
config TPL_DM_SERIAL
|
|
bool "Enable Driver Model for serial drivers in TPL"
|
|
depends on DM_SERIAL
|
|
default y if TPL && DM_SERIAL
|
|
help
|
|
Enable driver model for serial in TPL. This replaces
|
|
drivers/serial/serial.c with the serial uclass, which
|
|
implements serial_putc() etc. The uclass interface is
|
|
defined in include/serial.h.
|
|
|
|
config DEBUG_UART
|
|
bool "Enable an early debug UART for debugging"
|
|
help
|
|
The debug UART is intended for use very early in U-Boot to debug
|
|
problems when an ICE or other debug mechanism is not available.
|
|
|
|
To use it you should:
|
|
- Make sure your UART supports this interface
|
|
- Enable CONFIG_DEBUG_UART
|
|
- Enable the CONFIG for your UART to tell it to provide this interface
|
|
(e.g. CONFIG_DEBUG_UART_NS16550)
|
|
- Define the required settings as needed (see below)
|
|
- Call debug_uart_init() before use
|
|
- Call debug_uart_putc() to output a character
|
|
|
|
Depending on your platform it may be possible to use this UART before
|
|
a stack is available.
|
|
|
|
If your UART does not support this interface you can probably add
|
|
support quite easily. Remember that you cannot use driver model and
|
|
it is preferred to use no stack.
|
|
|
|
You must not use this UART once driver model is working and the
|
|
serial drivers are up and running (done in serial_init()). Otherwise
|
|
the drivers may conflict and you will get strange output.
|
|
|
|
choice
|
|
prompt "Select which UART will provide the debug UART"
|
|
depends on DEBUG_UART
|
|
default DEBUG_UART_NS16550
|
|
|
|
config DEBUG_UART_ALTERA_JTAGUART
|
|
bool "Altera JTAG UART"
|
|
help
|
|
Select this to enable a debug UART using the altera_jtag_uart driver.
|
|
You will need to provide parameters to make this work. The driver will
|
|
be available until the real driver model serial is running.
|
|
|
|
config DEBUG_UART_ALTERA_UART
|
|
bool "Altera UART"
|
|
help
|
|
Select this to enable a debug UART using the altera_uart driver.
|
|
You will need to provide parameters to make this work. The driver will
|
|
be available until the real driver model serial is running.
|
|
|
|
config DEBUG_UART_AR933X
|
|
bool "QCA/Atheros ar933x"
|
|
depends on AR933X_UART
|
|
help
|
|
Select this to enable a debug UART using the ar933x uart driver.
|
|
You will need to provide parameters to make this work. The
|
|
driver will be available until the real driver model serial is
|
|
running.
|
|
|
|
config DEBUG_UART_ATMEL
|
|
bool "Atmel USART"
|
|
help
|
|
Select this to enable a debug UART using the atmel usart driver. You
|
|
will need to provide parameters to make this work. The driver will
|
|
be available until the real driver-model serial is running.
|
|
|
|
config DEBUG_UART_BCM6345
|
|
bool "BCM6345 UART"
|
|
depends on BCM6345_SERIAL
|
|
help
|
|
Select this to enable a debug UART on BCM6345 SoCs. You
|
|
will need to provide parameters to make this work. The driver will
|
|
be available until the real driver model serial is running.
|
|
|
|
config DEBUG_UART_NS16550
|
|
bool "ns16550"
|
|
help
|
|
Select this to enable a debug UART using the ns16550 driver. You
|
|
will need to provide parameters to make this work. The driver will
|
|
be available until the real driver model serial is running.
|
|
|
|
config DEBUG_EFI_CONSOLE
|
|
bool "EFI"
|
|
depends on EFI_APP
|
|
help
|
|
Select this to enable a debug console which calls back to EFI to
|
|
output to the console. This can be useful for early debugging of
|
|
U-Boot when running on top of EFI (Extensive Firmware Interface).
|
|
This is a type of BIOS used by PCs.
|
|
|
|
config DEBUG_UART_S5P
|
|
bool "Samsung S5P"
|
|
help
|
|
Select this to enable a debug UART using the serial_s5p driver. You
|
|
will need to provide parameters to make this work. The driver will
|
|
be available until the real driver-model serial is running.
|
|
|
|
config DEBUG_UART_MESON
|
|
bool "Amlogic Meson"
|
|
depends on MESON_SERIAL
|
|
help
|
|
Select this to enable a debug UART using the serial_meson driver. You
|
|
will need to provide parameters to make this work. The driver will
|
|
be available until the real driver-model serial is running.
|
|
|
|
config DEBUG_UART_UARTLITE
|
|
bool "Xilinx Uartlite"
|
|
help
|
|
Select this to enable a debug UART using the serial_uartlite driver.
|
|
You will need to provide parameters to make this work. The driver will
|
|
be available until the real driver-model serial is running.
|
|
|
|
config DEBUG_UART_ARM_DCC
|
|
bool "ARM DCC"
|
|
help
|
|
Select this to enable a debug UART using the ARM JTAG DCC port.
|
|
The DCC port can be used for very early debugging and doesn't require
|
|
any additional setting like address/baudrate/clock. On systems without
|
|
any serial interface this is the easiest way how to get console.
|
|
Every ARM core has own DCC port which is the part of debug interface.
|
|
This port is available at least on ARMv6, ARMv7, ARMv8 and XScale
|
|
architectures.
|
|
|
|
config DEBUG_MVEBU_A3700_UART
|
|
bool "Marvell Armada 3700"
|
|
help
|
|
Select this to enable a debug UART using the serial_mvebu driver. You
|
|
will need to provide parameters to make this work. The driver will
|
|
be available until the real driver-model serial is running.
|
|
|
|
config DEBUG_UART_ZYNQ
|
|
bool "Xilinx Zynq"
|
|
help
|
|
Select this to enable a debug UART using the serial_zynq driver. You
|
|
will need to provide parameters to make this work. The driver will
|
|
be available until the real driver-model serial is running.
|
|
|
|
config DEBUG_UART_APBUART
|
|
depends on LEON3
|
|
bool "Gaisler APBUART"
|
|
help
|
|
Select this to enable a debug UART using the serial_leon3 driver. You
|
|
will need to provide parameters to make this work. The driver will
|
|
be available until the real driver model serial is running.
|
|
|
|
config DEBUG_UART_PL010
|
|
bool "pl010"
|
|
help
|
|
Select this to enable a debug UART using the pl01x driver with the
|
|
PL010 UART type. You will need to provide parameters to make this
|
|
work. The driver will be available until the real driver model
|
|
serial is running.
|
|
|
|
config DEBUG_UART_PL011
|
|
bool "pl011"
|
|
help
|
|
Select this to enable a debug UART using the pl01x driver with the
|
|
PL011 UART type. You will need to provide parameters to make this
|
|
work. The driver will be available until the real driver model
|
|
serial is running.
|
|
|
|
config DEBUG_UART_PIC32
|
|
bool "Microchip PIC32"
|
|
depends on PIC32_SERIAL
|
|
help
|
|
Select this to enable a debug UART using the serial_pic32 driver. You
|
|
will need to provide parameters to make this work. The driver will
|
|
be available until the real driver model serial is running.
|
|
|
|
config DEBUG_UART_MXC
|
|
bool "IMX Serial port"
|
|
depends on MXC_UART
|
|
help
|
|
Select this to enable a debug UART using the serial_mxc driver. You
|
|
will need to provide parameters to make this work. The driver will
|
|
be available until the real driver model serial is running.
|
|
|
|
config DEBUG_UART_UNIPHIER
|
|
bool "UniPhier on-chip UART"
|
|
depends on ARCH_UNIPHIER
|
|
help
|
|
Select this to enable a debug UART using the UniPhier on-chip UART.
|
|
You will need to provide DEBUG_UART_BASE to make this work. The
|
|
driver will be available until the real driver-model serial is
|
|
running.
|
|
|
|
config DEBUG_UART_OMAP
|
|
bool "OMAP uart"
|
|
help
|
|
Select this to enable a debug UART using the omap ns16550 driver.
|
|
You will need to provide parameters to make this work. The driver
|
|
will be available until the real driver model serial is running.
|
|
|
|
endchoice
|
|
|
|
config DEBUG_UART_BASE
|
|
hex "Base address of UART"
|
|
depends on DEBUG_UART
|
|
help
|
|
This is the base address of your UART for memory-mapped UARTs.
|
|
|
|
A default should be provided by your board, but if not you will need
|
|
to use the correct value here.
|
|
|
|
config DEBUG_UART_CLOCK
|
|
int "UART input clock"
|
|
depends on DEBUG_UART
|
|
help
|
|
The UART input clock determines the speed of the internal UART
|
|
circuitry. The baud rate is derived from this by dividing the input
|
|
clock down.
|
|
|
|
A default should be provided by your board, but if not you will need
|
|
to use the correct value here.
|
|
|
|
config DEBUG_UART_SHIFT
|
|
int "UART register shift"
|
|
depends on DEBUG_UART
|
|
default 0 if DEBUG_UART
|
|
help
|
|
Some UARTs (notably ns16550) support different register layouts
|
|
where the registers are spaced either as bytes, words or some other
|
|
value. Use this value to specify the shift to use, where 0=byte
|
|
registers, 2=32-bit word registers, etc.
|
|
|
|
config DEBUG_UART_BOARD_INIT
|
|
bool "Enable board-specific debug UART init"
|
|
depends on DEBUG_UART
|
|
help
|
|
Some boards need to set things up before the debug UART can be used.
|
|
On these boards a call to debug_uart_init() is insufficient. When
|
|
this option is enabled, the function board_debug_uart_init() will
|
|
be called when debug_uart_init() is called. You can put any code
|
|
here that is needed to set up the UART ready for use, such as set
|
|
pin multiplexing or enable clocks.
|
|
|
|
config DEBUG_UART_ANNOUNCE
|
|
bool "Show a message when the debug UART starts up"
|
|
depends on DEBUG_UART
|
|
help
|
|
Enable this option to show a message when the debug UART is ready
|
|
for use. You will see a message like "<debug_uart> " as soon as
|
|
U-Boot has the UART ready for use (i.e. your code calls
|
|
debug_uart_init()). This can be useful just as a check that
|
|
everything is working.
|
|
|
|
config DEBUG_UART_SKIP_INIT
|
|
bool "Skip UART initialization"
|
|
help
|
|
Select this if the UART you want to use for debug output is already
|
|
initialized by the time U-Boot starts its execution.
|
|
|
|
config ALTERA_JTAG_UART
|
|
bool "Altera JTAG UART support"
|
|
depends on DM_SERIAL
|
|
help
|
|
Select this to enable an JTAG UART for Altera devices.The JTAG UART
|
|
core implements a method to communicate serial character streams
|
|
between a host PC and a Qsys system on an Altera FPGA. Please find
|
|
details on the "Embedded Peripherals IP User Guide" of Altera.
|
|
|
|
config ALTERA_JTAG_UART_BYPASS
|
|
bool "Bypass output when no connection"
|
|
depends on ALTERA_JTAG_UART
|
|
help
|
|
Bypass console output and keep going even if there is no JTAG
|
|
terminal connection with the host. The console output will resume
|
|
once the JTAG terminal is connected. Without the bypass, the console
|
|
output will wait forever until a JTAG terminal is connected. If you
|
|
not are sure, say Y.
|
|
|
|
config ALTERA_UART
|
|
bool "Altera UART support"
|
|
depends on DM_SERIAL
|
|
help
|
|
Select this to enable an UART for Altera devices. Please find
|
|
details on the "Embedded Peripherals IP User Guide" of Altera.
|
|
|
|
config AR933X_UART
|
|
bool "QCA/Atheros ar933x UART support"
|
|
depends on DM_SERIAL && SOC_AR933X
|
|
help
|
|
Select this to enable UART support for QCA/Atheros ar933x
|
|
devices. This driver uses driver model and requires a device
|
|
tree binding to operate, please refer to the document at
|
|
doc/device-tree-bindings/serial/qca,ar9330-uart.txt.
|
|
|
|
config ATMEL_USART
|
|
bool "Atmel USART support"
|
|
help
|
|
Select this to enable USART support for Atmel SoCs. It can be
|
|
configured in the device tree, and input clock frequency can
|
|
be got from the clk node.
|
|
|
|
config BCM283X_MU_SERIAL
|
|
bool "Support for BCM283x Mini-UART"
|
|
depends on DM_SERIAL && ARCH_BCM283X
|
|
default y
|
|
help
|
|
Select this to enable Mini-UART support on BCM283X family of SoCs.
|
|
|
|
config BCM283X_PL011_SERIAL
|
|
bool "Support for BCM283x PL011 UART"
|
|
depends on PL01X_SERIAL && ARCH_BCM283X
|
|
default y
|
|
help
|
|
Select this to enable an overriding PL011 driver for BCM283X SoCs
|
|
that supports automatic disable, so that it only gets used when
|
|
the UART is actually muxed.
|
|
|
|
config BCM6345_SERIAL
|
|
bool "Support for BCM6345 UART"
|
|
depends on DM_SERIAL && ARCH_BMIPS
|
|
help
|
|
Select this to enable UART on BCM6345 SoCs.
|
|
|
|
config FSL_LINFLEXUART
|
|
bool "Freescale Linflex UART support"
|
|
depends on DM_SERIAL
|
|
help
|
|
Select this to enable the Linflex serial module found on some
|
|
NXP SoCs like S32V234.
|
|
|
|
config FSL_LPUART
|
|
bool "Freescale LPUART support"
|
|
help
|
|
Select this to enable a Low Power UART for Freescale VF610 and
|
|
QorIQ Layerscape devices.
|
|
|
|
config MVEBU_A3700_UART
|
|
bool "UART support for Armada 3700"
|
|
default n
|
|
help
|
|
Choose this option to add support for UART driver on the Marvell
|
|
Armada 3700 SoC. The base address is configured via DT.
|
|
|
|
config MXC_UART
|
|
bool "IMX serial port support"
|
|
depends on MX5 || MX6
|
|
help
|
|
If you have a machine based on a Motorola IMX CPU you
|
|
can enable its onboard serial port by enabling this option.
|
|
|
|
config NULLDEV_SERIAL
|
|
bool "Null serial device"
|
|
help
|
|
Select this to enable null serial device support. A null serial
|
|
device merely acts as a placeholder for a serial device and does
|
|
nothing for all it's operation.
|
|
|
|
config PIC32_SERIAL
|
|
bool "Support for Microchip PIC32 on-chip UART"
|
|
depends on DM_SERIAL && MACH_PIC32
|
|
default y
|
|
help
|
|
Support for the UART found on Microchip PIC32 SoC's.
|
|
|
|
config SYS_NS16550
|
|
bool "NS16550 UART or compatible"
|
|
help
|
|
Support NS16550 UART or compatible. This can be enabled in the
|
|
device tree with the correct input clock frequency. If the input
|
|
clock frequency is not defined in the device tree, the macro
|
|
CONFIG_SYS_NS16550_CLK defined in a legacy board header file will
|
|
be used. It can be a constant or a function to get clock, eg,
|
|
get_serial_clock().
|
|
|
|
config INTEL_MID_SERIAL
|
|
bool "Intel MID platform UART support"
|
|
depends on DM_SERIAL && OF_CONTROL
|
|
depends on INTEL_MID
|
|
select SYS_NS16550
|
|
help
|
|
Select this to enable a UART for Intel MID platforms.
|
|
This uses the ns16550 driver as a library.
|
|
|
|
config PL010_SERIAL
|
|
bool "ARM PL010 driver"
|
|
depends on !DM_SERIAL
|
|
help
|
|
Select this to enable a UART for platforms using PL010.
|
|
|
|
config PL011_SERIAL
|
|
bool "ARM PL011 driver"
|
|
depends on !DM_SERIAL
|
|
help
|
|
Select this to enable a UART for platforms using PL011.
|
|
|
|
config PL01X_SERIAL
|
|
bool "ARM PL010 and PL011 driver"
|
|
depends on DM_SERIAL
|
|
help
|
|
Select this to enable a UART for platforms using PL010 or PL011.
|
|
|
|
config ROCKCHIP_SERIAL
|
|
bool "Rockchip on-chip UART support"
|
|
depends on DM_SERIAL && SPL_OF_PLATDATA
|
|
help
|
|
Select this to enable a debug UART for Rockchip devices when using
|
|
CONFIG_SPL_OF_PLATDATA (i.e. a compiled-in device tree replacemenmt).
|
|
This uses the ns16550 driver, converting the platdata from of-platdata
|
|
to the ns16550 format.
|
|
|
|
config SANDBOX_SERIAL
|
|
bool "Sandbox UART support"
|
|
depends on SANDBOX
|
|
help
|
|
Select this to enable a seral UART for sandbox. This is required to
|
|
operate correctly, otherwise you will see no serial output from
|
|
sandbox. The emulated UART will display to the console and console
|
|
input will be fed into the UART. This allows you to interact with
|
|
U-Boot.
|
|
|
|
The operation of the console is controlled by the -t command-line
|
|
flag. In raw mode, U-Boot sees all characters from the terminal
|
|
before they are processed, including Ctrl-C. In cooked mode, Ctrl-C
|
|
is processed by the terminal, and terminates U-Boot. Valid options
|
|
are:
|
|
|
|
-t raw-with-sigs Raw mode, Ctrl-C will terminate U-Boot
|
|
-t raw Raw mode, Ctrl-C is processed by U-Boot
|
|
-t cooked Cooked mode, Ctrl-C terminates
|
|
|
|
config SCIF_CONSOLE
|
|
bool "Renesas SCIF UART support"
|
|
depends on SH || ARCH_RMOBILE
|
|
help
|
|
Select this to enable Renesas SCIF UART. To operate serial ports
|
|
on systems with RCar or SH SoCs, say Y to this option. If unsure,
|
|
say N.
|
|
|
|
config UNIPHIER_SERIAL
|
|
bool "Support for UniPhier on-chip UART"
|
|
depends on ARCH_UNIPHIER
|
|
default y
|
|
help
|
|
If you have a UniPhier based board and want to use the on-chip
|
|
serial ports, say Y to this option. If unsure, say N.
|
|
|
|
config XILINX_UARTLITE
|
|
bool "Xilinx Uarlite support"
|
|
depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || 4xx)
|
|
help
|
|
If you have a Xilinx based board and want to use the uartlite
|
|
serial ports, say Y to this option. If unsure, say N.
|
|
|
|
config MESON_SERIAL
|
|
bool "Support for Amlogic Meson UART"
|
|
depends on DM_SERIAL && ARCH_MESON
|
|
help
|
|
If you have an Amlogic Meson based board and want to use the on-chip
|
|
serial ports, say Y to this option. If unsure, say N.
|
|
|
|
config MSM_SERIAL
|
|
bool "Qualcomm on-chip UART"
|
|
depends on DM_SERIAL
|
|
help
|
|
Support Data Mover UART used on Qualcomm Snapdragon SoCs.
|
|
It should support all Qualcomm devices with UARTDM version 1.4,
|
|
for example APQ8016 and MSM8916.
|
|
Single baudrate is supported in current implementation (115200).
|
|
|
|
config PXA_SERIAL
|
|
bool "PXA serial port support"
|
|
help
|
|
If you have a machine based on a Marvell XScale PXA2xx CPU you
|
|
can enable its onboard serial ports by enabling this option.
|
|
|
|
config STI_ASC_SERIAL
|
|
bool "STMicroelectronics on-chip UART"
|
|
depends on DM_SERIAL && ARCH_STI
|
|
help
|
|
Select this to enable Asynchronous Serial Controller available
|
|
on STiH410 SoC. This is a basic implementation, it supports
|
|
following baudrate 9600, 19200, 38400, 57600 and 115200.
|
|
|
|
config STM32_SERIAL
|
|
bool "STMicroelectronics STM32 SoCs on-chip UART"
|
|
depends on DM_SERIAL && (STM32F4 || STM32F7 || STM32H7 || ARCH_STM32MP)
|
|
help
|
|
If you have a machine based on a STM32 F4, F7, H7 or MP1 SOC
|
|
you can enable its onboard serial ports, say Y to this option.
|
|
If unsure, say N.
|
|
|
|
config ZYNQ_SERIAL
|
|
bool "Cadence (Xilinx Zynq) UART support"
|
|
depends on DM_SERIAL && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || ARCH_ZYNQMP_R5)
|
|
help
|
|
This driver supports the Cadence UART. It is found e.g. in Xilinx
|
|
Zynq/ZynqMP.
|
|
|
|
config MPC8XX_CONS
|
|
bool "Console driver for MPC8XX"
|
|
depends on MPC8xx
|
|
default y
|
|
|
|
choice
|
|
prompt "Console port"
|
|
default 8xx_CONS_SMC1
|
|
depends on MPC8XX_CONS
|
|
help
|
|
Depending on board, select one serial port
|
|
(CONFIG_8xx_CONS_SMC1 or CONFIG_8xx_CONS_SMC2)
|
|
|
|
config 8xx_CONS_SMC1
|
|
bool "SMC1"
|
|
|
|
config 8xx_CONS_SMC2
|
|
bool "SMC2"
|
|
|
|
endchoice
|
|
|
|
config SYS_SMC_RXBUFLEN
|
|
int "Console Rx buffer length"
|
|
depends on MPC8XX_CONS
|
|
default 1
|
|
help
|
|
With CONFIG_SYS_SMC_RXBUFLEN it is possible to define
|
|
the maximum receive buffer length for the SMC.
|
|
This option is actual only for 8xx possible.
|
|
If using CONFIG_SYS_SMC_RXBUFLEN also CONFIG_SYS_MAXIDLE
|
|
must be defined, to setup the maximum idle timeout for
|
|
the SMC.
|
|
|
|
config SYS_MAXIDLE
|
|
int "maximum idle timeout"
|
|
depends on MPC8XX_CONS
|
|
default 0
|
|
|
|
config SYS_BRGCLK_PRESCALE
|
|
int "BRG Clock Prescale"
|
|
depends on MPC8XX_CONS
|
|
default 1
|
|
|
|
config SYS_SDSR
|
|
hex "SDSR Value"
|
|
depends on MPC8XX_CONS
|
|
default 0x83
|
|
|
|
config SYS_SDMR
|
|
hex "SDMR Value"
|
|
depends on MPC8XX_CONS
|
|
default 0
|
|
|
|
endmenu
|