u-boot/include/configs/qi_lb60.h
Xiangfu Liu 3c945542da MIPS: Jz4740: Add qi_lb60 board support
Add support for the qi_lb60 (a.k.a QI Ben NanoNote) clamshell device
from Qi hardware:

http://en.qi-hardware.com/wiki/Ben_NanoNote
http://en.qi-hardware.com/wiki/Main_Page
http://en.wikipedia.org/wiki/Qi_hardware

This Jz4740-based clamshell device does not use NOR flash to boot.
The initial bring-up assumes that U-Boot is directly loaded into SDRAM
using USB boot tool, and starts from 0x80100000.

About USB boot tool
-------------------

Jz4740 is one of the XBurst processors with USB boot functionality
supported.  The CPU can boot from a small ROM in the LSI, initialize
CPU and USB module, then wait for USB commands from the USB host.
We can send 8 KB binary data to the CPU cache using USB boot tool.

USB boot tool is available to the public at Ingenic website.  Also
there is an alternative Debian package named xburst-tools.

Signed-off-by: Xiangfu Liu <xiangfu@openmobilefree.net>
Acked-by: Daniel <zpxu@ingenic.cn>
Signed-off-by: Shinya Kuribayashi <skuribay@pobox.com>
2011-10-12 23:28:49 +09:00

211 lines
7.1 KiB
C

/*
* Authors: Xiangfu Liu <xiangfu.z@gmail.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 3 of the License, or (at your option) any later version.
*/
#ifndef __CONFIG_QI_LB60_H
#define __CONFIG_QI_LB60_H
#define CONFIG_MIPS32 /* MIPS32 CPU core */
#define CONFIG_JZSOC /* Jz SoC */
#define CONFIG_JZ4740 /* Jz4740 SoC */
#define CONFIG_NAND_JZ4740
#define CONFIG_SYS_CPU_SPEED 336000000 /* CPU clock: 336 MHz */
#define CONFIG_SYS_EXTAL 12000000 /* EXTAL freq: 12 MHz */
#define CONFIG_SYS_HZ (CONFIG_SYS_EXTAL / 256) /* incrementer freq */
#define CONFIG_SYS_MIPS_TIMER_FREQ CONFIG_SYS_CPU_SPEED
#define CONFIG_SYS_UART_BASE JZ4740_UART0_BASE /* Base of the UART channel */
#define CONFIG_BAUDRATE 57600
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_SYS_NO_FLASH
#define CONFIG_SYS_FLASH_BASE 0 /* init flash_base as 0 */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_BOOTP_MASK (CONFIG_BOOTP_DEFAUL)
#define CONFIG_BOOTDELAY 0
#define CONFIG_BOOTARGS "mem=32M console=tty0 console=ttyS0,57600n8 ubi.mtd=2 rootfstype=ubifs root=ubi0:rootfs rw rootwait"
#define CONFIG_BOOTCOMMAND "nand read 0x80600000 0x400000 0x200000;bootm"
/*
* Command line configuration.
*/
#define CONFIG_CMD_BOOTD /* bootd */
#define CONFIG_CMD_CONSOLE /* coninfo */
#define CONFIG_CMD_ECHO /* echo arguments */
#define CONFIG_CMD_LOADB /* loadb */
#define CONFIG_CMD_LOADS /* loads */
#define CONFIG_CMD_MEMORY /* md mm nm mw cp cmp crc base loop mtest */
#define CONFIG_CMD_MISC /* Misc functions like sleep etc*/
#define CONFIG_CMD_RUN /* run command in env variable */
#define CONFIG_CMD_SAVEENV /* saveenv */
#define CONFIG_CMD_SETGETDCR /* DCR support on 4xx */
#define CONFIG_CMD_SOURCE /* "source" command support */
#define CONFIG_CMD_NAND
/*
* Serial download configuration
*/
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_PROMPT "NanoNote# "
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MALLOC_LEN (4 * 1024 * 1024)
#define CONFIG_SYS_BOOTPARAMS_LEN (128 * 1024)
#define CONFIG_SYS_SDRAM_BASE 0x80000000 /* Cached addr */
#define CONFIG_SYS_INIT_SP_OFFSET 0x400000
#define CONFIG_SYS_LOAD_ADDR 0x80600000
#define CONFIG_SYS_MEMTEST_START 0x80100000
#define CONFIG_SYS_MEMTEST_END 0x80800000
/*
* Environment
*/
#define CONFIG_ENV_IS_IN_NAND /* use NAND for environment vars */
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
/*
* if board nand flash is 1GB, set to 1
* if board nand flash is 2GB, set to 2
* for change the PAGE_SIZE and BLOCK_SIZE
* will delete when there is no 1GB flash
*/
#define NANONOTE_NAND_SIZE 2
#define CONFIG_SYS_NAND_PAGE_SIZE (2048 * NANONOTE_NAND_SIZE)
#define CONFIG_SYS_NAND_BLOCK_SIZE (256 * NANONOTE_NAND_SIZE << 10)
/* nand bad block was marked at this page in a block, start from 0 */
#define CONFIG_SYS_NAND_BADBLOCK_PAGE 127
#define CONFIG_SYS_NAND_PAGE_COUNT 128
#define CONFIG_SYS_NAND_BAD_BLOCK_POS 0
/* ECC offset position in oob area, default value is 6 if it isn't defined */
#define CONFIG_SYS_NAND_ECC_POS (6 * NANONOTE_NAND_SIZE)
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 9
#define CONFIG_SYS_NAND_ECCSTEPS \
(CONFIG_SYS_NAND_PAGE_SIZE / CONFIG_SYS_NAND_ECCSIZE)
#define CONFIG_SYS_NAND_ECCTOTAL \
(CONFIG_SYS_NAND_ECCBYTES * CONFIG_SYS_NAND_ECCSTEPS)
#define CONFIG_SYS_NAND_ECCPOS \
{12, 13, 14, 15, 16, 17, 18, 19,\
20, 21, 22, 23, 24, 25, 26, 27, \
28, 29, 30, 31, 32, 33, 34, 35, \
36, 37, 38, 39, 40, 41, 42, 43, \
44, 45, 46, 47, 48, 49, 50, 51, \
52, 53, 54, 55, 56, 57, 58, 59, \
60, 61, 62, 63, 64, 65, 66, 67, \
68, 69, 70, 71, 72, 73, 74, 75, \
76, 77, 78, 79, 80, 81, 82, 83}
#define CONFIG_SYS_NAND_OOBSIZE 128
#define CONFIG_SYS_NAND_BASE 0xB8000000
#define CONFIG_SYS_ONENAND_BASE CONFIG_SYS_NAND_BASE
#define NAND_MAX_CHIPS 1
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_SELECT_DEVICE 1 /* nand driver supports mutipl.*/
#define CONFIG_NAND_SPL_TEXT_BASE 0x80000000
/*
* IPL (Initial Program Loader, integrated inside CPU)
* Will load first 8k from NAND (SPL) into cache and execute it from there.
*
* SPL (Secondary Program Loader)
* Will load special U-Boot version (NUB) from NAND and execute it. This SPL
* has to fit into 8kByte. It sets up the CPU and configures the SDRAM
* controller and the NAND controller so that the special U-Boot image can be
* loaded from NAND to SDRAM.
*
* NUB (NAND U-Boot)
* This NAND U-Boot (NUB) is a special U-Boot version which can be started
* from RAM. Therefore it mustn't (re-)configure the SDRAM controller.
*
*/
#define CONFIG_SYS_NAND_U_BOOT_DST 0x80100000 /* Load NUB to this addr */
#define CONFIG_SYS_NAND_U_BOOT_START CONFIG_SYS_NAND_U_BOOT_DST
/* Start NUB from this addr*/
/*
* Define the partitioning of the NAND chip (only RAM U-Boot is needed here)
*/
#define CONFIG_SYS_NAND_U_BOOT_OFFS (256 << 10) /* Offset to RAM U-Boot image */
#define CONFIG_SYS_NAND_U_BOOT_SIZE (512 << 10) /* Size of RAM U-Boot image */
#define CONFIG_ENV_SIZE (4 << 10)
#define CONFIG_ENV_OFFSET \
(CONFIG_SYS_NAND_BLOCK_SIZE + CONFIG_SYS_NAND_U_BOOT_SIZE)
#define CONFIG_ENV_OFFSET_REDUND \
(CONFIG_ENV_OFFSET + CONFIG_SYS_NAND_BLOCK_SIZE)
#define CONFIG_SYS_TEXT_BASE 0x80100000
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
/*
* SDRAM Info.
*/
#define CONFIG_NR_DRAM_BANKS 1
/*
* Cache Configuration
*/
#define CONFIG_SYS_DCACHE_SIZE 16384
#define CONFIG_SYS_ICACHE_SIZE 16384
#define CONFIG_SYS_CACHELINE_SIZE 32
/*
* GPIO definition
*/
#define GPIO_LCD_CS (2 * 32 + 21)
#define GPIO_AMP_EN (3 * 32 + 4)
#define GPIO_SDPW_EN (3 * 32 + 2)
#define GPIO_SD_DETECT (3 * 32 + 0)
#define GPIO_BUZZ_PWM (3 * 32 + 27)
#define GPIO_USB_DETECT (3 * 32 + 28)
#define GPIO_AUDIO_POP (1 * 32 + 29)
#define GPIO_COB_TEST (1 * 32 + 30)
#define GPIO_KEYOUT_BASE (2 * 32 + 10)
#define GPIO_KEYIN_BASE (3 * 32 + 18)
#define GPIO_KEYIN_8 (3 * 32 + 26)
#define GPIO_SD_CD_N GPIO_SD_DETECT /* SD Card insert detect */
#define GPIO_SD_VCC_EN_N GPIO_SDPW_EN /* SD Card Power Enable */
#define SPEN GPIO_LCD_CS /* LCDCS :Serial command enable */
#define SPDA (2 * 32 + 22) /* LCDSCL:Serial command clock input */
#define SPCK (2 * 32 + 23) /* LCDSDA:Serial command data input */
/* SDRAM paramters */
#define SDRAM_BW16 1 /* Data bus width: 0-32bit, 1-16bit */
#define SDRAM_BANK4 1 /* Banks each chip: 0-2bank, 1-4bank */
#define SDRAM_ROW 13 /* Row address: 11 to 13 */
#define SDRAM_COL 9 /* Column address: 8 to 12 */
#define SDRAM_CASL 2 /* CAS latency: 2 or 3 */
/* SDRAM Timings, unit: ns */
#define SDRAM_TRAS 45 /* RAS# Active Time */
#define SDRAM_RCD 20 /* RAS# to CAS# Delay */
#define SDRAM_TPC 20 /* RAS# Precharge Time */
#define SDRAM_TRWL 7 /* Write Latency Time */
#define SDRAM_TREF 15625 /* Refresh period: 8192 cycles/64ms */
#endif