mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-07 05:34:28 +00:00
a05eb8b14a
The 'enable-active-high' DTS property configures GPIO so it is active with HIGH state (by default it is low). The 'regulator-boot-on' property indicates that the regulator was enabled in the 'earlier' stage - i.e. bootloader/firmware. In the XEA case the 'fec-3v3' was configured (as a "wrapper" on GPIO0_0) in very early SPL code, so it shouldn't be modified at latter stages. Signed-off-by: Lukasz Majewski <lukma@denx.de>
112 lines
2.1 KiB
Text
112 lines
2.1 KiB
Text
// SPDX-License-Identifier: GPL-2.0+
|
|
/*
|
|
* Copyright 2019
|
|
* Lukasz Majewski, DENX Software Engineering, lukma@denx.de
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+ or X11
|
|
*
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include "imx28.dtsi"
|
|
|
|
/ {
|
|
model = "Liebherr (LWE) XEA i.MX28 Board";
|
|
compatible = "lwe,xea", "fsl,imx28";
|
|
|
|
aliases {
|
|
spi3 = &ssp3;
|
|
};
|
|
|
|
memory@40000000 {
|
|
device_type = "memory";
|
|
reg = <0x40000000 0x10000000>;
|
|
};
|
|
|
|
reg_3p3v: regulator-3p3v {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "3P3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
};
|
|
|
|
reg_fec_3v3: regulator-fec-3v3 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "fec-3v3";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
gpio = <&gpio0 0 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
regulator-boot-on;
|
|
};
|
|
};
|
|
|
|
&mac0 {
|
|
phy-mode = "rmii";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mac0_pins_a>;
|
|
phy-supply = <®_fec_3v3>;
|
|
phy-reset-gpios = <&gpio2 13 GPIO_ACTIVE_LOW>;
|
|
phy-reset-duration = <1>;
|
|
phy-reset-post-delay = <1>;
|
|
status = "okay";
|
|
|
|
fixed-link {
|
|
speed = <100>;
|
|
full-duplex;
|
|
};
|
|
};
|
|
|
|
&ssp0 {
|
|
compatible = "fsl,imx28-mmc";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&mmc0_8bit_pins_a>;
|
|
bus-width = <8>;
|
|
vmmc-supply = <®_3p3v>;
|
|
non-removable;
|
|
status = "okay";
|
|
};
|
|
|
|
&ssp3 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
compatible = "fsl,imx28-spi";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&spi3_pins_b>;
|
|
status = "okay";
|
|
spi-max-frequency = <40000000>;
|
|
num-cs = <2>;
|
|
|
|
flash0: s25fl256s@0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "jedec,spi-nor";
|
|
spi-max-frequency = <40000000>;
|
|
reg = <0>;
|
|
|
|
partition@0 {
|
|
label = "SPL (spi)";
|
|
reg = <0x0 0x10000>;
|
|
read-only;
|
|
};
|
|
partition@1 {
|
|
label = "u-boot (spi)";
|
|
reg = <0x10000 0x70000>;
|
|
read-only;
|
|
};
|
|
partition@2 {
|
|
label = "uboot-env (spi)";
|
|
reg = <0x80000 0x20000>;
|
|
};
|
|
partition@3 {
|
|
label = "kernel (spi)";
|
|
reg = <0x100000 0x400000>;
|
|
};
|
|
partition@4 {
|
|
label = "swupdate (spi)";
|
|
reg = <0x50000 0x800000>;
|
|
};
|
|
};
|
|
};
|