Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-14 08:57:58 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/board/atmel/at91sam9m10g45ek/at91sam9m10g45ek.c
Scott Wood b616d9b0a7 nand: Embed mtd_info in struct nand_chip 
nand_info[] is now an array of pointers, with the actual mtd_info
instance embedded in struct nand_chip.

This is in preparation for syncing the NAND code with Linux 4.6,
which makes the same change to struct nand_chip.  It's in a separate
commit due to the large amount of changes required to accommodate the
change to nand_info[].

Signed-off-by: Scott Wood <oss@buserror.net>
2016-06-03 20:27:48 -05:00

387 lines
9.5 KiB
C
Raw Blame History

/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/clk.h>
#include <asm/arch/at91sam9g45_matrix.h>
#include <asm/arch/at91sam9_smc.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <lcd.h>
#include <linux/mtd/nand.h>
#include <atmel_lcdc.h>
#include <atmel_mci.h>
#if defined(CONFIG_RESET_PHY_R) && defined(CONFIG_MACB)
#include <net.h>
#endif
#include <netdev.h>
DECLARE_GLOBAL_DATA_PTR;
/* ------------------------------------------------------------------------- */
/*
* Miscelaneous platform dependent initialisations
*/
#ifdef CONFIG_CMD_NAND
void at91sam9m10g45ek_nand_hw_init(void)
{
struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
unsigned long csa;
/* Enable CS3 */
csa = readl(&matrix->ebicsa);
csa |= AT91_MATRIX_EBI_CS3A_SMC_SMARTMEDIA;
writel(csa, &matrix->ebicsa);
/* Configure SMC CS3 for NAND/SmartMedia */
writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
&smc->cs[3].setup);
writel(AT91_SMC_PULSE_NWE(4) | AT91_SMC_PULSE_NCS_WR(3) |
AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(2),
&smc->cs[3].pulse);
writel(AT91_SMC_CYCLE_NWE(7) | AT91_SMC_CYCLE_NRD(4),
&smc->cs[3].cycle);
writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
AT91_SMC_MODE_EXNW_DISABLE |
#ifdef CONFIG_SYS_NAND_DBW_16
AT91_SMC_MODE_DBW_16 |
#else /* CONFIG_SYS_NAND_DBW_8 */
AT91_SMC_MODE_DBW_8 |
#endif
AT91_SMC_MODE_TDF_CYCLE(3),
&smc->cs[3].mode);
at91_periph_clk_enable(ATMEL_ID_PIOC);
/* Configure RDY/BSY */
at91_set_gpio_input(CONFIG_SYS_NAND_READY_PIN, 1);
/* Enable NandFlash */
at91_set_gpio_output(CONFIG_SYS_NAND_ENABLE_PIN, 1);
}
#endif
#if defined(CONFIG_SPL_BUILD)
#include <spl.h>
#include <nand.h>
void at91_spl_board_init(void)
{
/*
* On the at91sam9m10g45ek board, the chip wm9711 stays in the
* test mode, so it needs do some action to exit test mode.
*/
at91_periph_clk_enable(ATMEL_ID_PIODE);
at91_set_gpio_output(AT91_PIN_PD7, 0);
at91_set_gpio_output(AT91_PIN_PD8, 0);
at91_set_pio_pullup(AT91_PIO_PORTD, 7, 1);
at91_set_pio_pullup(AT91_PIO_PORTD, 8, 1);
#ifdef CONFIG_SYS_USE_MMC
at91_mci_hw_init();
#elif CONFIG_SYS_USE_NANDFLASH
at91sam9m10g45ek_nand_hw_init();
#endif
}
#include <asm/arch/atmel_mpddrc.h>
static void ddr2_conf(struct atmel_mpddrc_config *ddr2)
{
ddr2->md = (ATMEL_MPDDRC_MD_DBW_16_BITS | ATMEL_MPDDRC_MD_DDR2_SDRAM);
ddr2->cr = (ATMEL_MPDDRC_CR_NC_COL_10 |
ATMEL_MPDDRC_CR_NR_ROW_14 |
ATMEL_MPDDRC_CR_DQMS_SHARED |
ATMEL_MPDDRC_CR_CAS_DDR_CAS3);
ddr2->rtr = 0x24b;
ddr2->tpr0 = (6 << ATMEL_MPDDRC_TPR0_TRAS_OFFSET |/* 6*7.5 = 45 ns */
2 << ATMEL_MPDDRC_TPR0_TRCD_OFFSET |/* 2*7.5 = 15 ns */
2 << ATMEL_MPDDRC_TPR0_TWR_OFFSET | /* 2*7.5 = 15 ns */
8 << ATMEL_MPDDRC_TPR0_TRC_OFFSET | /* 8*7.5 = 60 ns */
2 << ATMEL_MPDDRC_TPR0_TRP_OFFSET | /* 2*7.5 = 15 ns */
1 << ATMEL_MPDDRC_TPR0_TRRD_OFFSET | /* 1*7.5= 7.5 ns*/
1 << ATMEL_MPDDRC_TPR0_TWTR_OFFSET | /* 1 clk cycle */
2 << ATMEL_MPDDRC_TPR0_TMRD_OFFSET); /* 2 clk cycles */
ddr2->tpr1 = (2 << ATMEL_MPDDRC_TPR1_TXP_OFFSET | /* 2*7.5 = 15 ns */
200 << ATMEL_MPDDRC_TPR1_TXSRD_OFFSET |
16 << ATMEL_MPDDRC_TPR1_TXSNR_OFFSET |
14 << ATMEL_MPDDRC_TPR1_TRFC_OFFSET);
ddr2->tpr2 = (1 << ATMEL_MPDDRC_TPR2_TRTP_OFFSET |
0 << ATMEL_MPDDRC_TPR2_TRPA_OFFSET |
7 << ATMEL_MPDDRC_TPR2_TXARDS_OFFSET |
2 << ATMEL_MPDDRC_TPR2_TXARD_OFFSET);
}
void mem_init(void)
{
struct atmel_mpddrc_config ddr2;
ddr2_conf(&ddr2);
at91_system_clk_enable(AT91_PMC_DDR);
/* DDRAM2 Controller initialize */
ddr2_init(ATMEL_BASE_DDRSDRC0, ATMEL_BASE_CS6, &ddr2);
}
#endif
#ifdef CONFIG_CMD_USB
static void at91sam9m10g45ek_usb_hw_init(void)
{
at91_periph_clk_enable(ATMEL_ID_PIODE);
at91_set_gpio_output(AT91_PIN_PD1, 0);
at91_set_gpio_output(AT91_PIN_PD3, 0);
}
#endif
#ifdef CONFIG_MACB
static void at91sam9m10g45ek_macb_hw_init(void)
{
struct at91_port *pioa = (struct at91_port *)ATMEL_BASE_PIOA;
at91_periph_clk_enable(ATMEL_ID_EMAC);
/*
* Disable pull-up on:
* RXDV (PA15) => PHY normal mode (not Test mode)
* ERX0 (PA12) => PHY ADDR0
* ERX1 (PA13) => PHY ADDR1 => PHYADDR = 0x0
*
* PHY has internal pull-down
*/
writel(pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA12) |
pin_to_mask(AT91_PIN_PA13),
&pioa->pudr);
at91_phy_reset();
/* Re-enable pull-up */
writel(pin_to_mask(AT91_PIN_PA15) |
pin_to_mask(AT91_PIN_PA12) |
pin_to_mask(AT91_PIN_PA13),
&pioa->puer);
/* And the pins. */
at91_macb_hw_init();
}
#endif
#ifdef CONFIG_LCD
vidinfo_t panel_info = {
.vl_col = 480,
.vl_row = 272,
.vl_clk = 9000000,
.vl_sync = ATMEL_LCDC_INVLINE_NORMAL |
ATMEL_LCDC_INVFRAME_NORMAL,
.vl_bpix = 3,
.vl_tft = 1,
.vl_hsync_len = 45,
.vl_left_margin = 1,
.vl_right_margin = 1,
.vl_vsync_len = 1,
.vl_upper_margin = 40,
.vl_lower_margin = 1,
.mmio = ATMEL_BASE_LCDC,
};
void lcd_enable(void)
{
at91_set_A_periph(AT91_PIN_PE6, 1); /* power up */
}
void lcd_disable(void)
{
at91_set_A_periph(AT91_PIN_PE6, 0); /* power down */
}
static void at91sam9m10g45ek_lcd_hw_init(void)
{
at91_set_A_periph(AT91_PIN_PE0, 0); /* LCDDPWR */
at91_set_A_periph(AT91_PIN_PE2, 0); /* LCDCC */
at91_set_A_periph(AT91_PIN_PE3, 0); /* LCDVSYNC */
at91_set_A_periph(AT91_PIN_PE4, 0); /* LCDHSYNC */
at91_set_A_periph(AT91_PIN_PE5, 0); /* LCDDOTCK */
at91_set_A_periph(AT91_PIN_PE7, 0); /* LCDD0 */
at91_set_A_periph(AT91_PIN_PE8, 0); /* LCDD1 */
at91_set_A_periph(AT91_PIN_PE9, 0); /* LCDD2 */
at91_set_A_periph(AT91_PIN_PE10, 0); /* LCDD3 */
at91_set_A_periph(AT91_PIN_PE11, 0); /* LCDD4 */
at91_set_A_periph(AT91_PIN_PE12, 0); /* LCDD5 */
at91_set_A_periph(AT91_PIN_PE13, 0); /* LCDD6 */
at91_set_A_periph(AT91_PIN_PE14, 0); /* LCDD7 */
at91_set_A_periph(AT91_PIN_PE15, 0); /* LCDD8 */
at91_set_A_periph(AT91_PIN_PE16, 0); /* LCDD9 */
at91_set_A_periph(AT91_PIN_PE17, 0); /* LCDD10 */
at91_set_A_periph(AT91_PIN_PE18, 0); /* LCDD11 */
at91_set_A_periph(AT91_PIN_PE19, 0); /* LCDD12 */
at91_set_B_periph(AT91_PIN_PE20, 0); /* LCDD13 */
at91_set_A_periph(AT91_PIN_PE21, 0); /* LCDD14 */
at91_set_A_periph(AT91_PIN_PE22, 0); /* LCDD15 */
at91_set_A_periph(AT91_PIN_PE23, 0); /* LCDD16 */
at91_set_A_periph(AT91_PIN_PE24, 0); /* LCDD17 */
at91_set_A_periph(AT91_PIN_PE25, 0); /* LCDD18 */
at91_set_A_periph(AT91_PIN_PE26, 0); /* LCDD19 */
at91_set_A_periph(AT91_PIN_PE27, 0); /* LCDD20 */
at91_set_B_periph(AT91_PIN_PE28, 0); /* LCDD21 */
at91_set_A_periph(AT91_PIN_PE29, 0); /* LCDD22 */
at91_set_A_periph(AT91_PIN_PE30, 0); /* LCDD23 */
at91_periph_clk_enable(ATMEL_ID_LCDC);
gd->fb_base = CONFIG_AT91SAM9G45_LCD_BASE;
}
#ifdef CONFIG_LCD_INFO
#include <nand.h>
#include <version.h>
void lcd_show_board_info(void)
{
ulong dram_size, nand_size;
int i;
char temp[32];
lcd_printf ("%s\n", U_BOOT_VERSION);
lcd_printf ("(C) 2008 ATMEL Corp\n");
lcd_printf ("at91support@atmel.com\n");
lcd_printf ("%s CPU at %s MHz\n",
ATMEL_CPU_NAME,
strmhz(temp, get_cpu_clk_rate()));
dram_size = 0;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++)
dram_size += gd->bd->bi_dram[i].size;
nand_size = 0;
for (i = 0; i < CONFIG_SYS_MAX_NAND_DEVICE; i++)
nand_size += nand_info[i]->size;
lcd_printf (" %ld MB SDRAM, %ld MB NAND\n",
dram_size >> 20,
nand_size >> 20 );
}
#endif /* CONFIG_LCD_INFO */
#endif
#ifdef CONFIG_GENERIC_ATMEL_MCI
int board_mmc_init(bd_t *bis)
{
at91_mci_hw_init();
return atmel_mci_init((void *)ATMEL_BASE_MCI0);
}
#endif
int board_early_init_f(void)
{
at91_seriald_hw_init();
return 0;
}
int board_init(void)
{
/* arch number of AT91SAM9M10G45EK-Board */
#ifdef CONFIG_AT91SAM9M10G45EK
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9M10G45EK;
#elif defined CONFIG_AT91SAM9G45EKES
gd->bd->bi_arch_number = MACH_TYPE_AT91SAM9G45EKES;
#endif
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#ifdef CONFIG_CMD_NAND
at91sam9m10g45ek_nand_hw_init();
#endif
#ifdef CONFIG_CMD_USB
at91sam9m10g45ek_usb_hw_init();
#endif
#ifdef CONFIG_HAS_DATAFLASH
at91_spi0_hw_init(1 << 0);
#endif
#ifdef CONFIG_ATMEL_SPI
at91_spi0_hw_init(1 << 4);
#endif
#ifdef CONFIG_MACB
at91sam9m10g45ek_macb_hw_init();
#endif
#ifdef CONFIG_LCD
at91sam9m10g45ek_lcd_hw_init();
#endif
return 0;
}
int dram_init(void)
{
gd->ram_size = get_ram_size((void *) CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
#ifdef CONFIG_RESET_PHY_R
void reset_phy(void)
{
}
#endif
int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_MACB
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC, 0x00);
#endif
return rc;
}
/* SPI chip select control */
#ifdef CONFIG_ATMEL_SPI
#include <spi.h>
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
return bus == 0 && cs < 2;
}
void spi_cs_activate(struct spi_slave *slave)
{
switch(slave->cs) {
case 1:
at91_set_gpio_output(AT91_PIN_PB18, 0);
break;
case 0:
default:
at91_set_gpio_output(AT91_PIN_PB3, 0);
break;
}
}
void spi_cs_deactivate(struct spi_slave *slave)
{
switch(slave->cs) {
case 1:
at91_set_gpio_output(AT91_PIN_PB18, 1);
break;
case 0:
default:
at91_set_gpio_output(AT91_PIN_PB3, 1);
break;
}
}
#endif /* CONFIG_ATMEL_SPI */
Reference in a new issue View git blame Copy permalink