mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-29 22:43:10 +00:00
08574ed339
This converts the following to Kconfig: CONFIG_SYS_MONITOR_LEN To do this, we set a default of 0 for everyone because there are a number of cases where we define CONFIG_SYS_MONITOR_LEN but the only impact is that we set TOTAL_MALLOC_LEN to be CONFIG_SYS_MALLOC_LEN + CONFIG_ENV_SIZE, so we must continue to allow all boards to set this value. Update the SPL code to use 200 KB as the default raw U-Boot size directly, if we don't have a real CONFIG_SYS_MONITOR_LEN value. Signed-off-by: Tom Rini <trini@konsulko.com> Reviewed-by: Simon Glass <sjg@chromium.org>
134 lines
3.3 KiB
C
134 lines
3.3 KiB
C
/* SPDX-License-Identifier: GPL-2.0+ */
|
|
/*
|
|
* Copyright (C) 2010 Heiko Schocher <hs@denx.de>
|
|
*
|
|
* based on:
|
|
* Copyright (C) 2009 Ilya Yanok <yanok@emcraft.com>
|
|
*/
|
|
|
|
#ifndef __IMX27LITE_COMMON_CONFIG_H
|
|
#define __IMX27LITE_COMMON_CONFIG_H
|
|
|
|
/*
|
|
* SoC Configuration
|
|
*/
|
|
#define CONFIG_MX27
|
|
#define CONFIG_MX27_CLK32 32768 /* OSC32K frequency */
|
|
|
|
/*
|
|
* Lowlevel configuration
|
|
*/
|
|
#define SDRAM_ESDCFG_REGISTER_VAL(cas) \
|
|
(ESDCFG_TRC(10) | \
|
|
ESDCFG_TRCD(3) | \
|
|
ESDCFG_TCAS(cas) | \
|
|
ESDCFG_TRRD(1) | \
|
|
ESDCFG_TRAS(5) | \
|
|
ESDCFG_TWR | \
|
|
ESDCFG_TMRD(2) | \
|
|
ESDCFG_TRP(2) | \
|
|
ESDCFG_TXP(3))
|
|
|
|
#define SDRAM_ESDCTL_REGISTER_VAL \
|
|
(ESDCTL_PRCT(0) | \
|
|
ESDCTL_BL | \
|
|
ESDCTL_PWDT(0) | \
|
|
ESDCTL_SREFR(3) | \
|
|
ESDCTL_DSIZ_32 | \
|
|
ESDCTL_COL10 | \
|
|
ESDCTL_ROW13 | \
|
|
ESDCTL_SDE)
|
|
|
|
#define SDRAM_ALL_VAL 0xf00
|
|
|
|
#define SDRAM_MODE_REGISTER_VAL 0x33 /* BL: 8, CAS: 3 */
|
|
#define SDRAM_EXT_MODE_REGISTER_VAL 0x1000000
|
|
|
|
#define MPCTL0_VAL 0x1ef15d5
|
|
|
|
#define SPCTL0_VAL 0x043a1c09
|
|
|
|
#define CSCR_VAL 0x33f08107
|
|
|
|
#define PCDR0_VAL 0x120470c3
|
|
#define PCDR1_VAL 0x03030303
|
|
#define PCCR0_VAL 0xffffffff
|
|
#define PCCR1_VAL 0xfffffffc
|
|
|
|
#define AIPI1_PSR0_VAL 0x20040304
|
|
#define AIPI1_PSR1_VAL 0xdffbfcfb
|
|
#define AIPI2_PSR0_VAL 0x07ffc200
|
|
#define AIPI2_PSR1_VAL 0xffffffff
|
|
|
|
/*
|
|
* Memory Info
|
|
*/
|
|
/* memtest start address */
|
|
#define PHYS_SDRAM_1 0xA0000000 /* DDR Start */
|
|
#define PHYS_SDRAM_1_SIZE 0x08000000 /* DDR size 128MB */
|
|
|
|
/*
|
|
* Serial Driver info
|
|
*/
|
|
#define CONFIG_MXC_UART_BASE UART_BASE_ADDR(1)
|
|
|
|
/*
|
|
* Flash & Environment
|
|
*/
|
|
/* Use buffered writes (~10x faster) */
|
|
/* Use hardware sector protection */
|
|
/* CS2 Base address */
|
|
#define PHYS_FLASH_1 0xc0000000
|
|
/* Flash Base for U-Boot */
|
|
#define CONFIG_SYS_FLASH_BASE PHYS_FLASH_1
|
|
/* Address and size of Redundant Environment Sector */
|
|
|
|
/*
|
|
* Ethernet
|
|
*/
|
|
#define CONFIG_FEC_MXC_PHYADDR 0x1f
|
|
|
|
/*
|
|
* MTD
|
|
*/
|
|
|
|
/*
|
|
* NAND
|
|
*/
|
|
#define CONFIG_MXC_NAND_REGS_BASE 0xd8000000
|
|
#define CONFIG_SYS_NAND_BASE 0xd8000000
|
|
#define CONFIG_MXC_NAND_HWECC
|
|
|
|
/*
|
|
* U-Boot general configuration
|
|
*/
|
|
#define CONFIG_EXTRA_ENV_SETTINGS \
|
|
"netdev=eth0\0" \
|
|
"nfsargs=setenv bootargs root=/dev/nfs rw " \
|
|
"nfsroot=${serverip}:${rootpath}\0" \
|
|
"ramargs=setenv bootargs root=/dev/ram rw\0" \
|
|
"addip=setenv bootargs ${bootargs} " \
|
|
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
|
|
":${hostname}:${netdev}:off panic=1\0" \
|
|
"addtty=setenv bootargs ${bootargs}" \
|
|
" console=ttymxc0,${baudrate}\0" \
|
|
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
|
|
"addmisc=setenv bootargs ${bootargs}\0" \
|
|
"u-boot=" CONFIG_HOSTNAME "/u-boot.bin\0" \
|
|
"kernel_addr_r=a0800000\0" \
|
|
"bootfile=" CONFIG_HOSTNAME "/uImage\0" \
|
|
"rootpath=/opt/eldk-4.2-arm/arm\0" \
|
|
"net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
|
|
"run nfsargs addip addtty addmtd addmisc;" \
|
|
"bootm\0" \
|
|
"bootcmd=run net_nfs\0" \
|
|
"load=tftp ${loadaddr} ${u-boot}\0" \
|
|
"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
|
|
" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
|
|
" +${filesize};cp.b ${fileaddr} " \
|
|
__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
|
|
"upd=run load update\0" \
|
|
|
|
/* additions for new relocation code, must be added to all boards */
|
|
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
|
|
#endif /* __IMX27LITE_COMMON_CONFIG_H */
|