mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-12 16:07:30 +00:00
aba8004818
T1024QDS is a high-performance computing evaluation, development and test platform for T1024 QorIQ Power Architecture processor. T1024QDS board Overview ----------------------- - T1024 SoC integrating two 64-bit e5500 cores up to 1.4GHz - CoreNet fabric supporting coherent and noncoherent transactions with prioritization and bandwidth allocation - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving support - Accelerator: DPAA components consist of FMan, BMan, QMan, DCE and SEC - Ethernet interfaces: - Two 10M/100M/1G RGMII ports on-board - Three 1G/2.5Gbps SGMII ports - Four 1Gbps QSGMII ports - one 10Gbps XFI or 10Base-KR interface - SerDes: 4 lanes up to 10.3125GHz Supporting SGMII/QSGMII, XFI, PCIe, SATA and Aurora - PCIe: Three PCI Express controllers with five PCIe slots. - IFC: 128MB NOR Flash, 2GB NAND Flash, PromJet debug port and Qixis FPGA - Video: DIU supports video up to 1280x1024x32 bpp. - Chrontel CH7201 for HDMI connection. - TI DS90C387R for direct LCD connection. - Raw (not encoded) video connector for testing or other encoders. - QUICC Engine block - 32-bit RISC controller for flexible support of the communications peripherals - Serial DMA channel for receive and transmit on all serial channels - Two universal communication controllers, supporting TDM, HDLC, and UART - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) - eSPI: Three SPI flash devices. - SATA: one SATA 2.O. - USB: Two USB2.0 ports with internal PHY (one Type-A + one micro Type mini-AB) - eSDHC: Support SD, SDHC, SDXC and MMC/eMMC. - I2C: Four I2C controllers. - UART: Two UART on board. Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com> [York Sun: Fix ft_board_setup() type, fix MAINTAINERS for SECURE_BOOT Fix Kconfig by adding SUPPORT_SPL] Reviewed-by: York Sun <yorksun@freescale.com>
117 lines
4 KiB
C
117 lines
4 KiB
C
/*
|
|
* Copyright 2014 Freescale Semiconductor, Inc.
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <common.h>
|
|
#include <asm/mmu.h>
|
|
|
|
struct fsl_e_tlb_entry tlb_table[] = {
|
|
/* TLB 0 - for temp stack in cache */
|
|
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR,
|
|
CONFIG_SYS_INIT_RAM_ADDR_PHYS,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
0, 0, BOOKE_PAGESZ_4K, 0),
|
|
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 4 * 1024,
|
|
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 4 * 1024,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
0, 0, BOOKE_PAGESZ_4K, 0),
|
|
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 8 * 1024,
|
|
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 8 * 1024,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
0, 0, BOOKE_PAGESZ_4K, 0),
|
|
SET_TLB_ENTRY(0, CONFIG_SYS_INIT_RAM_ADDR + 12 * 1024,
|
|
CONFIG_SYS_INIT_RAM_ADDR_PHYS + 12 * 1024,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
0, 0, BOOKE_PAGESZ_4K, 0),
|
|
|
|
/* TLB 1 */
|
|
/* *I*** - Covers boot page */
|
|
#if defined(CONFIG_SYS_RAMBOOT) && defined(CONFIG_SYS_INIT_L3_ADDR)
|
|
/*
|
|
* *I*G - L3SRAM. When L3 is used as 256K SRAM, the address of the
|
|
* SRAM is at 0xfffc0000, it covered the 0xfffff000.
|
|
*/
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_INIT_L3_ADDR, CONFIG_SYS_INIT_L3_ADDR,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, 0, BOOKE_PAGESZ_256K, 1),
|
|
#else
|
|
SET_TLB_ENTRY(1, 0xfffff000, 0xfffff000,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, 0, BOOKE_PAGESZ_4K, 1),
|
|
#endif
|
|
|
|
/* *I*G* - CCSRBAR */
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_CCSRBAR, CONFIG_SYS_CCSRBAR_PHYS,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, 1, BOOKE_PAGESZ_16M, 1),
|
|
|
|
/* *I*G* - Flash, localbus */
|
|
/* This will be changed to *I*G* after relocation to RAM. */
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_FLASH_BASE, CONFIG_SYS_FLASH_BASE_PHYS,
|
|
MAS3_SX|MAS3_SR, MAS2_W|MAS2_G,
|
|
0, 2, BOOKE_PAGESZ_256M, 1),
|
|
|
|
#ifndef CONFIG_SPL_BUILD
|
|
/* *I*G* - PCI */
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_MEM_VIRT, CONFIG_SYS_PCIE1_MEM_PHYS,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, 3, BOOKE_PAGESZ_1G, 1),
|
|
|
|
/* *I*G* - PCI I/O */
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_PCIE1_IO_VIRT, CONFIG_SYS_PCIE1_IO_PHYS,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, 4, BOOKE_PAGESZ_256K, 1),
|
|
|
|
/* Bman/Qman */
|
|
#ifdef CONFIG_SYS_BMAN_MEM_PHYS
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE, CONFIG_SYS_BMAN_MEM_PHYS,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
0, 5, BOOKE_PAGESZ_16M, 1),
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_BMAN_MEM_BASE + 0x01000000,
|
|
CONFIG_SYS_BMAN_MEM_PHYS + 0x01000000,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, 6, BOOKE_PAGESZ_16M, 1),
|
|
#endif
|
|
#ifdef CONFIG_SYS_QMAN_MEM_PHYS
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE, CONFIG_SYS_QMAN_MEM_PHYS,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
0, 7, BOOKE_PAGESZ_16M, 1),
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_QMAN_MEM_BASE + 0x01000000,
|
|
CONFIG_SYS_QMAN_MEM_PHYS + 0x01000000,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, 8, BOOKE_PAGESZ_16M, 1),
|
|
#endif
|
|
#endif
|
|
#ifdef CONFIG_SYS_DCSRBAR_PHYS
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_DCSRBAR, CONFIG_SYS_DCSRBAR_PHYS,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, 9, BOOKE_PAGESZ_4M, 1),
|
|
#endif
|
|
#ifdef CONFIG_SYS_NAND_BASE
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, 10, BOOKE_PAGESZ_64K, 1),
|
|
#endif
|
|
#ifdef QIXIS_BASE
|
|
SET_TLB_ENTRY(1, QIXIS_BASE, QIXIS_BASE_PHYS,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
|
|
0, 11, BOOKE_PAGESZ_4K, 1),
|
|
#endif
|
|
|
|
#if defined(CONFIG_RAMBOOT_PBL) && !defined(CONFIG_SPL_BUILD)
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE, CONFIG_SYS_DDR_SDRAM_BASE,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
0, 12, BOOKE_PAGESZ_1G, 1),
|
|
SET_TLB_ENTRY(1, CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
|
|
CONFIG_SYS_DDR_SDRAM_BASE + 0x40000000,
|
|
MAS3_SX|MAS3_SW|MAS3_SR, 0,
|
|
0, 13, BOOKE_PAGESZ_1G, 1)
|
|
#endif
|
|
/* entry 14 and 15 has been used hard coded, they will be disabled
|
|
* in cpu_init_f, so if needed more, will use entry 16 later.
|
|
*/
|
|
};
|
|
|
|
int num_tlb_entries = ARRAY_SIZE(tlb_table);
|