u-boot/board/freescale/ls1043ardb/cpld.c
Gong Qianyu c7ca8b07fc armv8/ls1043ardb: Add sd boot support
Signed-off-by: Gong Qianyu <Qianyu.Gong@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2015-10-29 10:34:02 -07:00

152 lines
3.2 KiB
C

/*
* Copyright 2015 Freescale Semiconductor
*
* SPDX-License-Identifier: GPL-2.0+
*
* Freescale LS1043ARDB board-specific CPLD controlling supports.
*/
#include <common.h>
#include <command.h>
#include <asm/io.h>
#include "cpld.h"
u8 cpld_read(unsigned int reg)
{
void *p = (void *)CONFIG_SYS_CPLD_BASE;
return in_8(p + reg);
}
void cpld_write(unsigned int reg, u8 value)
{
void *p = (void *)CONFIG_SYS_CPLD_BASE;
out_8(p + reg, value);
}
/* Set the boot bank to the alternate bank */
void cpld_set_altbank(void)
{
u8 reg4 = CPLD_READ(soft_mux_on);
u8 reg7 = CPLD_READ(vbank);
CPLD_WRITE(soft_mux_on, reg4 | CPLD_SW_MUX_BANK_SEL);
reg7 = (reg7 & ~CPLD_BANK_SEL_MASK) | CPLD_BANK_SEL_ALTBANK;
CPLD_WRITE(vbank, reg7);
CPLD_WRITE(system_rst, 1);
}
/* Set the boot bank to the default bank */
void cpld_set_defbank(void)
{
CPLD_WRITE(global_rst, 1);
}
void cpld_set_nand(void)
{
u16 reg = CPLD_CFG_RCW_SRC_NAND;
u8 reg5 = (u8)(reg >> 1);
u8 reg6 = (u8)(reg & 1);
cpld_rev_bit(&reg5);
CPLD_WRITE(soft_mux_on, 1);
CPLD_WRITE(cfg_rcw_src1, reg5);
CPLD_WRITE(cfg_rcw_src2, reg6);
CPLD_WRITE(system_rst, 1);
}
void cpld_set_sd(void)
{
u16 reg = CPLD_CFG_RCW_SRC_SD;
u8 reg5 = (u8)(reg >> 1);
u8 reg6 = (u8)(reg & 1);
cpld_rev_bit(&reg5);
CPLD_WRITE(soft_mux_on, 1);
CPLD_WRITE(cfg_rcw_src1, reg5);
CPLD_WRITE(cfg_rcw_src2, reg6);
CPLD_WRITE(system_rst, 1);
}
#ifdef DEBUG
static void cpld_dump_regs(void)
{
printf("cpld_ver = %x\n", CPLD_READ(cpld_ver));
printf("cpld_ver_sub = %x\n", CPLD_READ(cpld_ver_sub));
printf("pcba_ver = %x\n", CPLD_READ(pcba_ver));
printf("soft_mux_on = %x\n", CPLD_READ(soft_mux_on));
printf("cfg_rcw_src1 = %x\n", CPLD_READ(cfg_rcw_src1));
printf("cfg_rcw_src2 = %x\n", CPLD_READ(cfg_rcw_src2));
printf("vbank = %x\n", CPLD_READ(vbank));
printf("sysclk_sel = %x\n", CPLD_READ(sysclk_sel));
printf("uart_sel = %x\n", CPLD_READ(uart_sel));
printf("sd1refclk_sel = %x\n", CPLD_READ(sd1refclk_sel));
printf("tdmclk_mux_sel = %x\n", CPLD_READ(tdmclk_mux_sel));
printf("sdhc_spics_sel = %x\n", CPLD_READ(sdhc_spics_sel));
printf("status_led = %x\n", CPLD_READ(status_led));
putc('\n');
}
#endif
void cpld_rev_bit(unsigned char *value)
{
u8 rev_val, val;
int i;
val = *value;
rev_val = val & 1;
for (i = 1; i <= 7; i++) {
val >>= 1;
rev_val <<= 1;
rev_val |= val & 1;
}
*value = rev_val;
}
int do_cpld(cmd_tbl_t *cmdtp, int flag, int argc, char * const argv[])
{
int rc = 0;
if (argc <= 1)
return cmd_usage(cmdtp);
if (strcmp(argv[1], "reset") == 0) {
if (strcmp(argv[2], "altbank") == 0)
cpld_set_altbank();
else if (strcmp(argv[2], "nand") == 0)
cpld_set_nand();
else if (strcmp(argv[2], "sd") == 0)
cpld_set_sd();
else
cpld_set_defbank();
#ifdef DEBUG
} else if (strcmp(argv[1], "dump") == 0) {
cpld_dump_regs();
#endif
} else {
rc = cmd_usage(cmdtp);
}
return rc;
}
U_BOOT_CMD(
cpld, CONFIG_SYS_MAXARGS, 1, do_cpld,
"Reset the board or alternate bank",
"reset: reset to default bank\n"
"cpld reset altbank: reset to alternate bank\n"
"cpld reset nand: reset to boot from NAND flash\n"
"cpld reset sd: reset to boot from SD card\n"
#ifdef DEBUG
"cpld dump - display the CPLD registers\n"
#endif
);