Mirrors/u-boot
2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-11-08 14:14:32 +00:00
Code Issues Projects Releases Packages Wiki Activity
u-boot/board/l+g/vinco/vinco.c
Lukasz Majewski 56c4046038 spi: Convert CONFIG_DM_SPI* to CONFIG_$(SPL_TPL_)DM_SPI* 
This change allows more fine tuning of driver model based SPI support in
SPL and TPL. It is now possible to explicitly enable/disable the DM_SPI
support in SPL and TPL via Kconfig option.

Before this change it was necessary to use:
    /* SPI Flash Configs */
    #if defined(CONFIG_SPL_BUILD)
    #undef CONFIG_DM_SPI
    #undef CONFIG_DM_SPI_FLASH
    #undef CONFIG_SPI_FLASH_MTD
    #endif

in the ./include/configs/<board>.h, which is error prone and shall be
avoided when we strive to switch to Kconfig.

The goal of this patch:

Provide distinction for DM_SPI support in both U-Boot proper and SPL (TPL).
Valid use case is when U-Boot proper wants to use DM_SPI, but SPL must
still support non DM driver.

Another use case is the conversion of non DM/DTS SPI driver to support
DM/DTS. When such driver needs to work in both SPL and U-Boot proper, the
distinction is needed in Kconfig (also if SPL version of the driver
supports OF_PLATDATA).

In the end of the day one would have to support following use cases (in
single driver file - e.g. mxs_spi.c):

- U-Boot proper driver supporting DT/DTS
- U-Boot proper driver without DT/DTS support (deprecated)
- SPL driver without DT/DTS support
- SPL (and TPL) driver with DT/DTS (when the SoC has enough resources to
  run full blown DT/DTS)
- SPL driver with DT/DTS and SPL_OF_PLATDATA (when one have constrained
  environment with no fitImage and OF_LIBFDT support).

Some boards do require SPI support (with DM) in SPL (TPL) and some only
have DM_SPI{_FLASH} defined to allow compiling SPL.

This patch converts #ifdef CONFIG_DM_SPI* to #if CONFIG_IS_ENABLED(DM_SPI)
and provides corresponding defines in Kconfig.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Adam Ford <aford173@gmail.com> #da850-evm
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
[trini: Fixup a few platforms]
Signed-off-by: Tom Rini <trini@konsulko.com>
2020-06-29 13:34:43 -04:00

213 lines
5.5 KiB
C
Raw Blame History

// SPDX-License-Identifier: GPL-2.0+
/*
* Board file for the VInCo platform
* Based on the the SAMA5-EK board file
* Configuration settings for the VInCo platform.
* Copyright (C) 2014 Atmel
* Bo Shen <voice.shen@atmel.com>
* Copyright (C) 2015 Free Electrons
* Gregory CLEMENT <gregory.clement@free-electrons.com>
*/
#include <common.h>
#include <init.h>
#include <asm/io.h>
#include <asm/arch/at91_common.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/at91_rstc.h>
#include <asm/arch/atmel_mpddrc.h>
#include <asm/arch/atmel_usba_udc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/clk.h>
#include <asm/arch/sama5d3_smc.h>
#include <asm/arch/sama5d4.h>
#include <atmel_hlcdc.h>
#include <atmel_mci.h>
#include <lcd.h>
#include <mmc.h>
#include <net.h>
#include <netdev.h>
#include <nand.h>
#include <spi.h>
#include <version.h>
DECLARE_GLOBAL_DATA_PTR;
/* FIXME gpio code here need to handle through DM_GPIO */
#if !CONFIG_IS_ENABLED(DM_SPI)
int spi_cs_is_valid(unsigned int bus, unsigned int cs)
{
return bus == 0 && cs == 0;
}
void spi_cs_activate(struct spi_slave *slave)
{
at91_set_pio_output(AT91_PIO_PORTC, 3, 0);
}
void spi_cs_deactivate(struct spi_slave *slave)
{
at91_set_pio_output(AT91_PIO_PORTC, 3, 1);
}
static void vinco_spi0_hw_init(void)
{
at91_pio3_set_a_periph(AT91_PIO_PORTC, 0, 0); /* SPI0_MISO */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 1, 0); /* SPI0_MOSI */
at91_pio3_set_a_periph(AT91_PIO_PORTC, 2, 0); /* SPI0_SPCK */
at91_set_pio_output(AT91_PIO_PORTC, 3, 1); /* SPI0_CS0 */
/* Enable clock */
at91_periph_clk_enable(ATMEL_ID_SPI0);
}
#endif /* CONFIG_ATMEL_SPI */
#ifdef CONFIG_CMD_USB
static void vinco_usb_hw_init(void)
{
at91_set_pio_output(AT91_PIO_PORTE, 11, 0);
at91_set_pio_output(AT91_PIO_PORTE, 12, 0);
at91_set_pio_output(AT91_PIO_PORTE, 10, 0);
}
#endif
#ifdef CONFIG_GENERIC_ATMEL_MCI
void vinco_mci0_hw_init(void)
{
at91_pio3_set_b_periph(AT91_PIO_PORTC, 5, 1); /* MCI0 CDA */
at91_pio3_set_b_periph(AT91_PIO_PORTC, 6, 1); /* MCI0 DA0 */
at91_pio3_set_b_periph(AT91_PIO_PORTC, 7, 1); /* MCI0 DA1 */
at91_pio3_set_b_periph(AT91_PIO_PORTC, 8, 1); /* MCI0 DA2 */
at91_pio3_set_b_periph(AT91_PIO_PORTC, 9, 1); /* MCI0 DA3 */
at91_pio3_set_b_periph(AT91_PIO_PORTC, 10, 1); /* MCI0 DA4 */
at91_pio3_set_b_periph(AT91_PIO_PORTC, 11, 1); /* MCI0 DA5 */
at91_pio3_set_b_periph(AT91_PIO_PORTC, 12, 1); /* MCI0 DA6 */
at91_pio3_set_b_periph(AT91_PIO_PORTC, 13, 1); /* MCI0 DA7 */
at91_pio3_set_b_periph(AT91_PIO_PORTC, 4, 0); /* MCI0 CLK */
/*
* As the mci io internal pull down is too strong, so if the io needs
* external pull up, the pull up resistor will be very small, if so
* the power consumption will increase, so disable the interanl pull
* down to save the power.
*/
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 4, 0);
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 5, 0);
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 6, 0);
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 7, 0);
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 8, 0);
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 9, 0);
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 10, 0);
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 11, 0);
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 12, 0);
at91_pio3_set_pio_pulldown(AT91_PIO_PORTC, 13, 0);
/* Enable clock */
at91_periph_clk_enable(ATMEL_ID_MCI0);
}
int board_mmc_init(bd_t *bis)
{
/* Enable power for MCI0 interface */
at91_set_pio_output(AT91_PIO_PORTE, 7, 1);
return atmel_mci_init((void *)ATMEL_BASE_MCI0);
}
#endif /* CONFIG_GENERIC_ATMEL_MCI */
#ifdef CONFIG_MACB
void vinco_macb0_hw_init(void)
{
at91_pio3_set_a_periph(AT91_PIO_PORTB, 0, 0); /* ETXCK_EREFCK */
at91_pio3_set_a_periph(AT91_PIO_PORTB, 6, 0); /* ERXDV */
at91_pio3_set_a_periph(AT91_PIO_PORTB, 8, 0); /* ERX0 */
at91_pio3_set_a_periph(AT91_PIO_PORTB, 9, 0); /* ERX1 */
at91_pio3_set_a_periph(AT91_PIO_PORTB, 7, 0); /* ERXER */
at91_pio3_set_a_periph(AT91_PIO_PORTB, 2, 0); /* ETXEN */
at91_pio3_set_a_periph(AT91_PIO_PORTB, 12, 0); /* ETX0 */
at91_pio3_set_a_periph(AT91_PIO_PORTB, 13, 0); /* ETX1 */
at91_pio3_set_a_periph(AT91_PIO_PORTB, 17, 0); /* EMDIO */
at91_pio3_set_a_periph(AT91_PIO_PORTB, 16, 0); /* EMDC */
/* Enable clock */
at91_periph_clk_enable(ATMEL_ID_GMAC0);
/* Enable Phy*/
at91_set_pio_output(AT91_PIO_PORTE, 8, 1);
}
#endif
static void vinco_serial3_hw_init(void)
{
at91_pio3_set_b_periph(AT91_PIO_PORTE, 17, 1); /* TXD3 */
at91_pio3_set_b_periph(AT91_PIO_PORTE, 16, 0); /* RXD3 */
/* Enable clock */
at91_periph_clk_enable(ATMEL_ID_USART3);
}
int board_early_init_f(void)
{
at91_periph_clk_enable(ATMEL_ID_PIOA);
at91_periph_clk_enable(ATMEL_ID_PIOB);
at91_periph_clk_enable(ATMEL_ID_PIOC);
at91_periph_clk_enable(ATMEL_ID_PIOD);
at91_periph_clk_enable(ATMEL_ID_PIOE);
vinco_serial3_hw_init();
return 0;
}
int board_init(void)
{
/* adress of boot parameters */
gd->bd->bi_boot_params = CONFIG_SYS_SDRAM_BASE + 0x100;
#if !CONFIG_IS_ENABLED(DM_SPI)
vinco_spi0_hw_init();
#endif
#ifdef CONFIG_GENERIC_ATMEL_MCI
vinco_mci0_hw_init();
#endif
#ifdef CONFIG_MACB
vinco_macb0_hw_init();
#endif
#ifdef CONFIG_CMD_USB
vinco_usb_hw_init();
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
at91_udp_hw_init();
#endif
return 0;
}
int dram_init(void)
{
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
CONFIG_SYS_SDRAM_SIZE);
return 0;
}
int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_MACB
rc = macb_eth_initialize(0, (void *)ATMEL_BASE_GMAC0, 0x00);
#endif
#ifdef CONFIG_USB_GADGET_ATMEL_USBA
usba_udc_probe(&pdata);
#ifdef CONFIG_USB_ETH_RNDIS
usb_eth_initialize(bis);
#endif
#endif
return rc;
}
Reference in a new issue View git blame Copy permalink