mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-12-02 01:19:49 +00:00
938076efa9
Register LDOGCTL contains only bit 0 as a valid bit, so there is no need to do a read-modify-write operation. Simplify the code by writing directly to this register. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
293 lines
7.3 KiB
C
293 lines
7.3 KiB
C
/*
|
|
* Copyright (C) 2015 Technexion Ltd.
|
|
*
|
|
* Author: Richard Hu <richard.hu@technexion.com>
|
|
*
|
|
* SPDX-License-Identifier: GPL-2.0+
|
|
*/
|
|
|
|
#include <asm/arch/clock.h>
|
|
#include <asm/arch/iomux.h>
|
|
#include <asm/arch/imx-regs.h>
|
|
#include <asm/arch/crm_regs.h>
|
|
#include <asm/arch/mx6-pins.h>
|
|
#include <asm/arch/sys_proto.h>
|
|
#include <asm/gpio.h>
|
|
#include <asm/imx-common/iomux-v3.h>
|
|
#include <asm/imx-common/mxc_i2c.h>
|
|
#include <asm/io.h>
|
|
#include <common.h>
|
|
#include <miiphy.h>
|
|
#include <netdev.h>
|
|
#include <fsl_esdhc.h>
|
|
#include <i2c.h>
|
|
#include <linux/sizes.h>
|
|
#include <usb.h>
|
|
#include <power/pmic.h>
|
|
#include <power/pfuze3000_pmic.h>
|
|
#include "../../freescale/common/pfuze.h"
|
|
|
|
DECLARE_GLOBAL_DATA_PTR;
|
|
|
|
#define UART_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define USDHC_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_22K_UP | PAD_CTL_SPEED_LOW | \
|
|
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define I2C_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED | \
|
|
PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
|
|
PAD_CTL_ODE)
|
|
|
|
#define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE | \
|
|
PAD_CTL_PUS_47K_UP | PAD_CTL_SPEED_LOW | \
|
|
PAD_CTL_DSE_80ohm | PAD_CTL_SRE_FAST | PAD_CTL_HYS)
|
|
|
|
#define MDIO_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
|
|
PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST | PAD_CTL_ODE)
|
|
|
|
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | PAD_CTL_PUE | \
|
|
PAD_CTL_SPEED_HIGH | \
|
|
PAD_CTL_DSE_48ohm | PAD_CTL_SRE_FAST)
|
|
|
|
#define ENET_CLK_PAD_CTRL (PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
|
|
|
|
#define RMII_PHY_RESET IMX_GPIO_NR(1, 28)
|
|
|
|
#ifdef CONFIG_SYS_I2C_MXC
|
|
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
|
|
/* I2C2 for PMIC */
|
|
struct i2c_pads_info i2c_pad_info1 = {
|
|
.scl = {
|
|
.i2c_mode = MX6_PAD_GPIO1_IO02__I2C1_SCL | PC,
|
|
.gpio_mode = MX6_PAD_GPIO1_IO02__GPIO1_IO02 | PC,
|
|
.gp = IMX_GPIO_NR(1, 2),
|
|
},
|
|
.sda = {
|
|
.i2c_mode = MX6_PAD_GPIO1_IO03__I2C1_SDA | PC,
|
|
.gpio_mode = MX6_PAD_GPIO1_IO03__GPIO1_IO03 | PC,
|
|
.gp = IMX_GPIO_NR(1, 3),
|
|
},
|
|
};
|
|
#endif
|
|
|
|
static iomux_v3_cfg_t const fec_pads[] = {
|
|
MX6_PAD_ENET1_TX_EN__ENET2_MDC | MUX_PAD_CTRL(MDIO_PAD_CTRL),
|
|
MX6_PAD_ENET1_TX_DATA1__ENET2_MDIO | MUX_PAD_CTRL(MDIO_PAD_CTRL),
|
|
MX6_PAD_ENET2_TX_DATA0__ENET2_TDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET2_TX_DATA1__ENET2_TDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET2_TX_CLK__ENET2_REF_CLK2 | MUX_PAD_CTRL(ENET_CLK_PAD_CTRL),
|
|
MX6_PAD_ENET2_TX_EN__ENET2_TX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET2_RX_DATA0__ENET2_RDATA00 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET2_RX_DATA1__ENET2_RDATA01 | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET2_RX_EN__ENET2_RX_EN | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_ENET2_RX_ER__ENET2_RX_ER | MUX_PAD_CTRL(ENET_PAD_CTRL),
|
|
MX6_PAD_UART4_TX_DATA__GPIO1_IO28 | MUX_PAD_CTRL(NO_PAD_CTRL),
|
|
};
|
|
|
|
static void setup_iomux_fec(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
|
|
}
|
|
|
|
int board_eth_init(bd_t *bis)
|
|
{
|
|
setup_iomux_fec();
|
|
|
|
gpio_direction_output(RMII_PHY_RESET, 0);
|
|
/*
|
|
* According to KSZ8081MNX-RNB manual:
|
|
* For warm reset, the reset (RST#) pin should be asserted low for a
|
|
* minimum of 500μs. The strap-in pin values are read and updated
|
|
* at the de-assertion of reset.
|
|
*/
|
|
udelay(500);
|
|
|
|
gpio_direction_output(RMII_PHY_RESET, 1);
|
|
/*
|
|
* According to KSZ8081MNX-RNB manual:
|
|
* After the de-assertion of reset, wait a minimum of 100μs before
|
|
* starting programming on the MIIM (MDC/MDIO) interface.
|
|
*/
|
|
udelay(100);
|
|
|
|
return fecmxc_initialize(bis);
|
|
}
|
|
|
|
static int setup_fec(void)
|
|
{
|
|
struct iomuxc *const iomuxc_regs = (struct iomuxc *)IOMUXC_BASE_ADDR;
|
|
int ret;
|
|
|
|
clrsetbits_le32(&iomuxc_regs->gpr[1], IOMUX_GPR1_FEC2_MASK,
|
|
IOMUX_GPR1_FEC2_CLOCK_MUX1_SEL_MASK);
|
|
|
|
ret = enable_fec_anatop_clock(1, ENET_50MHZ);
|
|
if (ret)
|
|
return ret;
|
|
|
|
enable_enet_clk(1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_phy_config(struct phy_device *phydev)
|
|
{
|
|
phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x8190);
|
|
|
|
if (phydev->drv->config)
|
|
phydev->drv->config(phydev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int dram_init(void)
|
|
{
|
|
gd->ram_size = imx_ddr_size();
|
|
|
|
return 0;
|
|
}
|
|
|
|
static iomux_v3_cfg_t const uart6_pads[] = {
|
|
MX6_PAD_CSI_MCLK__UART6_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
MX6_PAD_CSI_PIXCLK__UART6_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
|
|
};
|
|
|
|
static iomux_v3_cfg_t const usdhc1_pads[] = {
|
|
MX6_PAD_SD1_CLK__USDHC1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD1_CMD__USDHC1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD1_DATA0__USDHC1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD1_DATA1__USDHC1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD1_DATA2__USDHC1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_SD1_DATA3__USDHC1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_NAND_READY_B__USDHC1_DATA4 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_NAND_CE0_B__USDHC1_DATA5 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_NAND_CE1_B__USDHC1_DATA6 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
MX6_PAD_NAND_CLE__USDHC1_DATA7 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
|
|
};
|
|
|
|
#define USB_OTHERREGS_OFFSET 0x800
|
|
#define UCTRL_PWR_POL (1 << 9)
|
|
|
|
static iomux_v3_cfg_t const usb_otg_pad[] = {
|
|
MX6_PAD_GPIO1_IO00__ANATOP_OTG1_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
|
|
};
|
|
|
|
static void setup_iomux_uart(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(uart6_pads, ARRAY_SIZE(uart6_pads));
|
|
}
|
|
|
|
static void setup_usb(void)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(usb_otg_pad, ARRAY_SIZE(usb_otg_pad));
|
|
}
|
|
|
|
static struct fsl_esdhc_cfg usdhc_cfg[1] = {
|
|
{USDHC1_BASE_ADDR},
|
|
};
|
|
|
|
int board_mmc_getcd(struct mmc *mmc)
|
|
{
|
|
return 1;
|
|
}
|
|
|
|
int board_mmc_init(bd_t *bis)
|
|
{
|
|
imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
|
|
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
|
|
return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
|
|
}
|
|
|
|
int board_early_init_f(void)
|
|
{
|
|
setup_iomux_uart();
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_POWER
|
|
#define I2C_PMIC 0
|
|
static struct pmic *pfuze;
|
|
int power_init_board(void)
|
|
{
|
|
int ret;
|
|
unsigned int reg, rev_id;
|
|
|
|
ret = power_pfuze3000_init(I2C_PMIC);
|
|
if (ret)
|
|
return ret;
|
|
|
|
pfuze = pmic_get("PFUZE3000");
|
|
ret = pmic_probe(pfuze);
|
|
if (ret)
|
|
return ret;
|
|
|
|
pmic_reg_read(pfuze, PFUZE3000_DEVICEID, ®);
|
|
pmic_reg_read(pfuze, PFUZE3000_REVID, &rev_id);
|
|
printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", reg, rev_id);
|
|
|
|
/* disable Low Power Mode during standby mode */
|
|
pmic_reg_write(pfuze, PFUZE3000_LDOGCTL, 0x1);
|
|
|
|
/* SW1B step ramp up time from 2us to 4us/25mV */
|
|
pmic_reg_write(pfuze, PFUZE3000_SW1BCONF, 0x40);
|
|
|
|
/* SW1B mode to APS/PFM */
|
|
pmic_reg_write(pfuze, PFUZE3000_SW1BMODE, 0xc);
|
|
|
|
/* SW1B standby voltage set to 0.975V */
|
|
pmic_reg_write(pfuze, PFUZE3000_SW1BSTBY, 0xb);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
int board_usb_phy_mode(int port)
|
|
{
|
|
if (port == 1)
|
|
return USB_INIT_HOST;
|
|
else
|
|
return USB_INIT_DEVICE;
|
|
}
|
|
|
|
int board_ehci_hcd_init(int port)
|
|
{
|
|
u32 *usbnc_usb_ctrl;
|
|
|
|
if (port > 1)
|
|
return -EINVAL;
|
|
|
|
usbnc_usb_ctrl = (u32 *)(USB_BASE_ADDR + USB_OTHERREGS_OFFSET +
|
|
port * 4);
|
|
|
|
/* Set Power polarity */
|
|
setbits_le32(usbnc_usb_ctrl, UCTRL_PWR_POL);
|
|
|
|
return 0;
|
|
}
|
|
|
|
int board_init(void)
|
|
{
|
|
/* Address of boot parameters */
|
|
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
|
|
|
|
#ifdef CONFIG_SYS_I2C_MXC
|
|
setup_i2c(0, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
|
|
#endif
|
|
|
|
setup_fec();
|
|
setup_usb();
|
|
|
|
return 0;
|
|
}
|
|
|
|
int checkboard(void)
|
|
{
|
|
puts("Board: PICO-IMX6UL-EMMC\n");
|
|
|
|
return 0;
|
|
}
|