u-boot/include/configs/cmpcpro.h
Christophe Leroy 4d0c8db74d board: cssi: Add CPU board CMPCPRO
CSSI has another CPU board, similar to the CMPC885 board
that get plugged on the two base boards MCR3000_2G and MIAE.

That CPU board is called CMPCPRO because it has a MPC8321E CPU,
also known as Power QUICC II PRO.

Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
2023-04-28 17:52:23 +02:00

99 lines
3 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2006-2023 CS GROUP France
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <linux/sizes.h>
/*
* System IO Config
*/
#define CFG_SYS_SICRL 0x00000000
#define CFG_SYS_DDR_SDRAM_BASE 0x00000000
#define CFG_SYS_DDRCDR 0x73000002 /* DDR II voltage is 1.8V */
/*
* Manually set up DDR parameters
*/
/* DDR 512 M */
#define CFG_SYS_DDR_CS0_CONFIG (CSCONFIG_EN | CSCONFIG_ODT_WR_CFG | CSCONFIG_BANK_BIT_3 | \
CSCONFIG_ROW_BIT_14 | CSCONFIG_COL_BIT_10)
/* 0x80840102 */
#define CFG_SYS_DDR_TIMING_0 ((0 << TIMING_CFG0_RWT_SHIFT) | \
(0 << TIMING_CFG0_WRT_SHIFT) | \
(0 << TIMING_CFG0_RRT_SHIFT) | \
(0 << TIMING_CFG0_WWT_SHIFT) | \
(2 << TIMING_CFG0_ACT_PD_EXIT_SHIFT) | \
(2 << TIMING_CFG0_PRE_PD_EXIT_SHIFT) | \
(8 << TIMING_CFG0_ODT_PD_EXIT_SHIFT) | \
(2 << TIMING_CFG0_MRS_CYC_SHIFT))
/* 0x00220802 */
#define CFG_SYS_DDR_TIMING_1 ((2 << TIMING_CFG1_PRETOACT_SHIFT) | \
(6 << TIMING_CFG1_ACTTOPRE_SHIFT) | \
(2 << TIMING_CFG1_ACTTORW_SHIFT) | \
(5 << TIMING_CFG1_CASLAT_SHIFT) | \
(27 << TIMING_CFG1_REFREC_SHIFT) | \
(2 << TIMING_CFG1_WRREC_SHIFT) | \
(2 << TIMING_CFG1_ACTTOACT_SHIFT) | \
(2 << TIMING_CFG1_WRTORD_SHIFT))
/* 0x3935D322 */
#define CFG_SYS_DDR_TIMING_2 ((0 << TIMING_CFG2_ADD_LAT_SHIFT) | \
(31 << TIMING_CFG2_CPO_SHIFT) | \
(2 << TIMING_CFG2_WR_LAT_DELAY_SHIFT) | \
(2 << TIMING_CFG2_RD_TO_PRE_SHIFT) | \
(2 << TIMING_CFG2_WR_DATA_DELAY_SHIFT) | \
(3 << TIMING_CFG2_CKE_PLS_SHIFT) | \
(7 << TIMING_CFG2_FOUR_ACT_SHIFT))
/* 0x0F9048CA */
#define CFG_SYS_DDR_TIMING_3 0x00000000
#define CFG_SYS_DDR_CLK_CNTL DDR_SDRAM_CLK_CNTL_CLK_ADJUST_05
/* 0x02000000 */
#define CFG_SYS_DDR_MODE ((0x4440 << SDRAM_MODE_ESD_SHIFT) | (0x0232 << SDRAM_MODE_SD_SHIFT))
/* 0x44400232 */
#define CFG_SYS_DDR_MODE2 0x8000c000
#define CFG_SYS_DDR_INTERVAL ((800 << SDRAM_INTERVAL_REFINT_SHIFT) | \
(100 << SDRAM_INTERVAL_BSTOPRE_SHIFT))
#define CFG_SYS_DDR_CS0_BNDS (CFG_SYS_DDR_SDRAM_BASE >> 8 | 0x0000001F)
#define CFG_SYS_DDR_SDRAM_CFG (SDRAM_CFG_SREN | SDRAM_CFG_SDRAM_TYPE_DDR2 | SDRAM_CFG_32_BE)
/* 0x43080000 */
#define CFG_SYS_DDR_SDRAM_CFG2 0x00401000
/*
* Initial RAM Base Address Setup
*/
#define CFG_SYS_INIT_RAM_ADDR (CONFIG_SYS_IMMR + 0x110000)
#define CFG_SYS_INIT_RAM_SIZE 0x4000
/*
* FLASH on the Local Bus
*/
#define CFG_SYS_FLASH_BASE 0x40000000 /* FLASH base address */
#define CFG_SYS_FLASH_SIZE 64 /* FLASH size is 64M */
/*
* NAND
*/
#define CFG_SYS_NAND_BASE 0xa0000000
/*
* For booting Linux, the board info and command line data
* have to be in the first 256 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
/* Initial Memory map for Linux */
#define CFG_SYS_BOOTMAPSZ SZ_256M
/* Board names */
#define CFG_BOARD_CMPCXXX "cmpcpro"
#define CFG_BOARD_MCR3000_2G "mcrpro"
#define CFG_BOARD_VGOIP "vgoippro"
#define CFG_BOARD_MIAE "miaepro"
#endif /* __CONFIG_H */