u-boot/include/configs/usb_a9263.h
Tom Rini eaf6ea6a1d Migrate CUSTOM_SYS_INIT_SP_ADDR to Kconfig using system-constants.h
- Make all users of CUSTOM_SYS_INIT_SP_ADDR reference SYS_INIT_SP_ADDR
- Introduce HAS_CUSTOM_SYS_INIT_SP_ADDR to allow for setting the stack
  pointer directly, otherwise we use the common calculation.
- On some platforms that were using the standard calculation but did not
  set CONFIG_SYS_INIT_RAM_SIZE / CONFIG_SYS_INIT_RAM_ADDR, set them.
- On a small number of platforms that were not subtracting
  GENERATED_GBL_DATA_SIZE do so now via the standard calculation.
- CONFIG_SYS_INIT_SP_OFFSET is now widely unused, so remove it from most
  board config header files.

Signed-off-by: Tom Rini <trini@konsulko.com>
2022-06-06 12:09:19 -04:00

60 lines
1.7 KiB
C

/* SPDX-License-Identifier: GPL-2.0+ */
/*
* (C) Copyright 2007-2013
* Stelian Pop <stelian.pop@leadtechdesign.com>
* Lead Tech Design <www.leadtechdesign.com>
* Thomas Petazzoni, Free Electrons, <thomas.petazzoni@free-electrons.com>
* Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
*
* Settings for Calao USB-A9263 board
*
* U-Boot image has to be less than 200704 bytes, otherwise at91bootstrap
* installed on board will not be able to load it properly.
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/hardware.h>
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* 12 MHz crystal */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
/*
* Hardware drivers
*/
/* SDRAM */
#define CONFIG_SYS_SDRAM_BASE ATMEL_BASE_CS1
#define CONFIG_SYS_SDRAM_SIZE 0x04000000
#define CONFIG_SYS_INIT_RAM_SIZE (16 * 1024)
#define CONFIG_SYS_INIT_RAM_ADDR ATMEL_BASE_SRAM1
/* NAND flash */
#ifdef CONFIG_CMD_NAND
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE ATMEL_BASE_CS3
/* our ALE is AD21 */
#define CONFIG_SYS_NAND_MASK_ALE (1 << 21)
/* our CLE is AD22 */
#define CONFIG_SYS_NAND_MASK_CLE (1 << 22)
#define CONFIG_SYS_NAND_ENABLE_PIN GPIO_PIN_PD(15)
#define CONFIG_SYS_NAND_READY_PIN GPIO_PIN_PA(22)
#endif
/* USB */
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_ATMEL
#define CONFIG_USB_OHCI_NEW
#define CONFIG_SYS_USB_OHCI_CPU_INIT
#define CONFIG_SYS_USB_OHCI_REGS_BASE 0x00a00000
#define CONFIG_SYS_USB_OHCI_SLOT_NAME "at91sam9263"
#define CONFIG_SYS_USB_OHCI_MAX_ROOT_PORTS 2
#endif
/* bootstrap + u-boot + env + linux in dataflash on CS0 */
#define CONFIG_EXTRA_ENV_SETTINGS \
"mtdparts=" CONFIG_MTDPARTS_DEFAULT "\0" \
#endif