u-boot/board/freescale/imx8qm_mek
Peng Fan 0d331c035a imx: support i.MX8QM MEK board
Add i.MX8QM MEK board support.
Included a basic dts, enabled SPL FIT

Boot log as below:
U-Boot SPL 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)
Normal Boot
Trying to boot from MMC2_2

U-Boot 2019.01-rc1-00029-gf002213219 (Dec 24 2018 - 10:28:30 +0800)

CPU:   NXP i.MX8QM RevB A53 at 142933 MHz

Model: Freescale i.MX8QM MEK
Board: iMX8QM MEK
Build: SCFW 9330215b
Boot:  SD1
DRAM:  6 GiB
MMC:   FSL_SDHC: 0, FSL_SDHC: 1
Loading Environment from MMC... *** Warning - bad CRC, using default environment

In:    serial@5a060000
Out:   serial@5a060000
Err:   serial@5a060000
Net:
Error: ethernet@5b040000 address not set.
eth-1: ethernet@5b040000
Hit any key to stop autoboot:  0

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2019-04-25 17:03:25 +02:00
..
imx8qm_mek.c imx: support i.MX8QM MEK board 2019-04-25 17:03:25 +02:00
imximage.cfg imx: support i.MX8QM MEK board 2019-04-25 17:03:25 +02:00
Kconfig imx: support i.MX8QM MEK board 2019-04-25 17:03:25 +02:00
MAINTAINERS imx: support i.MX8QM MEK board 2019-04-25 17:03:25 +02:00
Makefile imx: support i.MX8QM MEK board 2019-04-25 17:03:25 +02:00
README imx: support i.MX8QM MEK board 2019-04-25 17:03:25 +02:00
spl.c imx: support i.MX8QM MEK board 2019-04-25 17:03:25 +02:00

U-Boot for the NXP i.MX8QM EVK board

Quick Start
===========

- Build the ARM Trusted firmware binary
- Get scfw_tcm.bin and ahab-container.img
- Build U-Boot
- Flash the binary into the SD card
- Boot

Get and Build the ARM Trusted firmware
======================================

$ git clone https://source.codeaurora.org/external/imx/imx-atf
$ cd imx-atf/
$ git checkout origin/imx_4.14.78_1.0.0_ga -b imx_4.14.78_1.0.0_ga
$ make PLAT=imx8qm bl31

Get scfw_tcm.bin and ahab-container.img
==============================

$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/imx-sc-firmware-1.1.bin
$ chmod +x imx-sc-firmware-1.1.bin
$ ./imx-sc-firmware-1.1.bin
$ wget https://www.nxp.com/lgfiles/NMG/MAD/YOCTO/firmware-imx-8.0.bin
$ chmod +x firmware-imx-8.0.bin
$ ./firmware-imx-8.0.bin

Copy the following binaries to U-Boot folder:

$ cp imx-atf/build/imx8qm/release/bl31.bin .
$ cp u-boot/u-boot.bin .

Copy the following firmwares U-Boot folder :

$ cp firmware-imx-7.6/firmware/seco/ahab-container.img .
$ cp imx-sc-firmware-0.7/mx8qm-mek-scfw-tcm.bin	.

Build U-Boot
============
$ export ATF_LOAD_ADDR=0x80000000
$ export BL33_LOAD_ADDR=0x80020000
$ make imx8qm_mek_defconfig
$ make flash.bin
$ dd if=u-boot.itb of=flash.bin bs=512 seek=1984

Flash the binary into the SD card
=================================

Burn the flash.bin binary to SD card offset 32KB:

$ sudo dd if=flash.bin of=/dev/sd[x] bs=1024 seek=32

Boot
====
Set Boot switch SW2: 1100.