u-boot/board/freescale/t208xrdb/t208xrdb.c
Tom Rini e4c3ce7e28 CONFIG_SYS_CLK_FREQ: Consistently be static or get_board_sys_clk()
This CONFIG option is used in one of two ways.  The first way is that it
is defined to a static value, of an unsigned long size.  The second way
is that it is defined to something, typically a function, to determine
this value at run time.

However, in a few cases that function returns a static value.  Change
that to using the static value directly.

In the case of using something at run time, convert everything to using
a function of the same name and prototype.  This will allow for further
cleanups.

Finally, we have a few cases where the function is just not used, so
drop it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-12-27 16:20:18 -05:00

177 lines
3.6 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2009-2013 Freescale Semiconductor, Inc.
* Copyright 2021 NXP
*/
#include <common.h>
#include <command.h>
#include <env.h>
#include <fdt_support.h>
#include <i2c.h>
#include <image.h>
#include <init.h>
#include <netdev.h>
#include <asm/global_data.h>
#include <linux/compiler.h>
#include <asm/mmu.h>
#include <asm/processor.h>
#include <asm/immap_85xx.h>
#include <asm/fsl_law.h>
#include <asm/fsl_serdes.h>
#include <asm/fsl_liodn.h>
#include <fm_eth.h>
#include "t208xrdb.h"
#include "cpld.h"
#include "../common/vid.h"
DECLARE_GLOBAL_DATA_PTR;
u8 get_hw_revision(void)
{
u8 ver = CPLD_READ(hw_ver);
switch (ver) {
default:
case 0x1:
return 'C';
case 0x0:
return 'D';
case 0x2:
return 'E';
}
}
int checkboard(void)
{
struct cpu_type *cpu = gd->arch.cpu;
static const char *freq[3] = {"100.00MHZ", "125.00MHz", "156.25MHZ"};
printf("Board: %sRDB, ", cpu->name);
printf("Board rev: %c CPLD ver: 0x%02x, boot from ",
get_hw_revision(), CPLD_READ(sw_ver));
#ifdef CONFIG_SDCARD
puts("SD/MMC\n");
#elif CONFIG_SPIFLASH
puts("SPI\n");
#else
u8 reg;
reg = CPLD_READ(flash_csr);
if (reg & CPLD_BOOT_SEL) {
puts("NAND\n");
} else {
reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
printf("NOR vBank%d\n", reg);
}
#endif
puts("SERDES Reference Clocks:\n");
printf("SD1_CLK1=%s, SD1_CLK2=%s\n", freq[2], freq[0]);
printf("SD2_CLK1=%s, SD2_CLK2=%s\n", freq[0], freq[0]);
return 0;
}
int board_early_init_r(void)
{
const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
int flash_esel = find_tlb_idx((void *)flashbase, 1);
/*
* Remap Boot flash + PROMJET region to caching-inhibited
* so that flash can be erased properly.
*/
/* Flush d-cache and invalidate i-cache of any FLASH data */
flush_dcache();
invalidate_icache();
if (flash_esel == -1) {
/* very unlikely unless something is messed up */
puts("Error: Could not find TLB for FLASH BASE\n");
flash_esel = 2; /* give our best effort to continue */
} else {
/* invalidate existing TLB entry for flash + promjet */
disable_tlb(flash_esel);
}
set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
0, flash_esel, BOOKE_PAGESZ_256M, 1);
/*
* Adjust core voltage according to voltage ID
* This function changes I2C mux to channel 2.
*/
if (adjust_vdd(0))
printf("Warning: Adjusting core voltage failed.\n");
return 0;
}
int misc_init_r(void)
{
u8 reg;
/* Reset CS4315 PHY */
reg = CPLD_READ(reset_ctl);
reg |= CPLD_RSTCON_EDC_RST;
CPLD_WRITE(reset_ctl, reg);
/* Enable POR for boards revisions D and up */
if (get_hw_revision() >= 'D') {
reg = CPLD_READ(misc_csr);
reg |= CPLD_MISC_POR_EN;
CPLD_WRITE(misc_csr, reg);
}
return 0;
}
int ft_board_setup(void *blob, struct bd_info *bd)
{
phys_addr_t base;
phys_size_t size;
ft_cpu_setup(blob, bd);
base = env_get_bootm_low();
size = env_get_bootm_size();
fdt_fixup_memory(blob, (u64)base, (u64)size);
#ifdef CONFIG_PCI
pci_of_setup(blob, bd);
#endif
fdt_fixup_liodn(blob);
fsl_fdt_fixup_dr_usb(blob, bd);
#ifdef CONFIG_SYS_DPAA_FMAN
fdt_fixup_board_fman_ethernet(blob);
fdt_fixup_board_enet(blob);
fdt_fixup_board_phy(blob);
#endif
return 0;
}
ulong *cs4340_get_fw_addr(void)
{
ulong cortina_fw_addr = CONFIG_CORTINA_FW_ADDR;
#ifdef CONFIG_SYS_CORTINA_FW_IN_NOR
u8 reg;
reg = CPLD_READ(flash_csr);
if (!(reg & CPLD_BOOT_SEL)) {
reg = ((reg & CPLD_LBMAP_MASK) >> CPLD_LBMAP_SHIFT);
if (reg == 0)
cortina_fw_addr = CORTINA_FW_ADDR_IFCNOR;
else if (reg == 4)
cortina_fw_addr = CORTINA_FW_ADDR_IFCNOR_ALTBANK;
}
#endif
return (ulong *)cortina_fw_addr;
}