u-boot/board/samsung/arndale/arndale.c
Inderpal Singh 7da7651251 usb: exynos5: arndale: Add network support
Arndale board has AX88760, which is USB 2.0 Hub & USB 2.0 Ethernet Combo
controller, connected to HSIC Phy of USB host controller via USB3503 hub.

This patch uses board specific board_usb_init function to perform reset
sequence for USB3503 hub and enables the relevant config options for
network to work.

Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Signed-off-by: Chander Kashyap <chander.kashyap@linaro.org>
2014-01-13 12:23:28 +01:00

122 lines
2.2 KiB
C

/*
* Copyright (C) 2013 Samsung Electronics
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <usb.h>
#include <asm/arch/pinmux.h>
#include <asm/arch/dwmmc.h>
#include <asm/arch/gpio.h>
#include <asm/arch/power.h>
DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_USB_EHCI_EXYNOS
int board_usb_init(int index, enum usb_init_type init)
{
struct exynos5_gpio_part1 *gpio = (struct exynos5_gpio_part1 *)
samsung_get_base_gpio_part1();
/* Configure gpios for usb 3503 hub:
* disconnect, toggle reset and connect
*/
s5p_gpio_direction_output(&gpio->d1, 7, 0);
s5p_gpio_direction_output(&gpio->x3, 5, 0);
s5p_gpio_direction_output(&gpio->x3, 5, 1);
s5p_gpio_direction_output(&gpio->d1, 7, 1);
return 0;
}
#endif
int board_init(void)
{
gd->bd->bi_boot_params = (PHYS_SDRAM_1 + 0x100UL);
return 0;
}
int dram_init(void)
{
int i;
u32 addr;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
gd->ram_size += get_ram_size((long *)addr, SDRAM_BANK_SIZE);
}
return 0;
}
int power_init_board(void)
{
set_ps_hold_ctrl();
return 0;
}
void dram_init_banksize(void)
{
int i;
u32 addr, size;
for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
addr = CONFIG_SYS_SDRAM_BASE + (i * SDRAM_BANK_SIZE);
size = get_ram_size((long *)addr, SDRAM_BANK_SIZE);
gd->bd->bi_dram[i].start = addr;
gd->bd->bi_dram[i].size = size;
}
}
#ifdef CONFIG_GENERIC_MMC
int board_mmc_init(bd_t *bis)
{
int ret;
/* dwmmc initializattion for available channels */
ret = exynos_dwmmc_init(gd->fdt_blob);
if (ret)
debug("dwmmc init failed\n");
return ret;
}
#endif
static int board_uart_init(void)
{
int err = 0, uart_id;
for (uart_id = PERIPH_ID_UART0; uart_id <= PERIPH_ID_UART3; uart_id++) {
err = exynos_pinmux_config(uart_id, PINMUX_FLAG_NONE);
if (err) {
debug("UART%d not configured\n",
(uart_id - PERIPH_ID_UART0));
return err;
}
}
return err;
}
#ifdef CONFIG_BOARD_EARLY_INIT_F
int board_early_init_f(void)
{
int err;
err = board_uart_init();
if (err) {
debug("UART init failed\n");
return err;
}
return err;
}
#endif
#ifdef CONFIG_DISPLAY_BOARDINFO
int checkboard(void)
{
printf("\nBoard: Arndale\n");
return 0;
}
#endif