mirror of
https://github.com/AsahiLinux/u-boot
synced 2024-11-12 16:07:30 +00:00
59f6eb477e
The SPI NOR is a bit further away from the SoC on DHCOR than on DHCOM, which causes additional signal delay. At 108 MHz, this delay triggers a sporadic issue where the first bit of RX data is not received by the QSPI controller. There are two options of addressing this problem, either by using the DLYB block to compensate the extra delay, or by reducing the QSPI bus clock frequency. The former requires calibration and that is overly complex for SPL, so opt for the second option. This incurs 20ms delay during boot, when SPL loads U-Boot to DRAM. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Patrice Chotard <patrice.chotard@foss.st.com> Cc: Patrick Delaunay <patrick.delaunay@foss.st.com> Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
213 lines
4.7 KiB
Text
213 lines
4.7 KiB
Text
// SPDX-License-Identifier: (GPL-2.0 OR BSD-3-Clause)
|
|
/*
|
|
* Copyright (C) Linaro Ltd 2019 - All Rights Reserved
|
|
* Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
|
|
* Copyright (C) 2020 Marek Vasut <marex@denx.de>
|
|
*/
|
|
/dts-v1/;
|
|
|
|
#include "stm32mp157.dtsi"
|
|
#include "stm32mp15-pinctrl.dtsi"
|
|
#include "stm32mp15xxac-pinctrl.dtsi"
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/mfd/st,stpmic1.h>
|
|
|
|
/ {
|
|
aliases {
|
|
spi0 = &qspi;
|
|
};
|
|
|
|
memory@c0000000 {
|
|
device_type = "memory";
|
|
reg = <0xc0000000 0x40000000>;
|
|
};
|
|
};
|
|
|
|
&i2c4 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&i2c4_pins_a>;
|
|
i2c-scl-rising-time-ns = <185>;
|
|
i2c-scl-falling-time-ns = <20>;
|
|
status = "okay";
|
|
/delete-property/dmas;
|
|
/delete-property/dma-names;
|
|
|
|
pmic: stpmic@33 {
|
|
compatible = "st,stpmic1";
|
|
reg = <0x33>;
|
|
interrupts-extended = <&exti 55 IRQ_TYPE_EDGE_FALLING>;
|
|
interrupt-controller;
|
|
#interrupt-cells = <2>;
|
|
status = "okay";
|
|
|
|
regulators {
|
|
compatible = "st,stpmic1-regulators";
|
|
|
|
ldo1-supply = <&v3v3>;
|
|
ldo2-supply = <&v3v3>;
|
|
ldo3-supply = <&vdd_ddr>;
|
|
ldo5-supply = <&v3v3>;
|
|
ldo6-supply = <&v3v3>;
|
|
pwr_sw1-supply = <&bst_out>;
|
|
pwr_sw2-supply = <&bst_out>;
|
|
|
|
vddcore: buck1 {
|
|
regulator-name = "vddcore";
|
|
regulator-min-microvolt = <800000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-always-on;
|
|
regulator-initial-mode = <0>;
|
|
regulator-over-current-protection;
|
|
};
|
|
|
|
vdd_ddr: buck2 {
|
|
regulator-name = "vdd_ddr";
|
|
regulator-min-microvolt = <1350000>;
|
|
regulator-max-microvolt = <1350000>;
|
|
regulator-always-on;
|
|
regulator-initial-mode = <0>;
|
|
regulator-over-current-protection;
|
|
};
|
|
|
|
vdd: buck3 {
|
|
regulator-name = "vdd";
|
|
regulator-min-microvolt = <2900000>;
|
|
regulator-max-microvolt = <2900000>;
|
|
regulator-always-on;
|
|
regulator-initial-mode = <0>;
|
|
regulator-over-current-protection;
|
|
};
|
|
|
|
v3v3: buck4 {
|
|
regulator-name = "v3v3";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
regulator-over-current-protection;
|
|
regulator-initial-mode = <0>;
|
|
};
|
|
|
|
vdda: ldo1 {
|
|
regulator-name = "vdda";
|
|
regulator-min-microvolt = <2900000>;
|
|
regulator-max-microvolt = <2900000>;
|
|
interrupts = <IT_CURLIM_LDO1 0>;
|
|
interrupt-parent = <&pmic>;
|
|
};
|
|
|
|
v2v8: ldo2 {
|
|
regulator-name = "v2v8";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
interrupts = <IT_CURLIM_LDO2 0>;
|
|
interrupt-parent = <&pmic>;
|
|
};
|
|
|
|
vtt_ddr: ldo3 {
|
|
regulator-name = "vtt_ddr";
|
|
regulator-min-microvolt = <500000>;
|
|
regulator-max-microvolt = <750000>;
|
|
regulator-always-on;
|
|
regulator-over-current-protection;
|
|
};
|
|
|
|
vdd_usb: ldo4 {
|
|
regulator-name = "vdd_usb";
|
|
interrupts = <IT_CURLIM_LDO4 0>;
|
|
interrupt-parent = <&pmic>;
|
|
};
|
|
|
|
vdd_sd: ldo5 {
|
|
regulator-name = "vdd_sd";
|
|
regulator-min-microvolt = <2900000>;
|
|
regulator-max-microvolt = <2900000>;
|
|
interrupts = <IT_CURLIM_LDO5 0>;
|
|
interrupt-parent = <&pmic>;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
v1v8: ldo6 {
|
|
regulator-name = "v1v8";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
interrupts = <IT_CURLIM_LDO6 0>;
|
|
interrupt-parent = <&pmic>;
|
|
regulator-enable-ramp-delay = <300000>;
|
|
};
|
|
|
|
vref_ddr: vref_ddr {
|
|
regulator-name = "vref_ddr";
|
|
regulator-always-on;
|
|
};
|
|
|
|
bst_out: boost {
|
|
regulator-name = "bst_out";
|
|
interrupts = <IT_OCP_BOOST 0>;
|
|
interrupt-parent = <&pmic>;
|
|
};
|
|
|
|
vbus_otg: pwr_sw1 {
|
|
regulator-name = "vbus_otg";
|
|
interrupts = <IT_OCP_OTG 0>;
|
|
interrupt-parent = <&pmic>;
|
|
regulator-active-discharge = <1>;
|
|
};
|
|
|
|
vbus_sw: pwr_sw2 {
|
|
regulator-name = "vbus_sw";
|
|
interrupts = <IT_OCP_SWOUT 0>;
|
|
interrupt-parent = <&pmic>;
|
|
regulator-active-discharge = <1>;
|
|
};
|
|
};
|
|
|
|
onkey {
|
|
compatible = "st,stpmic1-onkey";
|
|
interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
|
|
interrupt-names = "onkey-falling", "onkey-rising";
|
|
status = "okay";
|
|
};
|
|
|
|
watchdog {
|
|
compatible = "st,stpmic1-wdt";
|
|
status = "disabled";
|
|
};
|
|
};
|
|
};
|
|
|
|
&iwdg2 {
|
|
timeout-sec = <32>;
|
|
status = "okay";
|
|
};
|
|
|
|
&pwr_regulators {
|
|
vdd-supply = <&vdd>;
|
|
vdd_3v3_usbfs-supply = <&vdd_usb>;
|
|
};
|
|
|
|
&qspi {
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&qspi_clk_pins_a &qspi_bk1_pins_a>;
|
|
pinctrl-1 = <&qspi_clk_sleep_pins_a &qspi_bk1_sleep_pins_a>;
|
|
reg = <0x58003000 0x1000>, <0x70000000 0x200000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
|
|
flash0: spi-flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-rx-bus-width = <4>;
|
|
spi-max-frequency = <50000000>;
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
};
|
|
};
|
|
|
|
&rng1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&rtc {
|
|
status = "okay";
|
|
};
|